The pfvf exchange need be in exclusive mode. And add pfvf exchange in gpu
reset.
Signed-off-by: NEmily Deng <Emily.Deng@amd.com>
Reviewed-By: NXiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

For virtual display feature, no need to pin cursor bo.
Signed-off-by: NEmily Deng <Emily.Deng@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

XGMI hive put kfd_pre_reset into amdgpu_device_lock_adev,
but outside req_full_gpu of sriov.
It would make sriov hang during reset.
Signed-off-by: NWentao Lou <Wentao.Lou@amd.com>
Reviewed-by: NShaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

I retested Bonaire (gfx7 dGPU) and it works fine.
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

SI does not use doorbells, move asic doorbell init later
asic check.

Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=108920Reviewed-by: NOak Zeng <Oak.Zeng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use per hive wq to concurrently send reset commands to all nodes
in the hive.

v2:
Switch to system_highpri_wq after dropping dedicated queue.
Fix non XGMI code path KASAN error.
Stop  the hive reset for each node loop if there
is a reset failure on any of the nodes.
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

XGMI hive has some resources allocted on device init which
needs to be deallocated when the device is unregistered.

v2: Remove creation of dedicated wq for XGMI hive reset.
v3: Use the gmc.xgmi.supported flag
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When paging queue is enabled, it use the second page of doorbell.
The AMDGPU_DOORBELL64_MAX_ASSIGNMENT definition assumes all the
kernel doorbells are in the first page. So with paging queue enabled,
the total kernel doorbell range should be original num_doorbell plus
one page (0x400 in dword), not *2.
Signed-off-by: NOak Zeng <ozeng@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

For XGMI hive case do reset in steps where each step iterates over
all devs in hive. This especially important for asic reset
since all PSP FW in hive must come up within a limited time
(around 1 sec) to properply negotiate the link.
Do this by  refactoring  amdgpu_device_gpu_recover and amdgpu_device_reset
into pre_asic_reset, asic_reset and post_asic_reset functions where is part
is exectued for all the GPUs in the hive before going to the next step.

v2: Update names for amdgpu_device_lock/unlock functions.

v3: Introduce per hive locking to avoid multiple resets for GPUs
    in same hive.
v4:
Remove delayed_workqueue()/ttm_bo_unlock_delayed_workqueue() - they
are copy & pasted over from radeon and on amdgpu there isn't
any reason for that any more.
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This is prep work for updating each PSP FW in hive after
GPU reset.
Split into build topology SW state and update each PSP FW in the hive.
Save topology and count of XGMI devices for reuse.

v2: Create seperate header for XGMI.
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

ASIC specific doorbell layout is used instead of enum definition
Signed-off-by: NOak Zeng <ozeng@amd.com>
Suggested-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Suggested-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Also call functioin amdgpu_device_doorbell_init after
amdgpu_device_ip_early_init because the former depends
on the later to set up asic-specific init_doorbell_index
function
Signed-off-by: NOak Zeng <ozeng@amd.com>
Suggested-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Suggested-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Because increase SDMA_DOORBELL_RANGE to add new SDMA doorbell for paging queue will
break SRIOV, instead we can reserve and map two doorbell pages for amdgpu, paging
queues doorbell index use same index as SDMA gfx queues index but on second page.

For Vega20, after we change doorbell layout to increase SDMA doorbell for 8 SDMA RLC
queues later, we could use new doorbell index for paging queue.
Signed-off-by: NPhilip Yang <Philip.Yang@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Setup and tear down xgmi as part of psp.

v2:
- make psp_xgmi_terminate static
- squash in:
drm/amdgpu: only issue xgmi cmd when it is enabled
drm/amdgpu/psp: terminate xgmi ta in suspend and hw_fini phase
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

There is no functional changes,
Use function arguments for SRIOV special variables which
is hardcode in those functions.

so we can share those functions in baremetal.
Reviewed-by: NMonk Liu <Monk.Liu@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

After testing looks like these subset of ASICs has GPU reset
working for the most part. Enable reset due to job timeout.

v2: Switch from GFX version to ASIC type.
v3: Fix identation
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This is still completely breaking my Raven system.

This reverts commit cdf2f910fa969adca1b0e3ad2b487821233dc038.

Revert until we sort out the sbios and firmware combinations that work
correctly.

bug: https://bugs.freedesktop.org/show_bug.cgi?id=108606
Cc: stable@vger.kernel.org # v4.19
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Problem:
During GPU recover DAL would hang in
amdgpu_pm_compute_clocks->amdgpu_fence_wait_empty

Fix:
Turns out there was a typo introduced by
3320b8d2 drm/amdgpu: remove job->ring which caused skipping
amdgpu_fence_driver_force_completion and so the hangged job
was never force signaled and this would cause the hang later in DAL.
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Need to check adev->powerplay.pp_funcs.
Signed-off-by: NEmily Deng <Emily.Deng@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Extract the function of fw loading out of powerplay.
Do fw loading between hw_init/resuem_phase1 and phase2
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We need to do some IPs earlier to deal with ordering issues
similar to how resume is split into two phases.

Will do fw loading via smu/psp between the two phases.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

1. one is for create/free bo when init/fini
2. one is for fill the bo before fw loading

the ucode bo only need to be created when load driver
and free when driver unload.

when resume/reset, driver only need to re-fill the bo
if the bo is allocated in vram.

Suggested by Christian.

v2: Return error when bo create failed.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fix cg/pg unexpected set in hw init failed case.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

1. only call late_init when hw_init successful,
   so check status.hw instand of status.valid in late_init.
2. set status.late_initialized true if late_init was not implemented.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Move in_suspend flag to adev from gfx, so
can be used in other ip blocks, also keep
consistent with gpu_in_reset flag.
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

MGPU fan boost feature is enabled only when two or more dGPUs
in the system.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Don't grab the reservation lock any more and simplify the handling quite
a bit.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

It shouldn't add much overhead and we should make sure that critical
VRAM content is always restored.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NJunwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Treat them all as Raven rather than adding a new picasso
asic type.  This simplifies a lot of code and also handles the
case of rv2 chips with the 0x15d8 pci id.  It also fixes dmcu
fw handling for picasso.
Acked-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add gpu_info firmware for raven2.
Signed-off-by: NFeifei Xu <Feifei.Xu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

enable gfxoff in non-sriov and stutter mode by default
Signed-off-by: NKenneth Feng <kenneth.feng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add support for picasso to the display manager.
Signed-off-by: NLikun Gao <Likun.Gao@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add the IP blocks, clock and powergating flags, and common clockgating support.
Signed-off-by: NLikun Gao <Likun.Gao@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add picasso to amd_asic_type enum and amdgpu_asic_name[].
Signed-off-by: NLikun Gao <Likun.Gao@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

since we use PSP to program IH regs now
Signed-off-by: NMonk Liu <Monk.Liu@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NEmily Deng <Emily.Deng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Driver will save an array of XGMI hive info, each hive will have a list of devices
that have the same hive ID.
Signed-off-by: NShaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

since we use PSP to program IH regs now
Signed-off-by: NMonk Liu <Monk.Liu@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NEmily Deng <Emily.Deng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Move that into amdgpu_gmc.c since we are really deadling with GMC
address space here.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NJunwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

It will be more safe to make full-acess include both phase1 and phase2.
Then accessing special registeris wherever at phase1 or phase2 will not
block any shutdown and suspend process under virtualization.
Signed-off-by: NYintian Tao <yttao@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Check if we should call the function instead of providing the forced
flag.

v2: rebase on KFD changes (Alex)
Signed-off-by: NChristian König <christian.koenig@amd.com>
Acked-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>