When a priority is marked as lossless using DCB PFC, or when pause frames
are enabled on a port, mlxsw adds to port buffers an extra space to cover
the traffic that will arrive between the time that a pause or PFC frame is
emitted, and the time traffic actually stops. This is called the delay. The
concept is the same in PFC and pause, however the way the extra buffer
space is calculated differs.

In this patch, unify this handling. Delay is to be measured in bytes of
extra space, and will not include MTU. PFC handler sets the delay directly
from the parameter it gets through the DCB interface.

To convert pause handler, move MLXSW_SP_PAUSE_DELAY to ethtool module,
convert to bytes, and reduce it by maximum MTU, and divide by two. Then it
has the same meaning as the delay_bytes set by the PFC handler.

Keep the delay_bytes value in struct mlxsw_sp_hdroom introduced in the
previous patch. Change PFC and pause handlers to store the new delay value
there and have __mlxsw_sp_port_headroom_set() take it from there.

Instead of mlxsw_sp_pfc_delay_get() and mlxsw_sp_pg_buf_delay_get(),
introduce mlxsw_sp_hdroom_buf_delay_get() to calculate the delay provision.
Drop the unnecessary MLXSW_SP_CELL_FACTOR, and instead add an explanatory
comment describing the formula used.
Signed-off-by: NPetr Machata <petrm@nvidia.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The port headroom handling is currently strewn across several modules and
tricky to follow: MTU, DCB PFC, DCB ETS and ethtool pause all influence the
settings, and then there is the completely separate initial configuraion in
spectrum_buffers. A following patch will implement the dcbnl_setbuffer
callback, which is going to further complicate the landscape.

In order to simplify work with port buffers, the following patches are
going to centralize all port-buffer handling in spectrum_buffers. As a
first step, introduce a (currently empty) struct mlxsw_sp_hdroom that will
keep the configuration parameters, and allocate and free it in appropriate
places.
Signed-off-by: NPetr Machata <petrm@nvidia.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As CHELSIO_INLINE_CRYPTO is bool, and CHELSIO_T4 is tristate, the
dependency of CHELSIO_INLINE_CRYPTO on CHELSIO_T4 is not sufficient to
protect CRYPTO_DEV_CHELSIO_TLS and CHELSIO_IPSEC_INLINE.  The latter two
are also tristate, hence if CHELSIO_T4=n, they cannot be builtin, as
that would lead to link failures like:

    drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_main.c:259: undefined reference to `cxgb4_port_viid'

and

    drivers/net/ethernet/chelsio/inline_crypto/ch_ipsec/chcr_ipsec.c:752: undefined reference to `cxgb4_reclaim_completed_tx'

Fix this by re-adding dependencies on CHELSIO_T4 to tristate symbols.
The dependency of CHELSIO_INLINE_CRYPTO on CHELSIO_T4 is kept to avoid
asking the user.

Fixes: 6bd860ac ("chelsio/chtls: CHELSIO_INLINE_CRYPTO should depend on CHELSIO_T4")
Reported-by: Nkernel test robot <lkp@intel.com>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce devlink health reporter to report FW fatal events. Implement
the event listener using MFDE trap and enable the events to be
propagated using MFGD register configuration.
Signed-off-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce MFGD register that is used to configure firmware debugging.
Signed-off-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce MFDE register that is passed through MFDE trap in case of
fatal FW event.
Signed-off-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the fw flashing code was moved to core.c, move the param which is
related to it there as well. Remove unnecessary parentheses on the way.
Signed-off-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract the code calling params register/unregister driver ops into
separate functions. Call publish/unpublish unconditionally.
Signed-off-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the firmware flashing is not specific to Spectrum, move the code to
core.c and avoid one op call and 2 exported symbols. Also, this allows
to do flash before call of driver->init function and possibly do other
core calls in between.

Do some small renaming here and there on the way to be consistent with
the rest of core.c code.
Signed-off-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Among other changes, this version supports FW monitoring.
Signed-off-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation of stmmac_stop_all_queues() and
stmmac_start_all_queues() will not work correctly when the value of
tx_queues_to_use is changed through ethtool -L DEVNAME rx N tx M command.

