Next hardware will direct packets to core based on the TCP/UDP
streams.
This logic can create holes in reorder buffer since packets that
belong to other stream were directed to a different core.
However, those are valid holes and the packets can be indicated
in L3 order.

The hardware will utilize a mechanism of informing the driver of
the normalized ssn and the driver shall release all packets that
SN is lower than the nssn.
This enables managing the reorder across the queues without sharing
any data between them.

The reorder buffer is allocated and released directly in the RX path
in order to avoid various races between control path and rx path.
The code utilizes the internal messaging to notify rx queues of when
to delete the reorder buffer.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

According to the spec when a BA session is started there
is a timeout set for the session in the ADDBA request.
If there is not activity on the TA/TID then the session
expires and a DELBA is sent.
In order to check for the timeout, data must be shared
among the rx queues.
Add a timer that runs as long as BA session is active
for the station and stops aggregation session if needed.
This patch also lays the infrastructure for the reordering
buffer which will be enabled in the next patches.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently the sync notification is a type of notification. However, it
is better fitted as an attribute of a notification, since there might
be another message in the payload (delba for instance) that should be
sent while control path is waiting for all queues to process.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

mac80211 will call the driver whenever there is a race between
RSS queues and control path that requires a processing of all
pending frames in RSS queues.
Implement that by utilizing the internal notification mechanism:
queue a message to all queues. When the message is received on
a queue it decrements the atomic counter. This guarantees that
all pending frames in the RX queue were processed since the message
is in order inside the queue.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If something goes wrong with the firmware and we never get a scan
complete notification, we stay stuck forever.  In order to avoid this
situation, add a timeout and trigger an NMI if it expires before
receiving the notification., so we can clean things up.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Set the correct sta_id in the SCD_QUEUE_CONFIG command sent
to the FW when enabling/disabling queues. This is needed in
DQA-mode to allow the FW to associate between queue and STA.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Improve current RSS configuration:
 * Use netdev_rss_key instead of keeping a local copy.
 * Configure also UDP hashing to have UDP traffic spread across queues.
 * Do not direct RSS traffic to our fallback queue.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

API version lower than 16 is not supported anymore - don't
load older ucode.
Remove code handling older versions.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

"DQA" is shorthand for "dynamic queue allocation". This
enables on-demand allocation of queues per RA/TID rather than
statically allocating per vif, thus allowing a potential
benefit of various factors.

Please refer to the DOC section this patch adds to sta.h to
see a more in-depth explanation of this feature.

There are many things to take into consideration when working
in DQA mode, and this patch is only one in a series. Note that
default operation mode is non-DQA mode, unless the FW
indicates that it supports DQA mode.

This patch enables support of DQA for a station connected to
an AP, and works in a non-aggregated mode.

When a frame for an unused RA/TID arrives at the driver, it
isn't TXed immediately, but deferred first until a suitable
queue is first allocated for it, and then TXed by a worker
that both allocates the queues and TXes deferred traffic.

When a STA is removed, its queues goes back into the queue
pools for reuse as needed.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to disable uapsd for BSS only, or P2P client
separately. Remove the now unneeded
IWL_MVM_P2P_UAPSD_STANDALONE constant.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This makes u-APSD work with more peers.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

LQM stands for Link Quality Measurement. The firmware
will collect a defined set of statitics (see the
notification for details) that allow to know how busy
the medium is. The driver issues a request to the firmware
that includes the duration of the measurement (the firmware
needs to be on channel for that amount of time) and the
timeout (in case the firmware has a lot of offchannel
activities). If the timeout elapses, the firmware will
send partial results which are still valuable.
In case of disassociation / channel switch and alike, the
driver is in charge of stopping the measurements and the
firmware will reply with partial results.

The user space API for now is debugfs only and will be
implmemented in an upcoming patch.
Signed-off-by: NAviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In case of FW error, support dumping the UMAC internal txfifos.
To do so, support version 2 of shared memory cfg command, which
contains the sizes of the internal txfifos, and move the command
to the system group.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwl_mvm_tcool_get_cur_state is the function that returns the
cooling state index to the sysfs handler. This function returns
mvm->cooling_dev.cur_state but that variable was set to the
budget and not the cooling state index. Fix that.
Add a missing blank line while at it.
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Thermal zone device registration can fail, and in this case
we don't want to remove WiFi functionality. This is why the
thermal zone registration function is void, and the flows
continue even if the thermal zone device registration failed.
Same applies for the cooling device.

This means that we at least need to remember that the thermal
zone device didn't register properly and take the minimal
precautions to avoid panic'ing when we access it.

This was missing.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a wrapper function to allow stopping SW queues from MVM
as well.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Do not allow entrance into DQA flows until feature is
completely ready and merged.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Leaving ucode_loaded to true after stop_device() has been called
is a recipe for problems. Flows that are not sync'ed with the
driver life cycle (like debugfs hooks and thermal hooks) must
check that the firmware is loaded before they interact with it.
Therefore we need to keep this variable updated with the real
status of the firmware.
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwl_mvm_enable_agg_txq has only one user. Kill it and
adapt the call site.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the device is in d0i3/d3 we will not receive the VHT
MU-MIMO group id management frame. Instead, firmware will
notify us upon exit on the current status and we can in turn
update mac80211. Support this notification.
While at it, also check as a precaution that the vif is indeed
the VHT MU-MIMO owner before updating the firmware.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In multi rx queue HW, without execessive locking, there is no sync
between the ctrl path (default queue) and the rest of the rx queues.
This might cause issues on certain situations. For example, in case
a delBA was processed on a default queue but out of order packets
still wait for processing on the other queue.

