The driver exits port setup after failing the lpfc_sli4_get_parameters
command (messages 0356, 2541, & 1412).

The older CNA adapters do not support the MBX command. In the past
the code was allowed to fail and continue on with initialization.
However a nvme change moved a closing bracket and now makes all
failures terminal.

Revise the logic so that terminal failure only occurs if the command
failed on the newer adapters. Additionally, if parameters are set
that require information from the command and the command failed,
the parameters are erroneous and port set up should fail even on
the older adapters.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The lancer G5 chip family fails the CQ create with 16k page size.  The
hardware incorrectly reports it supports large page sizes when it is
actually limited to 4k pages.

A prior patch resolved this for the A0 chip revision only.  This patch
excludes all revisions of the G5 asic from using large page sizes. As
knowing the actual chip revision is unnecessary, the now unused definitions
are removed
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Trivial fix to spelling mistakes in lpfc_printf_log log message

"mabilbox" -> "mailbox"
"maibox" -> "mailbox"
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fix small formatting and wording nits in Broadcom copyright header
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If the cpu count is larger than the number of WQ resources available,
adapter attachment eventually failes due to a WQ_CREATE failure.

Calculate the number of WQs desired (which initializes to cpu count)
after accounting for the number of queues the adapter supports and the
number allocated to SCSI and the control/ELS path, and scale down if
necessary.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The driver encounters a link event ACQE with a fault code it doesn't
recognize, it logs an "Invalid" fault type and futher treats the unknown
value as a mailbox command failure.  First off, there is no "invalid"
value, only values that are unknown. Secondly, the fault code doesn't
indicate status - the rest of the ACQE contains that status so there is
no reason to "fail the commands".

Change the "Invalid" to "Unknown". There is no "invalid" code value.

Separate fault code parsing and message genaration from any mbx handling
status.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In situations when the firmware image in inappropriate for the chip
type, initial validation checks were light, allowing the checks to pass,
thus allowing the firmware to be downloaded.  Eventually, after the
download, the chip rejects the firmware but it is logged as a generic
firmware download error.

Revise the initial checks to validate the image vs asic type so that the
correct message is displayed and the download process is avoided.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The patch to enlarge WQ/CQ creation keys off of an adapter response that
indicates support for the larger values. Older adapters return an
incorrect response and are limited in size.  Thus the adapters fail the
WQ creation steps.

Augment the WQ sizing checks with a check on the older adapter types and
limit them to the restricted sizes.

Fixes: c176ffa0 ("scsi: lpfc: Increase CQ and WQ sizes for SCSI")
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

After driver unloads, lpfc_wq remains active. The destroy_workqueue
calls were not being made in driver unload.  Additionally, SLI3 is
allocating lpfc_wq resources, but never uses it.

Make the destroy_workqueue calls on driver unload.  Modify the SLI3 code
path no longer allocate lpfc_wq resources.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When debugging various issues, per IO channel IO statistics were useful
to understand what was happening. However, many of the stats were on a
port basis rather than an io channel basis.

Move statistics to an io channel basis.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The driver fails to allocate command buffers in the routine
lpfc_new_scsi_buf_s4

There is an inconsistency between lpfc_mem_alloc(), where the
phba->lpfc_sg_dma_buf_pool is created, and lpfc_new_scsi_buf_s4(),
when we allocate a buffer from the pool and check the alignment.  The
alignment should be on a page boundary, based on LPFC_SLI3_BG_ENABLED in
sli3_options, for both cases.

Fix by explicitly tracking sli4 vs sli3 and BG options.  The result is that
phba->cfg_sg_dma_buf_size is now set correctly for SLI-4.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

To reduce latency when initializing WQE content, created templates for the
most common wqes. This reduces the number of operations taken to set the
content. It's not a lot of speed up, but every bit helps.

This patch updates the NVME target path.

[mkp: fixed typo]
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

To reduce latency when initializing WQE content, create templates for the
most common wqes. This reduces the number of operations taken to set the
content. It's not a lot of speed up, but every bit helps.

This patch updates the NVME initiator path.

[mkp: fixed typo]
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The hardware offload for NVME commands was created when the
FC-NVME standard was setting SGL Descriptor Type to SGL Data
Block Descriptor (0h) and SGL Descriptor Sub Type to Address (0h).

A late change in NVMe-over-Fabrics obsoleted these values, creating
a transport SGL descriptor type with new values to go into these
fields.

For initial hardware support, in order to be compliant to the spec,
use host-supplied cmd IU buffers instead of the adapter generated
values. Later hardware will correct this.

Add a module parameter to override this offload disablement if looking
for lowest latency. This is reasonable as nothing in FC-NVME uses
the SQE SGL values.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The current driver isn't taking advantage of a performance hint whereby
the initial data buffer descriptor can be placed in the WQE as well as
the SGL.