Also, netif_tx_start|stop_all_queues() are only needed in driver open()
and close() only.

Fixes: c22a3f48 net: stmmac: adding multiple napi mechanism
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NVoon Weifeng <weifeng.voon@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_set_real_num_tx_queues() & netif_set_real_num_rx_queues() should be
used to inform network stack about the real Tx & Rx queue (active) number
in both stmmac_open() and stmmac_resume(), therefore, we move the code
from stmmac_dvr_probe() to stmmac_hw_setup().

Fixes: c02b7a91 net: stmmac: use netif_set_real_num_{rx,tx}_queues
Signed-off-by: NAashish Verma <aashishx.verma@intel.com>
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restructure NAPI add and delete process so that we can call them
accordingly in open() and ethtool_set_channels() accordingly.

Introduced stmmac_reinit_queues() to handle the transition needed
for changing Rx & Tx channels accordingly.
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check if the pause stats are reported by HW by checking the bitmap.
Calculation is based on the order of strings in main_strings from
ethtool -S. Hopefully the semantics of these stats match the standard..
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Plumb through all the indirection and copy some code from
ethtool -S. The names of the group indicate that these are
the stats we are after (and Saeed confirms it).

v3:
 - fix build in mlx5_rep
v2:
 - drop the ethool helper and call stats directly
 - don't pass 0 as initialized to in buffer
 - use local buffer
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report standard pause frame stats. They are already aggregated
in struct ixgbe_hw_stats.

The combination of the registers is suggested as equivalent to
PAUSEMACCtrlFramesTransmitted / PAUSEMACCtrlFramesReceived
by the Intel 82576EB datasheet, I could not find any information
in the HW actually supported by ixgbe.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NAlexander Duyck <alexander.h.duyck@linux.intel.com>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These stats are already reported in ethtool -S.
Michael confirms they are equivalent to standard stats.

v2: - fix sparse warning about endian by using the macro
    - use u64 for pointer type
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Reviewed-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add minimal ethtool interface for testing ethtool pause stats.

v2: add missing static on nsim_ethtool_ops
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Documentation/networking/switchdev.txt and 'man bridge' indicate that the
learning_sync bridge attribute is used to control whether a given
device will sync MAC addresses learned on its device port to a master
bridge FDB, where they will show up as 'extern_learn offload'. So we map
qeth_l2_dev2br_an_set() to the learning_sync bridge link attribute.

Turning off learning_sync will flush all extern_learn entries from the
bridge fdb and all pending events from the card's work queue.

When the hardware interface goes offline with learning_sync on
(e.g. for HW recovery), all extern_learn entries will be flushed from the
bridge fdb and all pending events from the card's work queue. When the
interface goes online again, it will send new notifications for all then
valid MACs. learning_sync attribute can not be modified while interface is
offline. See
'commit e6e771b3 ("s390/qeth: detach netdevice while card is offline")'

An alternative implementation would be to always offload the 'learning'
attribute of a software bridge to the hardware interface attached to it
and thus implicitly enable fdb notification. This was not chosen for 2
reasons:
1) In our case the software bridge is NOT a representation of a hardware
switch. It is just connected to a smart NIC that is able to inform
about the addresses attached to it. It is not necessarily using source
MAC learning for this and other bridgeports can be attached to other
NICs with different properties.
2) We want a means to enable this notification explicitly. There may be
cases where a bridgeport is set to 'learning', but we do not want to
enable the notification.
Signed-off-by: NAlexandra Winter <wintera@linux.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Documentation/networking/switchdev.txt and 'man bridge' indicate that the
learning_sync bridge attribute is used to indicate whether a given
device will sync MAC addresses learned on its device port to a master
bridge FDB.

learning_sync attribute can not be read while interface is offline (down).
See
'commit e6e771b3 ("s390/qeth: detach netdevice while card is offline")'
We return EOPNOTSUPP and not EONODEV in this case, because EONOTSUPP is the
only rc that is tolerated by 'bridge -d link show'.
Signed-off-by: NAlexandra Winter <wintera@linux.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case hardware sends more device-to-bridge-address-change notfications
than the qeth-l2 driver can handle, the hardware will send an overflow
event and then stop sending any events. It expects software to flush its
FDB and start over again. Re-enabling address-change-notification will
report all current addresses.