The solution is to introduce internal messaging between the CTRL path
and the other rx queues.
The driver will send a message to the firmware, which will echo it to
all the requested queues. The message will be in order inside the queue.
This way we can avoid CTRL path and RSS queues races.

Add support for this messaging mechanism. As the firmware is agnostic to
the data sent, add internal representation of the data as well.
Although currently only delBA flow will use it, the internal representation
will enable generic use of this infrastructure for future uses.
Next patch will utilize this messaging mechanism for the reorder buffer
delBA flow.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

During d0i3 frames might be filtered by the FW and this may
cause reordering buffer a delay - as the frames will not be
received and reorder will time out.

Introduce an API function to receive notification of filtered
frames and pass the information to the mac80211.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

in order to be able to tune the size of the desired A-MSDU
based on link condition, add a knob to modify the length
of the A-MSDU.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware doesn't send match found notifications when no matchsets
are passed.  This makes sense because if there are no matchsets,
nothing can be matched.  But the nl80211 API should report when there
are results available, even if no matchsets were passed.

To handle this, we can use the firmware's ITERATION_COMPLETE
reporting, which will send us notifications every time it completed a
scheduled scan iteration.  Then we can set a flag when we received
beacons and use that to report that results are available.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Register cooling device in order to have the Thermal
Manager handle the device's power budget according to the sent
notifications.
The interface adds a new thermal cooling device to
/sys/class/thermal/ folder.
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Register to thermal_zone interface and implement the
thermal ops.
The thermal handles the device throttling, and sets the
the temperature thresholds the Thermal Manager would be
notified of crossing.
The thermal interface adds a new thermal zone device sensor
under /sys/class/thermal/ folder.
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Up to today the driver was notified of the temperature from the FW
and decided whether to enter CT-kill or not.
From now on, the FW will decide when to enter CT-kill and will notify
the driver.
Add support for this notification.
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the opmode is stopped and started again we did not free
the paging buffers. Fix that.
In addition when freeing the firmware's paging download
buffer, set the pointer to NULL.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When in AP mode we need to filter in beacons from other APs to update HT
operation mode. As a power optimization the beacons are filtered out when
there are no associated stations. As a result, when there are no
associated stations, we will not update the HT operation mode until a
station connects.
Add a debugfs parameter that allows to disable this optimization.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

9000 series supports multi-queue rx. The hardware needs
to be configured with the hash functions to perform and
indirection table that maps hash results to the relevant
CPUs\queues.
Support this configuration.
Add debugfs hook to configure the indirection table in
order to enable performance analysis. The configuration
is stateless, receives a partial or full pattern and sends
the command to the firmware.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Previous patches enabled the multi-queue rx path based on
iwl_mvm_has_new_rx_api() which returned false by default.
Change it to return the actual value based on the firmware
TLV which is now defined.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For debug purposes, allow setting minimum quota (for a single
virtual interface) from debugfs. This is an absolute minimum,
so it can only be set up to 95%.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

To be able to test low-latency behaviour properly, split the
different low-latency sources so that setting any one of them,
for example from debugfs, is sufficient; this avoids getting
the debug setting overwritten by other sources.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently firmware is configured to filter out beacons. In case
a beacon was changed - it is waking the host.
However, some vendors change their IEs frequently without any
significant change, and redundant wakeups are triggered as a
result.
As a solution disable beacon filtering when entering d0i3.
Instead, firmware will store the latest beacon and upon exiting
d0i3 it will send it up to the host, so the host can act upon
changes (if there were any).
This beacon will arrive as a dedicated notification - support it
as well.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver should support also negative temperatures.
So there is a need to separate between the return value and
temperature in order to be able to distinguish between
a negative temperature and error value.
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enable snoozing and U-APSD on P2P client. The firwmare will
support this only if the BSS vif is not associated.
Make this configurable by a constant variable and disable
it by default.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The debug functions of fw-dbg.c don't really need to modify
the trigger and the description they receive as a parameter.
Constify the pointers.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow the user to configure a non-trigger session - a window
between triggers in which the driver won't collect fw debug data.
This can be useful when the frequent collection of fw data
has an impact on the performance, such as debugging
tx flows.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to let the fw do offloading properly, we need
to provide various key data (e.g. PN).

Configure the params on d0i3 entrance, and update them
back on d0i3 exit.

Since d3 code is now called in d0i3 which requires runtime
pm only, make d3.0 depend on CONFIG_PM (rather than
CONFIG_PM_SLEEP), and add required #ifdefs and wrappers
where needed, so both CONFIG_PM=n and CONFIG_PM_RUNTIME=n
configurations will build correctly.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>