The original wm_adsp2_early_event took an additional frequency
argument for clocking control so could not be used directly as a
DAPM callback. But this setup could equally be done by the codec
driver function wrapping wm_adsp2_early event. In preparation
for adding support for new core types wm_adsp2_set_dspclk has
been exported, and the freq argument removed so that it can
be used directly as a DAPM callback.
Signed-off-by: NRichard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This function is not presently called from outside the adsp code and nor
should it be, as such stop exporting it.
Signed-off-by: NCharles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

If a watchdog timeout is received from the DSP it is safe to assume the
DSP is not functioning anymore and as such any active compressed streams
should be put into an error state.
Signed-off-by: NCharles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Best to lock across handling the bus error to ensure the DSP doesn't
change power state as we are reading the status registers.
Signed-off-by: NCharles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

During recent logging improvements it seems two error messages lost
their updates during patch application/rebasing. Add these back in.

Fixes: 0d3fba3e ("ASoC: wm_adsp: Improve logging messages")
Signed-off-by: NCharles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Previously support was added to allow streams to be stopped and
started again without the DSP being power cycled and this was done
by clearing the buffer state in trigger start. Another supported
use-case is using the DSP for a trigger event then opening the
compressed stream later to receive the audio, unfortunately clearing
the buffer state in trigger start destroys the data received
from such a trigger. Correct this issue by moving the call to
wm_adsp_buffer_clear to be in trigger stop instead.

Fixes: 61fc060c ("ASoC: wm_adsp: Support streams which can start/stop with DSP active")
Signed-off-by: NCharles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Some strings are allocated by kstrdup, but not freed when error
happened.
Signed-off-by: NBard liao <yung-chuan.liao@linux.intel.com>
Acked-by: NPierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The stream_name is allocated by kstrdup. We have to free it when the
dai is removed or return from error.
Signed-off-by: NBard liao <yung-chuan.liao@linux.intel.com>
Acked-by: NPierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Merge branch 'for-5.1' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-5.2

It is parsing mclk_fs at many places, but it should be
same operation. This patch adds graph_parse_mclk_fs()
and parse it.

This patch also renames similar function graph_get_conversion()
to graph_parse_convert().
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

use same naming rule, and this patch add missing of_node_put() on it
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

It is parsing mclk_fs at many places, but it should be
same operation. This patch adds simple_parse_mclk_fs()
and parse it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

use same naming rule
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

If ASRC turns on, HW will use clk_dac as the reference clock
whether recording or playback.
Both of clk_dac and clk_adc should set proper clock while using ASRC.
Signed-off-by: NShuming Fan <shumingf@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The jack type detection needs the main bias power of analog.
The modification makes sure the main bias power on/off while jack plug/unplug.
Signed-off-by: NShuming Fan <shumingf@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The IRQ function may not work when system suspend.
We remove snd_soc_dapm_force_enable_pin function call to
make sure the bias off when idle and run into suspend/resume function.
Signed-off-by: NShuming Fan <shumingf@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Skip for i2s5 in mck_disable which is also bypassed in mck_enable.
Signed-off-by: NTzung-Bi Shih <tzungbi@google.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add BYT_RT5651_JD_NOT_INV quirk for devices with an inverted
(active-high instead of the normal active-low) jack-detect switch.

And add a quirk for the Complet Electro Serv MY8307 tablet which has
an inverted jack-detect switch (and a mono-speaker).
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Some boards use a jack-receptacle with a switch which reports the
jack-inserted status as active-high, rather then the standard active-low
reporting most jacks use.

This commit adds support for it. This is activated by a boolean
"realtek,jack-detect-not-inverted" device-property. The not-inverted
in the device-property name, rather then active-high, was chosen to keep
the device-property naming consistent with the rt5640 codec driver.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add suspend and resume sleep callbacks to STM32 SPDIFRX driver,
to support system low power modes.
Signed-off-by: NOlivier Moysan <olivier.moysan@st.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The dpcm get from fe_clients/be_clients
may be free before use

Add a spin lock at snd_soc_card level,
to protect the dpcm instance.
The lock may be used in atomic context, so use spin lock.

possible race condition between
void dpcm_be_disconnect(
	...
	list_del(&dpcm->list_be);
	list_del(&dpcm->list_fe);
	kfree(dpcm);
	...

and
	for_each_dpcm_fe()
	for_each_dpcm_be*()

race condition example
Thread 1:
    snd_soc_dapm_mixer_update_power()
        -> soc_dpcm_runtime_update()
            -> dpcm_be_disconnect()
                -> kfree(dpcm);
Thread 2:
    dpcm_fe_dai_trigger()
        -> dpcm_be_dai_trigger()
            -> snd_soc_dpcm_can_be_free_stop()
                -> if (dpcm->fe == fe)