Add the logic to detect support for the feature and to use it when
supported.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Current code is very explicit in what it allows to be downloaded.
The driver checking prevented G7 firmware download. The driver
checking is unnecessary as the device will validate what it receives.

Revise the firmware download interface checking.
Added a little debug support in case there is still a failure.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Traditional SLI4 required the driver to clear Valid bits on
EQEs and CQEs after consuming them.

The new if_type=6 hardware will cycle the value for what is
valid on each queue itteration. The driver no longer has to
touch the valid bits. This also means all the cpu cache
dirtying and perhaps flush/refill's done by the hardware
in accessing the EQ/CQ elements is eliminated.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The G7 adapter supports 64G link speeds. Add support to the driver.

In addition, a small cleanup to replace the odd bitmap logic with
a switch case.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add PCI ids for the new G7 adapter
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

New if_type=6 adapters support an additional BAR that provides
apertures to allow direct WQE to adapter push support - termed
Direct Packet Push (DPP). WQ creation differs slightly to ask for
a WQ to be DPP-ized. When submitting a WQE to a DPP WQ, it is
submitted to the host memory for the WQ normally, but is also
written by the host cpu directly to a BAR aperture.  Write buffer
coalescing in hardware is (hopefully) turned on, enabling single
pci write operation support. The doorbell is thing rung to indicate
the WQE is available and was pushed to the aperture.

This patch:
- Updates the WQ Create commands for the DPP options
- Adds the bar mapping for if_type=6 DPP bar
- Adds the WQE pushing to the DDP aperture received from WQ create
- Adds a new module parameter to disable DPP operation if desired.
  Default is enabled.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

New hardware supports a SLI-4 interface, but with a new if_type
variant of 6.

If_type=6 has a different PCI BAR map, separate EQ/CQ doorbells,
and some changes in doorbell formats.

Add the changes for the if_type into headers, adapter initialization
and control flows. Add new eq and cq handlers.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Up until now, all SLI-4 devices had the same doorbells at the same
bar locations. With newer hardware, there are now independent EQ and
CQ doorbells and the bar locations differ.

Prepare the code for new hardware by separating the eq/cq doorbell into
separate components. The components can be set based on if_type.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Up until now, an SLI-4 device had no variance in the way it handled
its EQs and CQs. With newer hardware, there are now differences in
doorbells and some differences in how entries are valid.

Prepare the code for new hardware by creating a sli4-based callout
table that can be set based on if_type.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Updated Copyright in files updated 11.4.0.7
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When using the special option to suppress the response iu, ensure the
adapter fully supports the feature by checking feature flags from the
adapter and validating the support when formatting the WQE.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

During SCSI error handling escalation to host reset, the SCSI io
routines were moved off the txcmplq, but the individual io's ON_CMPLQ
flag wasn't cleared.  Thus, a background thread saw the io and attempted
to access it as if on the txcmplq.

Clear the flag upon removal.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Ensure nvme localports/targetports are torn down before dismantling the
adapter sli interface on driver detachment.  This aids leaving
interfaces live while nvme may be making callbacks to abort it.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Increased CQ and WQ sizes for SCSI FCP, matching those used for NVMe
development.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Increased the sizes of the SCSI WQ's and CQ's so that SCSI operation is
similar to that used by NVME. However, size increase restricted only to
those newer adapters that can support the larger WQE size, thus bigger
queue sizes.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

NVME targets appear to randomly disconnect from the initiator when
running heavy IO.

The error is due to the host aggregate (across all controllers) io load
was beyond the maximum exchange count for nvme on the adapter. The
driver was properly returning a resource busy status, but the io load
was so great heartbeat commands would be bounced and not have a
successful retry within the fuzz amount for the nvme heartbeat (yes, a
very high io load!). Thus the target was terminating the controller due
to a keep alive failure.

Resolve by reserving a few exchanges (by counters) which can be used
when the adapter is out of normal exchanges and the command is a NVME
heartbeat command. As counters are used, while the reserved command is
outstanding, as soon as any other exchange completes, the counters are
adjusted and the reserved count is replenished. The heartbeat completes
execution in a normal fashion.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The logic for sg_seg_cnt is a bit convoluted. This patch tries to clean
up a couple of areas, especially around the +2 and +1 logic.

This patch:

- Cleans up the lpfc_sg_seg_cnt attribute to specify a real minimum
  rather than making the minimum be whatever the default is.

- Removes the hardcoding of +2 (for the number of elements we use in a
  sgl for cmd iu and rsp iu) and +1 (an additional entry to compensate
  for nvme's reduction of io size based on a possible partial page)
  logic in sg list initialization. In the case where the +1 logic is
  referenced in host and target io checks, use the values set in the
  transport template as that value was properly set.

