It is possible, although unlikely, that probing will find the
phy_device for the first LMAC of a thunder BGX device, but then need
to fail with -EPROBE_DEFER on a subsequent LMAC.  In this case, we
need to call put_device() on each of the phy_devices that were
obtained, but will be unused due to returning -EPROBE_DEFER.

Also, since we can break out of the probing loop early, we need to
explicitly call of_node_put() outside of the loop.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we selected MDIO_OCTEON, which after creating the Thunder
specific MDIO bus driver is much less useful.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the code was factored out of mdio-octeon.c, the
MODULE_DESCRIPTION, MODULE_AUTHOR and MODULE_LICENSE annotations were
inadvertently omitted.  Restore them so that we don't get kernel taint
warnings upon module loading.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Locking ppp_mutex must be done before dereferencing file->private_data,
otherwise it could be modified before ppp_unattached_ioctl() takes the
lock. This could lead ppp_unattached_ioctl() to override ->private_data,
thus leaking reference to the ppp_file previously pointed to.

v2: lock all ppp_ioctl() instead of just checking private_data in
    ppp_unattached_ioctl(), to avoid ambiguous behaviour.

Fixes: f3ff8a4d ("ppp: push BKL down into the driver")
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Caesar Wang says:

====================
arc_emac: fixes the emac issues and cleanup emac drivers

This series patches are based on kernel 4.5-rc7+ version.
Linux version 4.5.0-rc7-next-20160311+ (wxt@nb) (...) #45 SMP Sun Mar 13 16:17:56

The history patch in here:
Patch-v1: https://lkml.org/lkml/2016/3/11/209
Patch-v2: https://lkml.org/lkml/2016/3/13/39

Verified on kylin board with my github.
https://github.com/Caesar-github/rockchip/tree/kylin/next

That's verified on kylin board with ubuntu os.

This series patches are built all pass with Mr.robot on
https://github.com/Caesar-github/linux/tree/build-emac-v3

How to test and verify?

You can refer to the following wiki document.
http://rockchip.wikidot.com/linux-develop-guide

bootup log:
[    1.264740] rockchip_emac 10200000.ethernet: no regulator found
[    1.270908] rockchip_emac 10200000.ethernet: ARC EMAC detected with id: 0x7fd02
[    1.278362] rockchip_emac 10200000.ethernet: IRQ is 29
[    1.283747] rockchip_emac 10200000.ethernet: MAC address is now 06:5d:61:c7:39:41
[    1.291314] rockchip_emac 10200000.ethernet: GPIO lookup for consumer phy-reset
[    1.291333] rockchip_emac 10200000.ethernet: using device tree for GPIO lookup
[    1.663155] rockchip_emac 10200000.ethernet: connected to Generic PHY phy with id 0xffffc816
[    8.863448] rockchip_emac 10200000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off

root@localhost:/# busybox ping www.baidu.com
PING www.baidu.com (14.215.177.38): 56 data bytes
64 bytes from 14.215.177.38: seq=0 ttl=48 time=35.046 ms
64 bytes from 14.215.177.38: seq=1 ttl=48 time=35.095 ms
64 bytes from 14.215.177.38: seq=2 ttl=48 time=34.203 ms
64 bytes from 14.215.177.38: seq=3 ttl=48 time=38.516 ms
...
---

1) This series has 6 patches: (1--->9)
net: arc_emac: make the rockchip emac document more compatible
net: arc_emac: add phy reset is optional for device tree
net: arc_emac: support the phy reset for emac driver
net: arc: trivial: cleanup the emac driver
clk: rockchip: add node-id for rk3036 emac hclk
clk: rockchip: associate the rk3036 HCLK_EMAC clock-id
clk: rockchip: add clock-id for rk3036 emac pll source clock
clk: rockchip: associate SCLK_MAC_PLL and disable reparenting on rk3036
ARM: dts: rockchip: add support emac for RK3036

2) This series patches have the following descriptions:

Hi Rob, David:
PATCH[1/9-2/9]: ====>
net: arc_emac: make the rockchip emac document more compatible
net: arc_emac: add phy reset is optional for device tree

