Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 01 10月, 2011 3 次提交
    • A
      ARM: OMAP: musb: Remove a redundant omap4430_phy_init call in usb_musb_init · b8e111a7
      由 Axel Lin 提交于 
      Current code calls omap4430_phy_init() twice in usb_musb_init().
Calling omap4430_phy_init() once is enough.
This patch removes the first omap4430_phy_init() call, which using an
uninitialized pointer as parameter.

This patch elimates below build warning:
arch/arm/mach-omap2/usb-musb.c: In function 'usb_musb_init':
arch/arm/mach-omap2/usb-musb.c:141: warning: 'dev' may be used uninitialized in this function
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Bjarne Steinsbo <bsteinsbo@gmail.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      b8e111a7
    • T
      ARM: OMAP: Fix i2c init for twl4030 · bfd46a54
      由 Tony Lindgren 提交于 
      Looks like 2600 kHz rate does not work reliably on 2430,
so just use the 100 kHz rate.

Otherwise the system often fails to boot properly with:

omap_i2c omap_i2c.2: timeout waiting for bus ready
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
twl: clock init err [-110]
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
TWL4030 Unable to unlock IDCODE registers --110
Signed-off-by: NTony Lindgren <tony@atomide.com>
      bfd46a54
    • B
      ARM: OMAP4: MMC: fix power and audio issue, decouple USBC1 from MMC1 · 3696d303
      由 Bryan Buckley 提交于 
      Remove OMAP4_USBC1_ICUSB_PWRDNZ_MASK during enable/disable PWRDNZ mode for
MMC1_PBIAS and associated extended-drain MMC1 I/O cell. This is in accordance
with the control module programming guide. This fixes a bug where if trying to
use gpio_98 or gpio_99 and MMC1 at the same time the GPIO signal will be
affected by a changing SDMMC1_VDDS.

Software must keep MMC1_PBIAS cell and MMC1_IO cell PWRDNZ signals low whenever
SDMMC1_VDDS ramps up/down or changes for cell protection purposes.

MMC1 is based on SDMMC1_VDDS whereas USBC1 is based on SIM_VDDS therefore
they can operate independently.
Signed-off-by: NBryan Buckley <bryan.buckley@ti.com>
Acked-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      3696d303
  3. 27 9月, 2011 2 次提交
  5. 26 9月, 2011 6 次提交
  7. 21 9月, 2011 3 次提交
    • R
      ARM: fix vmlinux.lds.S discarding sections · 6760b109
      由 Russell King 提交于 
      We are seeing linker errors caused by sections being discarded, despite
the linker script trying to keep them.  The result is (eg):

`.exit.text' referenced in section `.alt.smp.init' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
`.exit.text' referenced in section `.alt.smp.init' of net/built-in.o: defined in discarded section `.exit.text' of net/built-in.o

This is the relevent part of the linker script (reformatted to make it
clearer):
| SECTIONS
| {
| /*
| * unwind exit sections must be discarded before the rest of the
| * unwind sections get included.
| */
| /DISCARD/ : {
| *(.ARM.exidx.exit.text)
| *(.ARM.extab.exit.text)
| }
| ...
| .exit.text : {
| *(.exit.text)
| *(.memexit.text)
| }
| ...
| /DISCARD/ : {
| *(.exit.text)
| *(.memexit.text)
| *(.exit.data)
| *(.memexit.data)
| *(.memexit.rodata)
| *(.exitcall.exit)
| *(.discard)
| *(.discard.*)
| }
| }

Now, this is what the linker manual says about discarded output sections:

|    The special output section name `/DISCARD/' may be used to discard
| input sections.  Any input sections which are assigned to an output
| section named `/DISCARD/' are not included in the output file.

No questions, no exceptions. It doesn't say "unless they are listed
before the /DISCARD/ section." Now, this is what asn-generic/vmlinux.lds.S
says:
| /*
|  * Default discarded sections.
|  *
|  * Some archs want to discard exit text/data at runtime rather than
|  * link time due to cross-section references such as alt instructions,
|  * bug table, eh_frame, etc. DISCARDS must be the last of output
|  * section definitions so that such archs put those in earlier section
|  * definitions.
|  */

And guess what - the list _always_ includes .exit.text etc.

Now, what's actually happening is that the linker is reading the script,
and it finds the first /DISCARD/ output section at the beginning of the
script. It continues reading the script, and finds the 'DISCARD' macro
at the end, which having been postprocessed results in another
/DISCARD/ output section. As the linker already contains the earlier
/DISCARD/ output section, it adds it to that existing section, so it
effectively is placed at the start. This can be seen by using the -M
option to ld:

| Linker script and memory map
|
|                 0xc037c080                jiffies = jiffies_64
|
| /DISCARD/
|  *(.ARM.exidx.exit.text)
|  *(.ARM.extab.exit.text)
|  *(.exit.text)
|  *(.memexit.text)
|  *(.exit.data)
|  *(.memexit.data)
|  *(.memexit.rodata)
|  *(.exitcall.exit)
|  *(.discard)
|  *(.discard.*)
|
|                 0xc0008000                . = 0xc0008000
|
| .head.text      0xc0008000      0x1d0
|                 0xc0008000                _text = .
|  *(.head.text)
|  .head.text     0xc0008000      0x1d0 arch/arm/kernel/head.o
|                 0xc0008000                stext
|
| .text           0xc0008200   0x2d78d0
|                 0xc0008200                _stext = .
|                 0xc0008200                __exception_text_start = .
|  *(.exception.text)
|  .exception.text
| ...

