The spec says it "may be problematic" if CPU x registers the VPA of
CPU y. Add a warning in case we ever do that.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

As a part of pseries_idle backend driver cleanup to make
the code common to both pseries and powernv platforms, it
is necessary to move the backend-driver code to drivers/cpuidle.

As a pre-requisite for that, it is essential to move plpar_wrapper.h
to include/asm.
Signed-off-by: NDeepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

As a part of pseries_idle cleanup to make the backend driver
code common to both pseries and powernv.
Remove non-essential smt_snooze_delay declaration in pseries.h
header file and pseries.h file inclusion in
pseries/processor_idle.c
Signed-off-by: NDeepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The lppaca, slb_shadow and dtl_entry hypervisor structures are
big endian, so we have to byte swap them in little endian builds.

LE KVM hosts will also need to be fixed but for now add an #error
to remind us.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We pass dma_window to of_parse_dma_window as a void * and then
run through hoops to cast it back to a u32 array. In the process
we lose endian annotation.

Simplify it by just passing a __be32 * down.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

T4, Cell, powernv, and pseries had the same implementation, so switch
them to use a generic version. A2 apparently had a version, but
removed it at some point, so we remove the declaration, too.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Although the shared_proc field in the lppaca works today, it is
not architected. A shared processor partition will always have a non
zero yield_count so use that instead. Create a wrapper so users
don't have to know about the details.

In order for older kernels to continue to work on KVM we need
to set the shared_proc bit. While here, remove the ugly bitfield.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Address some of the trivial sparse warnings in arch/powerpc.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

plpar_get_term_char is only used once and just adds a layer
of complexity to H_GET_TERM_CHAR. plpar_put_term_char isn't
used at all so we can remove it.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 801eb73f introduced
a bug while checking PTE flags. We have to drop the _PAGE_COHERENT flag
when __PAGE_NO_CACHE is set and the cache update policy is not write-through
(i.e. _PAGE_WRITETHRU is not set)
Signed-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
CC:  Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch introduces flag EEH_DEV_SYSFS to keep track that the sysfs
entries for the corresponding EEH device (then PCI device) has been
added or removed, in order to avoid race condition.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

While restoring BARs for one specific PCI device, the pci_dev
instance should have been released. So it's not reliable to use
the pci_dev instance on restoring BARs. However, we still need
some information (e.g. PCIe capability position, header type) from
the pci_dev instance. So we have to store those information to
EEH device in advance.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When EEH error happens to one specific PE, some devices with drivers
supporting EEH won't except hotplug on the device. However, there
might have other deivces without driver, or with driver without EEH
support. For the case, we need do partial hotplug in order to make
sure that the PE becomes absolutely quite during reset. Otherise,
the PE reset might fail and leads to failure of error recovery.

The current code doesn't handle that 'mixed' case properly, it either
uses the error callbacks to the drivers, or tries hotplug, but doesn't
handle a PE (EEH domain) composed of a combination of the two.

The patch intends to support so-called "partial" hotplug for EEH:
Before we do reset, we stop and remove those PCI devices without
EEH sensitive driver. The corresponding EEH devices are not detached
from its PE, but with special flag. After the reset is done, those
EEH devices with the special flag will be scanned one by one.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

During Machine Check interrupt on pseries platform, R3 generally points to
memory region inside RTAS (FWNMI) area. We see r3 corruption because when RTAS
delivers the machine check exception it passes the address inside FWNMI area
with the top most bit set. This patch fixes this issue by masking top two bit
in machine check exception handler.
Signed-off-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The Kconfig symbol HOTPLUG was removed with commit 40b31360 ("Finally
eradicate CONFIG_HOTPLUG"). But there's still one select statement for
that symbol. It seems that select statement was added after the patch to
remove CONFIG_HOTPLUG was submitted. Anyhow, it is useless and can be
dropped.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Reviewed-by: NSrivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch set supports compression of oops messages while writing to NVRAM,
this helps in capturing more of oops data to lnx,oops-log. The pstore file
for oops messages will be in decompressed format making it readable.

In case compression fails, the patch takes care of copying the header added
by pstore and last oops_data_sz bytes of big_oops_buf to NVRAM so that we
have recent oops messages in lnx,oops-log.

In case decompression fails, it will result in absence of oops file but still
have files (in /dev/pstore) for other partitions.
Signed-off-by: NAruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

nvram_compress() and zip_oops() is used by the nvram_pstore_write
API to compress oops messages hence re-organise the functions
accordingly to avoid forward declarations.
Signed-off-by: NAruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Header size is needed to distinguish between header and the dump data.
Incorporate the addition of new argument (hsize) in the pstore write
callback.
Signed-off-by: NAruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Acked-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

On LPAR systems we need to inform the hypervisor that we are using the
EBB registers. We do this by setting a bit in the Virtual Processor Area
(VPA) - formerly known as the lppaca.

For now we do this always, ie. we do not dynamically enable/disable.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NSebastien Bessiere <sebastien.bessiere@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

While running Linux as guest on top of phyp, we possiblly have
PE that includes single PCI device. However, we didn't return
its PCI bus correctly and it leads to failure on recovery from
EEH errors for single-dev-PE. The patch fixes the issue.