The patches change the rockchip emac document for more compatible and
Add the phy reset property for document.
---

Hi David
PATCH[3/9]: ====>
net: arc_emac: support the phy reset for emac driver

The emac didn't work on kylin board since in some case the clocks parent changed.
The kylin hardware connects the phy reset pin, we should use it with real world.
As the previous patch discuss on https://patchwork.kernel.org/patch/8186801/

And as sergei/Heiko suggestions on
https://patchwork.kernel.org/patch/8564571/
---

Hi David
PATCH[4/9]: ====>
net: arc: trivial: cleanup the emac driver

The first time to look the emac drivers, I think that have to cleanup the drivers with scripts.
Although it's the trivial things, in order to be more read.
---

Hi Heiko,Michael,Stephen:
PATCH[5/9-8/9]: ====> clk: rockchip: rk3036: fix and add node id for emac clock

Four-part from https://patchwork.kernel.org/patch/8564581/
clk: rockchip: add node-id for rk3036 emac hclk
clk: rockchip: associate the rk3036 HCLK_EMAC clock-id
clk: rockchip: add clock-id for rk3036 emac pll source clock
clk: rockchip: associate SCLK_MAC_PLL and disable reparenting on rk3036

Add the emac needed clocks for rk3036 SoCs
---

Hi Heiko:
PATCH[9/9]: ====>
ARM: dts: rockchip: add support emac for RK3036

Add the emac needed main info for rk3036 dts.
---

Thanks your reviewing! :)

Changes in v3:
- %s/he/the
- Add the Cc people
- As Sergei comments, the original name is better, so
  %s/reset-gpios/phy-reset-gpios
- Add the Cc people.
- Caused the build error since the missing include head file.
- %s/reset/phy-reset to match the device tree.
- Add the Cc people
- Add the Cc people.
- Add the Cc people.
- Add the Cc people.
- Add the Cc people.
- Add the Cc people.
- rename reset-gpio to phy-reset-gpios.
- change the commit.
- remove the pcfg_output_high, that's really not needed for emac.
- Add the Cc people.
- Fixes the 'zhengxing' to 'Xing Zheng'.

Changes in v2:
- change the commit and remove the repeat the name 'rockchip'.
- %s/phy-reset-gpios/reset-gpios
- As the pervious version, Sergei and Heiko comments on
  https://patchwork.kernel.org/patch/8564571/.
- Nevermind, add signed-off since Heiko the original patch,
  refer the Heiko's test patch on
  https://github.com/mmind/linux-rockchip/commit/a943c588783438ff1c508dfa8c79f1709aa5775e
  :)
- As the robot notice the build error since overflow in implicit
  constant conversion.
- rename phy-reset-gpio to reset-gpios.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the emac device node for rk3036 SoCs.
We need to let mac clock under the DPLL which is able to provide
the accurate 50MHz what mac_ref need, since that will cause some
unstable things if the cpufreq is working.
Signed-off-by: NXing Zheng <zhengxing@rock-chips.com>
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Cc: linux-rockchip@lists.infradead.org
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The emac needs constant and very specific rate but the possible PLL-sources
are very limited, so we expect the PLL source to be set manually on per
board and don't want it to get changed in an automatic way later.
So add the necessary clock-id and disable reparenting on set_rate calls.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Suitable PLLs for the emac on the rk3036 are difficult to find
and one of them is the (continuously changing) APLL. So in most
cases it will be necessary to select a PLL manually.
So add a clock-id for it.
Signed-off-by: NXing Zheng <zhengxing@rock-chips.com>
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Associate the new clock id the clock.
Signed-off-by: NXing Zheng <zhengxing@rock-chips.com>
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the node-id for the emac hclk to the binding header.
Signed-off-by: NXing Zheng <zhengxing@rock-chips.com>
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch will make the driver more readability

The emac has the error and warnings if you run
'scripts/checkpatch.pl -f --subjective xxx' to check.

Let's clean up such trivial details.
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Kochetkov <al.kochet@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds to support the emac phy reset.