As you can see, all the discarded sections are grouped together - and
as a result of it being the first output section, they all appear before
any other section.

The result is that not only is the unwind information discarded (as
intended), but also the .exit.text, despite us wanting to have the
.exit.text preserved.

We can't move the unwind information elsewhere, because it'll then be
included even when we do actually discard the .exit.text (and similar)
sections.

So, work around this by avoiding the generic DISCARDS macro, and instead
conditionalize the sections to be discarded ourselves.  This avoids the
ambiguity in how the linker assigns input sections to output sections,
making our script less dependent on undocumented linker behaviour.
Reported-by: NRob Herring <robherring2@gmail.com>
Tested-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      6760b109
    • L
      mach-integrator: fix VGA base regression · b71d8429
      由 Linus Walleij 提交于 
      The changes introduced in commit
cc22b4c1
"ARM: set vga memory base at run-time"

Makes the Integrator/AP freeze completely. I appears that
this is due to the VGA base address being assigned at PCI
init time, while this base is needed earlier than that.
Moving the initialization of the base address to the
.map_io function solves this problem.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
      b71d8429
    • S
      arm/dt: Tegra: Update SDHCI nodes to match bindings · a0638eb6
      由 Stephen Warren 提交于 
      The bindings were recently updated to have separate properties for each
type of GPIO. Update the Device Tree source to match that.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
      a0638eb6
  9. 20 9月, 2011 2 次提交
  11. 17 9月, 2011 2 次提交
  13. 16 9月, 2011 1 次提交
    • L
      asm alternatives: remove incorrect alignment notes · a7f934d4
      由 Linus Torvalds 提交于 
      On x86-64, they were just wasteful: with the explicitly added (now
unnecessary) padding, the size of the alternatives structure was 16
bytes, and an alignment of 8 bytes didn't hurt much.

However, it was still silly, since the natural size and alignment for
the structure is actually just 12 bytes, 4-byte aligned since commit
59e97e4d ("x86: Make alternative instruction pointers relative").
So removing the padding, and removing the extra alignment is just a good
idea.

On x86-32, the alignment of 4 bytes was correct, but was incorrectly
hardcoded as 8 bytes in <asm/alternative-asm.h>.  That header file had
used to be an x86-64 only header file, but various unification efforts
have made it be used for x86-32 too (ie the unification of rwlock and
rwsem).

That in turn caused x86-32 boot failures, because the extra alignment
would result in random zero-filled words in the altinstructions section,
causing oopses early at boot when doing alternative instruction
replacement.

So just remove all the alignment noise entirely.  It's wrong, and it's
unnecessary.  The section itself is already properly aligned by the
linker scripts, and all additions to the section had better be of the
proper 12-byte format, keeping it aligned.  So if the align directive
were to ever make a difference, that would be an indication of a serious
bug to begin with.
Reported-by: NWerner Landgraf <w.landgraf@ru.r>
Acked-by: NAndrew Lutomirski <luto@mit.edu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      a7f934d4
  15. 15 9月, 2011 19 次提交
  17. 14 9月, 2011 1 次提交
  19. 13 9月, 2011 1 次提交
    • D
      xen/e820: if there is no dom0_mem=, don't tweak extra_pages. · e3b73c4a
      由 David Vrabel 提交于 
      The patch "xen: use maximum reservation to limit amount of usable RAM"
(d312ae87) breaks machines that
do not use 'dom0_mem=' argument with:

reserve RAM buffer: 000000133f2e2000 - 000000133fffffff
(XEN) mm.c:4976:d0 Global bit is set to kernel page fffff8117e
(XEN) domain_crash_sync called from entry.S
(XEN) Domain 0 (vcpu#0) crashed on cpu#0:
...

The reason being that the last E820 entry is created using the
'extra_pages' (which is based on how many pages have been freed).
The mentioned git commit sets the initial value of 'extra_pages'
using a hypercall which returns the number of pages (if dom0_mem
has been used) or -1 otherwise. If the later we return with
MAX_DOMAIN_PAGES as basis for calculation:

    return min(max_pages, MAX_DOMAIN_PAGES);

and use it:

     extra_limit = xen_get_max_pages();
     if (extra_limit >= max_pfn)
             extra_pages = extra_limit - max_pfn;
     else
             extra_pages = 0;

which means we end up with extra_pages = 128GB in PFNs (33554432)
- 8GB in PFNs (2097152, on this specific box, can be larger or smaller),
and then we add that value to the E820 making it:

  Xen: 00000000ff000000 - 0000000100000000 (reserved)
  Xen: 0000000100000000 - 000000133f2e2000 (usable)

which is clearly wrong. It should look as so:

  Xen: 00000000ff000000 - 0000000100000000 (reserved)
  Xen: 0000000100000000 - 000000027fbda000 (usable)

Naturally this problem does not present itself if dom0_mem=max:X
is used.

CC: stable@kernel.org
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
      e3b73c4a