Excpetion Scenario:
	two FE link to same BE
	FE1 -> BE
	FE2 ->

	Thread 1: switch of mixer between FE2 -> BE
	Thread 2: pcm_stop FE1

Exception:

Unable to handle kernel paging request at virtual address dead0000000000e0

pc=<> [<ffffff8960e2cd10>] dpcm_be_dai_trigger+0x29c/0x47c
	sound/soc/soc-pcm.c:3226
		if (dpcm->fe == fe)
lr=<> [<ffffff8960e2f694>] dpcm_fe_dai_do_trigger+0x94/0x26c

Backtrace:
[<ffffff89602dba80>] notify_die+0x68/0xb8
[<ffffff896028c7dc>] die+0x118/0x2a8
[<ffffff89602a2f84>] __do_kernel_fault+0x13c/0x14c
[<ffffff89602a27f4>] do_translation_fault+0x64/0xa0
[<ffffff8960280cf8>] do_mem_abort+0x4c/0xd0
[<ffffff8960282ad0>] el1_da+0x24/0x40
[<ffffff8960e2cd10>] dpcm_be_dai_trigger+0x29c/0x47c
[<ffffff8960e2f694>] dpcm_fe_dai_do_trigger+0x94/0x26c
[<ffffff8960e2edec>] dpcm_fe_dai_trigger+0x3c/0x44
[<ffffff8960de5588>] snd_pcm_do_stop+0x50/0x5c
[<ffffff8960dded24>] snd_pcm_action+0xb4/0x13c
[<ffffff8960ddfdb4>] snd_pcm_drop+0xa0/0x128
[<ffffff8960de69bc>] snd_pcm_common_ioctl+0x9d8/0x30f0
[<ffffff8960de1cac>] snd_pcm_ioctl_compat+0x29c/0x2f14
[<ffffff89604c9d60>] compat_SyS_ioctl+0x128/0x244
[<ffffff8960283740>] el0_svc_naked+0x34/0x38
[<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: NKaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Some amplifier may not have a GPIO to control the power, but instead simply
rely on the regulator to power up and down the amplifier.

In order to support those setups, let's make the GPIO optional.
Signed-off-by: NMylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

If SoC has extended Audio DMAC peri peri address,
DT needs to select it.
Otherwise, it can select normal Audio DMAC peri peri address.
Extended Audio DMAC peri peri address can use BUSIF4-7,
normal address can't.
Reported-by: NJiada Wang <jiada_wang@mentor.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NMark Brown <broonie@kernel.org>

reg is missing "Audio DMAC peri peri" part,
and reg-name itself is missing at Document.
This patch add these.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NMark Brown <broonie@kernel.org>

Linux 5.1-rc1

Linux 5.1-rc1

Pull more Kbuild updates from Masahiro Yamada:

 - add more Build-Depends to Debian source package

 - prefix header search paths with $(srctree)/

 - make modpost show verbose section mismatch warnings

 - avoid hard-coded CROSS_COMPILE for h8300

 - fix regression for Debian make-kpkg command

 - add semantic patch to detect missing put_device()

 - fix some warnings of 'make deb-pkg'

 - optimize NOSTDINC_FLAGS evaluation

 - add warnings about redundant generic-y

 - clean up Makefiles and scripts

* tag 'kbuild-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: remove stale lxdialog/.gitignore
  kbuild: force all architectures except um to include mandatory-y
  kbuild: warn redundant generic-y
  Revert "modsign: Abort modules_install when signing fails"
  kbuild: Make NOSTDINC_FLAGS a simply expanded variable
  kbuild: deb-pkg: avoid implicit effects
  coccinelle: semantic code search for missing put_device()
  kbuild: pkg: grep include/config/auto.conf instead of $KCONFIG_CONFIG
  kbuild: deb-pkg: introduce is_enabled and if_enabled_echo to builddeb
  kbuild: deb-pkg: add CONFIG_ prefix to kernel config options
  kbuild: add workaround for Debian make-kpkg
  kbuild: source include/config/auto.conf instead of ${KCONFIG_CONFIG}
  unicore32: simplify linker script generation for decompressor
  h8300: use cc-cross-prefix instead of hardcoding h8300-unknown-linux-
  kbuild: move archive command to scripts/Makefile.lib
  modpost: always show verbose warning for section mismatch
  ia64: prefix header search path with $(srctree)/
  libfdt: prefix header search paths with $(srctree)/
  deb-pkg: generate correct build dependencies

Pull x86 asm updates from Thomas Gleixner:
 "Two cleanup patches removing dead conditionals and unused code"

* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm: Remove unused __constant_c_x_memset() macro and inlines
  x86/asm: Remove dead __GNUC__ conditionals

Pull perf fixes from Thomas Gleixner:
 "Three fixes for the fallout from the TSX errata workaround:

   - Prevent memory corruption caused by a unchecked out of bound array
     index.