Different boards may require different phy reset duration. Add property
phy-reset-duration for emac driver, so that the boards that need
a longer reset duration can specify it in their device tree.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Alexander Kochetkov <al.kochet@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the following property for arc_emac.

1) phy-reset-gpios:
The phy-reset-gpio is an optional property for arc emac device tree boot.
Change the binding document to match the driver code.

2) phy-reset-duration:
Different boards may require different phy reset duration. Add property
phy-reset-duration for device tree probe, so that the boards that need
a longer reset duration can specify it in their device tree.

Anyway, we can add the above property for arc emac.
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc; Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the rk3036 SoCs to match driver for document since the emac driver
has supported the rk3036 SoCs.

This patch adds the rk3036/rk3066/rk3188 SoCS to compatible for rockchip
emac ducument. Also, that will suit for other SoCs in the future.
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the ETHTOOL_GLINKSETTINGS implementation finds that userland is
using the wrong number of words of link mode bitmaps (or is trying to
find out the right numbers) it sets the cmd field to 0 in the response
structure.

This is inconsistent with the implementation of every other ethtool
command, so let's remove that inconsistency before it gets into a
stable release.

Fixes: 3f1ac7a7 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API")
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Iff  sh_eth_phy_start() call fails in sh_eth_open(), the netif_start_queue()
call done by sh_eth_dev_init()  is not undone.  In order to deal with that,
stop calling netif_start_queue()  from there, so that it can be called only
when the device is fully opened and sh_eth_dev_init() only deals with the
hardware initialization, symmetrically to sh_eth_dev_exit()...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When driver has hit a parity event, HW can no longer write to host memory.
As a result, Tx completions cannot be written to the host SB memory, and
waiting for Tx completions eventually timeout.
As driver is willing to delay as much as 1-2 seconds per Tx queue for its
draining and this delay is sequential, the time to recover might greatly
lengthen needlessly in case the recovery is done under multi-connection
traffic.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

local_bh_disable() + spin_lock() is equivalent to spin_lock_bh(), same for
the unlock/enable case, so replace the calls by the appropriate wrappers.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS/OVS updates for net-next

The following patchset contains Netfilter/IPVS fixes and OVS NAT
support, more specifically this batch is composed of:

1) Fix a crash in ipset when performing a parallel flush/dump with
   set:list type, from Jozsef Kadlecsik.

2) Make sure NFACCT_FILTER_* netlink attributes are in place before
   accessing them, from Phil Turnbull.

3) Check return error code from ip_vs_fill_iph_skb_off() in IPVS SIP
   helper, from Arnd Bergmann.

4) Add workaround to IPVS to reschedule existing connections to new
   destination server by dropping the packet and wait for retransmission
   of TCP syn packet, from Julian Anastasov.

5) Allow connection rescheduling in IPVS when in CLOSE state, also
   from Julian.

6) Fix wrong offset of SIP Call-ID in IPVS helper, from Marco Angaroni.

7) Validate IPSET_ATTR_ETHER netlink attribute length, from Jozsef.

8) Check match/targetinfo netlink attribute size in nft_compat,
   patch from Florian Westphal.

9) Check for integer overflow on 32-bit systems in x_tables, from
   Florian Westphal.

Several patches from Jarno Rajahalme to prepare the introduction of
NAT support to OVS based on the Netfilter infrastructure:

10) Schedule IP_CT_NEW_REPLY definition for removal in
    nf_conntrack_common.h.

11) Simplify checksumming recalculation in nf_nat.

12) Add comments to the openvswitch conntrack code, from Jarno.

13) Update the CT state key only after successful nf_conntrack_in()
    invocation.

14) Find existing conntrack entry after upcall.

15) Handle NF_REPEAT case due to templates in nf_conntrack_in().

16) Call the conntrack helper functions once the conntrack has been
    confirmed.

17) And finally, add the NAT interface to OVS.

The batch closes with:

18) Cleanup to use spin_unlock_wait() instead of
    spin_lock()/spin_unlock(), from Nicholas Mc Guire.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The spin_lock()/spin_unlock() is synchronizing on the
nf_conntrack_locks_all_lock which is equivalent to
spin_unlock_wait() but the later should be more efficient.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

On loaded TCP servers, looking at millions of sockets can hold
cpu for many seconds, if the lookup condition is very narrow.