In order to re-enable address-change-notification this patch defines
the functions qeth_l2_dev2br_an_set() and qeth_l2_dev2br_an_set_cb
to enable or disable dev-to-bridge-address-notification.

A following patch will use the learning_sync bridgeport flag to trigger
enabling or disabling of address-change-notification, so we define
priv->brport_features to store the current setting. BRIDGE_INFO and
ADDR_INFO functionality are mutually exclusive, whereas ADDR_INFO and
qeth_l2_vnicc* can be used together.

Alternative implementations to handle buffer overflow:
Just re-enabling notification and adding all newly reported addresses
would cover any lost 'add' events, but not the lost 'delete' events.
Then these invalid addresses would stay in the bridge FDB as long as the
device exists.
Setting the net device down and up, would be an alternative, but is a bit
drastic. If the net device has many secondary addresses this will create
many delete/add events at its peers which could de-stabilize the
network segment.
Signed-off-by: NAlexandra Winter <wintera@linux.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A qeth-l2 HiperSockets card can show switch-ish behaviour in the sense,
that it can report all MACs that are reachable via this interface. Just
like a switch device, it can notify the software bridge about changes
to its fdb. This patch exploits this device-to-bridge-notification and
extracts the relevant information from the hardware events to generate
notifications to an attached software bridge.

There are 2 sources for this information:
1) The reply message of Perform-Network-Subchannel-Operations (PNSO)
(operation code ADDR_INFO) reports all addresses that are currently
reachable (implemented in a later patch).
2) As long as device-to-bridge-notification is enabled, hardware will
generate address change notification events, whenever the content of
the hardware fdb changes (this patch).

The bridge_hostnotify feature (PNSO operation code BRIDGE_INFO) uses
the same address change notification events. We need to distinguish
between qeth_pnso_mode QETH_PNSO_BRIDGEPORT and QETH_PNSO_ADDR_INFO
and call a different handler. In both cases deadlocks must be
prevented, if the workqueue is drained under lock and QETH_PNSO_NONE,
when notification is disabled.

bridge_hostnotify generates udev events, there is no intend to do the same
for dev2br. Instead this patch will generate SWITCHDEV_FDB_ADD_TO_BRIDGE
and SWITCHDEV_FDB_DEL_TO_BRIDGE notifications, that will cause the
software bridge to add (or delete) entries to its fdb as 'extern_learn
offload'.

Documentation/networking/switchdev.txt proposes to add
"depends NET_SWITCHDEV" to driver's Kconfig. This is not done here,
so even in absence of the NET_SWITCHDEV module, the QETH_L2 module will
still be built, but then the switchdev notifiers will have no effect.

No VLAN filtering is done on the entries and VLAN information is not
passed on to the bridge fdb entries. This could be added later.
For now VLAN interfaces can be defined on the upper bridge interface.

Multicast entries are not passed on to the bridge fdb.
This could be added later. For now mcast flooding can be used in the
bridge.

The card reports all MACs that are in its FDB, but we must not pass on
MACs that are registered for this interface.
Signed-off-by: NAlexandra Winter <wintera@linux.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch detects whether device-to-bridge-notification, provided
by the Perform Network Subchannel Operation (PNSO) operation code
ADDR_INFO (OC3), is supported by this card. A following patch will
map this to the learning_sync bridgeport flag, so we store it in
priv->brport_hw_features in bridgeport flag format.

Only IQD cards provide PNSO.
There is a feature bit to indicate whether the machine provides OC3,
unfortunately it is not set on old machines.
So PNSO is called to find out. As this will disable notification
and is exclusive with bridgeport_notification, this must be done
during card initialisation before previous settings are restored.

PNSO functionality requires some configuration values that are added to
the qeth_card.info structure. Some helper functions are defined to fill
them out when the card is brought online and some other places are
adapted, that can also benefit from these fields.
Signed-off-by: NAlexandra Winter <wintera@linux.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add helper functions to expose Channel Subsystem ID (CSSID), MIF Image Id
(IID), Channel ID (CHID) and Channel Path ID (CHPID).
These values are required by the qeth driver's exploitation of network-
address-change-notifications to determine which entries belong to this
interface.