   - Two trivial fixes to address compiler warnings"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Make dev_attr_allow_tsx_force_abort static
  perf/x86: Fixup typo in stub functions
  perf/x86/intel: Fix memory corruption

Pull xen fix from Juergen Gross:
 "A fix for a Xen bug introduced by David's series for excluding
  ballooned pages in vmcores"

* tag 'for-linus-5.1b-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: Fix mapping PG_offline pages to user space

Pull 9p updates from Dominique Martinet:
 "Here is a 9p update for 5.1; there honestly hasn't been much.

  Two fixes (leak on invalid mount argument and possible deadlock on
  i_size update on 32bit smp) and a fall-through warning cleanup"

* tag '9p-for-5.1' of git://github.com/martinetd/linux:
  9p/net: fix memory leak in p9_client_create
  9p: use inode->i_lock to protect i_size_write() under 32-bit
  9p: mark expected switch fall-through

Fixes: 400816f6 ("perf/x86/intel: Implement support for TSX Force Abort")
Signed-off-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: kbuild-all@01.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190313184243.GA10820@lkp-sb-ep06

When this .gitignore was added, lxdialog was an independent hostprogs-y.

Now that all objects in lxdialog/ are directly linked to mconf, the
lxdialog is no longer generated.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Currently, every arch/*/include/uapi/asm/Kbuild explicitly includes
the common Kbuild.asm file. Factor out the duplicated include directives
to scripts/Makefile.asm-generic so that no architecture would opt out
of the mandatory-y mechanism.

um is not forced to include mandatory-y since it is a very exceptional
case which does not support UAPI.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

The generic-y is redundant under the following condition:

 - arch has its own implementation

 - the same header is added to generated-y

 - the same header is added to mandatory-y

If a redundant generic-y is found, the warning like follows is displayed:

  scripts/Makefile.asm-generic:20: redundant generic-y found in arch/arm/include/asm/Kbuild: timex.h

I fixed up arch Kbuild files found by this.
Suggested-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

This reverts commit caf6fe91.

The commit was fine but is no longer needed as of commit 3a2429e1
("kbuild: change if_changed_rule for multi-line recipe").  Let's go
back to using ";" to be consistent.

For some discussion, see:

https://lkml.kernel.org/r/CAK7LNASde0Q9S5GKeQiWhArfER4S4wL1=R_FW8q0++_X3T5=hQ@mail.gmail.comSigned-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

During a simple no-op (nothing changed) build I saw 39 invocations of
the C compiler with the argument "-print-file-name=include".  We don't
need to call the C compiler 39 times for this--one time will suffice.

Let's change NOSTDINC_FLAGS to a simply expanded variable to avoid
this since there doesn't appear to be any reason it should be
recursively expanded.

On my build this shaved ~400 ms off my "no-op" build.

Note that the recursive expansion seems to date back to the (really
old) commit e8f5bdb0 ("[PATCH] Makefile include path ordering").
It's a little unclear to me if the point of that patch was to switch
the variable to be recursively expanded (which it did) or to avoid
directly assigning to NOSTDINC_FLAGS (AKA to switch to +=) because
someone else (out of tree?) was setting it.  I presume later since if
the only goal was to switch to recursive expansion the patch would
have just removed the ":".
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

* The man page for dpkg-source(1) notes:

>      -b, --build directory [format-specific-parameters]
>             Build  a  source  package  (--build since dpkg 1.17.14).
>             <...>
>
>             dpkg-source will build the source package with the first
>             format found in this ordered list: the format  indicated
>             with  the  --format  command  line  option,  the  format
>             indicated in debian/source/format, “1.0”.  The  fallback
>             to “1.0” is deprecated and will be removed at some point
>             in the future, you should always  document  the  desired
>             source   format  in  debian/source/format.  See  section
>             SOURCE PACKAGE FORMATS for an extensive  description  of
>             the various source package formats.

  Thus it would be more foolproof to explicitly use 1.0 (as we always
  did) than to rely on dpkg-source's defaults.

* In a similar vein, debian/rules is not made executable by mkdebian,
  and dpkg-source warns about that but still silently fixes the file.
  Let's be explicit once again.
Signed-off-by: NArseny Maslennikov <ar@cs.msu.ru>
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>