Cc: <stable@vger.kernel.org> # v3.7+
Cc: Steve Best <sbest@us.ibm.com>
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

commit f8f7d63f ("powerpc/eeh: Trace eeh
device from I/O cache") broke EEH on pseries for devices that were
present during boot and have not been hotplugged/DLPARed.

eeh_check_failure will get the eeh_dev from the cache, and will get
NULL. eeh_addr_cache_build adds the addresses to the cache, but eeh_dev
for the giving pci_device is not set yet. Just reordering the call to
eeh_addr_cache_insert_dev works fine. The ordering is similar to the one
in eeh_add_device_late.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Hugepage invalidate involves invalidating multiple hpte entries.
Optimize the operation using H_BULK_REMOVE on lpar platforms.
On native, reduce the number of tlb flush.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If a hash bucket gets full, we "evict" a more/less random entry from it.
When we do that we don't invalidate the TLB (hpte_remove) because we assume
the old translation is still technically "valid". This implies that when
we are invalidating or updating pte, even if HPTE entry is not valid
we should do a tlb invalidate. With hugepages, we need to pass the correct
actual page size value for tlb invalidation.

This change update the patch 0608d692
"powerpc/mm: Always invalidate tlb on hpte invalidate and update" to handle
transparent hugepages correctly.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch moves the common part of EEH core into arch/powerpc/kernel
directory so that we needn't PPC_PSERIES while compiling POWERNV
platform:

        * Move the EEH common part into arch/powerpc/kernel
        * Move the functions for PCI hotplug from pSeries platform to
          arch/powerpc/kernel/pci-hotplug.c
        * Move CONFIG_EEH from arch/powerpc/platforms/pseries/Kconfig to
          arch/powerpc/platforms/Kconfig
        * Adjust makefile accordingly
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Cleanup on EEH core to remove unnecessary whitespaces.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch exploits pstore subsystem to read details of common partition
in NVRAM to a separate file in /dev/pstore. For instance, common partition
details will be stored in a file named [common-nvram-6].
Signed-off-by: NAruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: NJim Keniston <jkenisto@us.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch set exploits the pstore subsystem to read details of
of-config partition in NVRAM to a separate file in /dev/pstore.
For instance, of-config partition details will be stored in a
file named [of-nvram-5].
Signed-off-by: NAruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: NJim Keniston <jkenisto@us.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Introduce os_partition member in nvram_os_partition structure to identify
if the partition is an os partition or not. This will be useful to handle
non-os partitions of-config and common.
Signed-off-by: NAruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: NJim Keniston <jkenisto@us.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch set exploits the pstore subsystem to read details of rtas partition
in NVRAM to a separate file in /dev/pstore. For instance, rtas details will be
stored in a file named [rtas-nvram-4].
Signed-off-by: NAruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: NJim Keniston <jkenisto@us.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

IBM's p series machines provide persistent storage for LPARs through NVRAM.
NVRAM's lnx,oops-log partition is used to log oops messages.
Currently the kernel provides the contents of p-series NVRAM only as a
simple stream of bytes via /dev/nvram, which must be interpreted in user
space by the nvram command in the powerpc-utils package.

This patch set exploits the pstore subsystem to expose oops partition in
NVRAM as a separate file in /dev/pstore. For instance, Oops messages will be
stored in a file named [dmesg-nvram-2]. In case pstore registration fails it
will fall back to kmsg_dump mechanism.

This patch will read/write the oops messages from/to this partition via pstore.
Signed-off-by: NJim Keniston <jkenisto@us.ibm.com>
Signed-off-by: NAruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Introduce generic read function to read nvram partitions other than rtas.
nvram_read_error_log will be retained which is used to read rtas partition
from rtasd. nvram_read_partition is the generic read function to read from
any nvram partition.
Signed-off-by: NAruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: NJim Keniston <jkenisto@us.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Introduce version and timestamp information in the oops header.
oops_log_info (oops header) holds version (to distinguish between old
and new format oops header), length of the oops text
(compressed or uncompressed) and timestamp.

The version field will sit in the same place as the length in old
headers. version is assigned 5000 (greater than oops partition size)
so that existing tools will refuse to dump new style partitions as
the length is too large. The updated tools will work with both
old and new format headers.
Signed-off-by: NAruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: NJim Keniston <jkenisto@us.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Removal of syslog prefix in the uncompressed oops text will
help in capturing more oops data.
Signed-off-by: NAruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: NJim Keniston <jkenisto@us.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

While running Linux as guest on top of phyp, we possiblly have
PE that includes single PCI device. However, we didn't return
its PCI bus correctly and it leads to failure on recovery from
EEH errors for single-dev-PE. The patch fixes the issue.

Cc: <stable@vger.kernel.org> # v3.7+
Cc: Steve Best <sbest@us.ibm.com>
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

orderly_poweroff is expecting a bool parameter, so
use 'true' instead '1'
Signed-off-by: Nliguang <lig.fnst@cn.fujitsu.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

'system_state < SYSTEM_RUNNING' will have same effect
with 'system_state == SYSTEM_BOOTING', but the later
one is more clearer.
Signed-off-by: Nliguang <lig.fnst@cn.fujitsu.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The enables VFIO on the pSeries platform, enabling user space
programs to access PCI devices directly.
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Acked-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

RTAS token "ibm,get-config-addr-info" or ibm,get-config-addr-info2"
are used to retrieve the PE address according to PCI address, which
made up of domain/bus/slot/function. If we don't have those 2 tokens,
the domain/bus/slot/function would be used as the address for EEH
RTAS operations. Some older f/w might not have those 2 tokens and
that blocks the EEH functionality to be initialized. It was introduced
by commit e2af155c ("powerpc/eeh: pseries platform EEH initialization").

The patch skips the check on those 2 tokens so we can bring up EEH
functionality successfully. And domain/bus/slot/function will be
used as address for EEH RTAS operations.

Cc: <stable@vger.kernel.org> # v3.4+
Reported-by: NRobert Knight <knight@princeton.edu>
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: NRobert Knight <knight@princeton.edu>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>