Store the Partition identifier in System log, as this may be used to map
a Linux view to a Hardware view for debugging purpose.
Signed-off-by: NAlexandra Winter <wintera@linux.ibm.com>
Reviewed-by: NVineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Acked-by: NHeiko Carstens <hca@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for operation code 3 (OC3) of the
Perform-Network-Subchannel-Operations (PNSO) function
of the Channel-Subsystem-Call (CHSC) instruction.

PNSO provides 2 operation codes:
OC0 - BRIDGE_INFO
OC3 - ADDR_INFO (new)

Extend the function calls to *pnso* to pass the OC and
add new response code 0108.

Support for OC3 is indicated by a flag in the css_general_characteristics.
Signed-off-by: NAlexandra Winter <wintera@linux.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: NPeter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: NVineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Acked-by: NHeiko Carstens <hca@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add CQE compression support for completions of packets that span
multiple strides in a Striding RQ, per the HW capability.
In our memory model, we use small strides (256B as of today) for the
non-linear SKB mode. This feature allows CQE compression to work also
for multiple strides packets. In this case decompressing the mini CQE
array will use stride index provided by HW as part of the mini CQE.
Before this feature, compression was possible only for single-strided
packets, i.e. for packets of size up to 256 bytes when in non-linear
mode, and the index was maintained by SW.
This feature is supported for ConnectX-5 and above.

Feature performance test:
This was whitebox-tested, we reduced the PCI speed from 125Gb/s to
62.5Gb/s to overload pci and manipulated mlx5 driver to drop incoming
packets before building the SKB to achieve low cpu utilization.
Outcome is low cpu utilization and bottleneck on pci only.
Test setup:
Server: Intel(R) Xeon(R) Silver 4108 CPU @ 1.80GHz server, 32 cores
NIC: ConnectX-6 DX.
Sender side generates 300 byte packets at full pci bandwidth.
Receiver side configuration:
Single channel, one cpu processing with one ring allocated. Cpu utilization
is ~20% while pci bandwidth is fully utilized.
For the generated traffic and interface MTU of 4500B (to activate the
non-linear SKB mode), packet rate improvement is about 19% from ~17.6Mpps
to ~21Mpps.
Without this feature, counters show no CQE compression blocks for
this setup, while with the feature, counters show ~20.7Mpps compressed CQEs
in ~500K compression blocks.
Signed-off-by: NOfer Levi <oferle@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Add support for rewriting of IPV6 DSCP part of traffic class field.
Next commands, for example, can be used to offload rewrite action:

OVS:
 $ ovs-ofctl add-flow ovs-sriov "tcpv6, in_port=REP, \
       actions=mod_nw_tos:68, output:NIC"

iproute2:
 $ tc filter add dev REP ingress protocol ipv6 prio 1 flower skip_sw \
       ip_proto tcp \
       action pedit ex munge ip6 traffic_class set 68 retain 0xfc pipe \
       action mirred egress redirect dev NIC
Signed-off-by: NMaor Dickman <maord@nvidia.com>
Reviewed-by: NRoi Dayan <roid@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Support tc trap such that packets can explicitly be forwarded to slow
path if they match a specific rule.

In the example below, we want packets with src IP equals 7.7.7.8 to be
forwarded to software, in which case it will get to the appropriate
representor net device.

$ tc filter add dev eth1 protocol ip prio 1 root flower skip_sw \
    src_ip 7.7.7.8 action trap
Signed-off-by: NEli Cohen <eli@mellanox.com>
Reviewed-by: NRoi Dayan <roid@nvidia.com>
Reviewed-by: NAriel Levkovich <lariel@nvidia.com>
Reviewed-by: NMaor Dickman <maord@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Multiple features use metadata matching such as bond vport
in live migration, multi-port RoCE mode, stacked devices;
hence, enable vport metadata matching by default.