There can certainly be more done in this area and it will be addressed
in combined host/target driver effort.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

During driver unload, the driver may crash due to NULL pointers.  The
NULL pointers were due to the driver not protecting itself sufficiently
during some of the teardown paths.  Additionally, the driver was not
waiting for and cleanup up nvme io resources. As such, the driver wasn't
making the callbacks to the transport, stalling the transports
association teardown.

This patch waits for io clean up before tearding down and adds checks
for possible NULL pointers.

Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The current default for async hw receive queues is 1, which presents
issues under heavy load as number of queues influence the available
async receive buffer limits.

Raise the default to the either the current hw limit (16) or the number
of hw qs configured (io channel value).

Revise the attribute definition for mrq to better reflect what we do for
hw queues. E.g. 0 means default to optimal (# of cpus), non-zero
specifies a specific limit. Before this change, mrq=0 meant target mode
was disabled. As 0 now has a different meaning, rework the if tests to
use the better nvmet_support check.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In test cases where an instance of the driver is detached and
reattached, the driver will crash on reattachment. There is a compound
if statement that will skip over the bar setup if the pci_resource_start
call is not successful. The driver erroneously returns success to its
bar setup in this scenario even though the bars aren't properly
configured.

Rework the offending code segment for proper initialization steps.  If
the pci_resource_start call fails, -ENOMEM is now returned.

Sample stack:

rport-5:0-10: blocked FC remote port time out: removing rport
BUG: unable to handle kernel NULL pointer dereference at           (null)
... lpfc_sli4_wait_bmbx_ready+0x32/0x70 [lpfc]
...
...  RIP: 0010:...  ... lpfc_sli4_wait_bmbx_ready+0x32/0x70 [lpfc]
 Call Trace:
  ... lpfc_sli4_post_sync_mbox+0x106/0x4d0 [lpfc]
  ... ? __alloc_pages_nodemask+0x176/0x420
  ... ? __kmalloc+0x2e/0x230
  ... lpfc_sli_issue_mbox_s4+0x533/0x720 [lpfc]
  ... ? mempool_alloc+0x69/0x170
  ... ? dma_generic_alloc_coherent+0x8f/0x140
  ... lpfc_sli_issue_mbox+0xf/0x20 [lpfc]
  ... lpfc_sli4_driver_resource_setup+0xa6f/0x1130 [lpfc]
  ... ? lpfc_pci_probe_one+0x23e/0x16f0 [lpfc]
  ... lpfc_pci_probe_one+0x445/0x16f0 [lpfc]
  ... local_pci_probe+0x45/0xa0
  ... work_for_cpu_fn+0x14/0x20
  ... process_one_work+0x17a/0x440

Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

XRI_ABORTED_CQE completions were not being handled in the fast path.
They were being queued and deferred to the lpfc worker thread for
processing. This is an artifact of the driver design prior to moving
queue processing out of the isr and into a workq element. Now that queue
processing is already in a deferred context, remove this artifact and
process them directly.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Hardware queues are a fast staging area to push commands into the
adapter.  The adapter should drain them extremely quickly. However,
under heavy io load, the host cpu is pushing commands faster than the
drain rate of the adapter causing the driver to resource busy commands.

Enlarge the hardware queue (wq & cq) to support a larger number of queue
entries (4x the prior size) before backpressure. Enlarging the queue
requires larger contiguous buffers (16k) per logical page for the
hardware. This changed calling sequences that were expecting 4K page
sizes that now must pass a parameter with the page sizes. It also
required use of a new version of an adapter command that can vary the
page size values.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: NKees Cook <keescook@chromium.org>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>

Under heavy target nvme load duration, the lpfc irq handler is
encountering cpu lockup warnings.

Convert the driver to a shortened ISR handler which identifies the
interrupting condition then schedules a workq thread to process the
completion queue the interrupt was for. This moves all the real work
into the workq element.

As nvmet_fc upcalls are no longer in ISR context, don't set the feature
flags
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The driver crashes when attempting to use a freed ndpl pointer.

The pci_remove_one handler runs on a separate kernel thread. The order
of the removal is starting by freeing all of the ndlps and then
disabling interrupts. In between these two events the driver can still
receive an ELS and process it. When it tries to use the ndlp pointer
will be NULL

Change the order of the pci_remove_one vs disable interrupts so that
interrupts are disabled before the ndlp's are freed.

Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

During pci hot plug, the kernel crashes in timer management code.

The sli4 remove_one handler is not stoping the timers as it starts to
remove the port so that it can be swapped.

Fix: Stop the timers early in the handler routine.

Note: Fix in SLI-4 only. SLI-3 already stopped the timers properly.

Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>