Fixes: 1e62e222 ("net/mlx5: E-Switch, Use vport metadata matching only when mandatory")
Signed-off-by: NVu Pham <vuhuong@mellanox.com>
Reviewed-by: NBodong Wang <bodong@nvidia.com>
Reviewed-by: NRoi Dayan <roid@nvidia.com>
Reviewed-by: NParav Pandit <parav@nvidia.com>
Reviewed-by: NMark Bloch <mbloch@nvidia.com>
Reviewed-by: NOz Shlomo <ozsh@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

In merged eswitch configuration, peer miss rule is setup for all
vports. If metadata is enabled, peer miss rule with metadata matching
will be configured instead of source port matching; however, some
vports that have not yet been enabled don't have default_metadata
setup and their default_metadata will be zero.

Hence, setup/cleanup default metadata for all vports when eswitch moves
in/out of offloads mode.

Fixes: 133dcfc5 ("net/mlx5: E-Switch, Alloc and free unique metadata for match")
Signed-off-by: NVu Pham <vuhuong@mellanox.com>
Reviewed-by: NBodong Wang <bodong@nvidia.com>
Reviewed-by: NRoi Dayan <roid@nvidia.com>
Reviewed-by: NMark Bloch <mbloch@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Uplink vport must have a dedicated metadata with vhca_id
being part of the metadata.

Fixes: 133dcfc5 ("net/mlx5: E-Switch, Alloc and free unique metadata for match")
Signed-off-by: NVu Pham <vuhuong@mellanox.com>
Reviewed-by: NMark Bloch <mbloch@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Check E-Switch capabilities and enable metadata support flag
before using it to setup other features that need metadata.
Signed-off-by: NVu Pham <vuhuong@mellanox.com>
Reviewed-by: NMark Bloch <mbloch@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

LAG offload can't be enabled if the enslaved PF is not lag master,
which is indicated by HCA capabilities bit. It is cleared if more than
64 VFs are configured for this PF.

Previously, a data structure is created to store lag info, including
PFs to be enslaved, then a handler is registered for netdev notifier.
However, this initialization is skipped if PF is not lag master. So
PF can't handle CHANGEUPPER event from upper bond device. Even worse,
PF is enslaved silently, and LAG offload is not activated.

Fix this by registering netdev notifier for PFs which are not lag
masters. When CHANGEUPPER event is received, and both physical ports
(and only them) on the same NIC are about to be enslaved, a warning is
returned for user to know it.
Signed-off-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NRaed Salem <raeds@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Reviewed-by: NRaed Salem <raeds@nvidia.com>
Reviewed-by: NRoi Dayan <roid@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

If bond tx type is not active-backup or hash, LAG offload can't be
enabled. When CHANGEUPPER event is received, and both PFs (and only
them) under the same lag master are about to be enslaved, a warning
is returned for user to know the offload failure, otherwise PFs are
enslaved silently without LAG offload activated.
Signed-off-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NRaed Salem <raeds@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Reviewed-by: NRaed Salem <raeds@nvidia.com>
Reviewed-by: NRoi Dayan <roid@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Change the return value to -ENOENT, to make it more meaningful.
Signed-off-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Before calling timecounter_cyc2time(), clock->lock must be taken.
Use mlx5_timecounter_cyc2time instead which guarantees a safe access.

Fixes: afc98a0b ("net/mlx5: Update ptp_clock_event foreach PPS event")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>

Holding the clock lock is not required when scheduling a PPS work.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: NMoshe Shemesh <moshe@mellanox.com>

Fix a typo in ptp_clock_info naming: mlx5_p2p -> mlx5_ptp.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>

Clock struct is part of struct mlx5_core_dev. Code was inconsistent, on
some cases used container_of and on another used clock->mdev.

Align code to use container_of amd remove clock->mdev pointer.
While here, fix reverse xmas tree coding style.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: NMoshe Shemesh <moshe@mellanox.com>

This isn't a fall through because it was after a return statement.  The
fall through annotation leads to a Smatch warning:

    drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c:246
    mlx5e_ethtool_get_sset_count() warn: ignoring unreachable code.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NGustavo A. R. Silva <gustavoars@kernel.org>