(eg : ss dst 1.2.3.4 )

Better add a cond_resched() to allow other processes to access
the cpu.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The smc91x driver defines a macro that compares its argument to
itself, apparently to get a true result while using its argument
to avoid a warning about unused local variables.

Unfortunately, this triggers a warning with gcc-6, as the comparison
is obviously useless:

drivers/net/ethernet/smsc/smc91x.c: In function 'smc_hardware_send_pkt':
drivers/net/ethernet/smsc/smc91x.c:563:14: error: self-comparison always evaluates to true [-Werror=tautological-compare]
  if (!smc_special_trylock(&lp->lock, flags)) {

This replaces the macro with another one that behaves similarly,
with a cast to (void) to ensure the argument is used, and using
a literal 'true' as its value.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend OVS conntrack interface to cover NAT.  New nested
OVS_CT_ATTR_NAT attribute may be used to include NAT with a CT action.
A bare OVS_CT_ATTR_NAT only mangles existing and expected connections.
If OVS_NAT_ATTR_SRC or OVS_NAT_ATTR_DST is included within the nested
attributes, new (non-committed/non-confirmed) connections are mangled
according to the rest of the nested attributes.

The corresponding OVS userspace patch series includes test cases (in
tests/system-traffic.at) that also serve as example uses.

This work extends on a branch by Thomas Graf at
https://github.com/tgraf/ovs/tree/nat.
Signed-off-by: NJarno Rajahalme <jarno@ovn.org>
Acked-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NJoe Stringer <joe@ovn.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

There is no need to help connections that are not confirmed, so we can
delay helping new connections to the time when they are confirmed.
This change is needed for NAT support, and having this as a separate
patch will make the following NAT patch a bit easier to review.
Signed-off-by: NJarno Rajahalme <jarno@ovn.org>
Acked-by: NJoe Stringer <joe@ovn.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Repeat the nf_conntrack_in() call when it returns NF_REPEAT.  This
avoids dropping a SYN packet re-opening an existing TCP connection.
Signed-off-by: NJarno Rajahalme <jarno@ovn.org>
Acked-by: NJoe Stringer <joe@ovn.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Add a new function ovs_ct_find_existing() to find an existing
conntrack entry for which this packet was already applied to.  This is
only to be called when there is evidence that the packet was already
tracked and committed, but we lost the ct reference due to an
userspace upcall.

ovs_ct_find_existing() is called from skb_nfct_cached(), which can now
hide the fact that the ct reference may have been lost due to an
upcall.  This allows ovs_ct_commit() to be simplified.

This patch is needed by later "openvswitch: Interface with NAT" patch,
as we need to be able to pass the packet through NAT using the
original ct reference also after the reference is lost after an
upcall.
Signed-off-by: NJarno Rajahalme <jarno@ovn.org>
Acked-by: NJoe Stringer <joe@ovn.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Only a successful nf_conntrack_in() call can effect a connection state
change, so it suffices to update the key only after the
nf_conntrack_in() returns.

This change is needed for the later NAT patches.
Signed-off-by: NJarno Rajahalme <jarno@ovn.org>
Acked-by: NJoe Stringer <joe@ovn.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

This makes the code easier to understand and the following patches
more focused.
Signed-off-by: NJarno Rajahalme <jarno@ovn.org>
Acked-by: NJoe Stringer <joe@ovn.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

NAT checksum recalculation code assumes existence of skb_dst, which
becomes a problem for a later patch in the series ("openvswitch:
Interface with NAT.").  Simplify this by removing the check on
skb_dst, as the checksum will be dealt with later in the stack.
Suggested-by: NPravin Shelar <pshelar@nicira.com>
Signed-off-by: NJarno Rajahalme <jarno@ovn.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Remove the definition of IP_CT_NEW_REPLY from the kernel as it does
not make sense.  This allows the definition of IP_CT_NUMBER to be
simplified as well.
Signed-off-by: NJarno Rajahalme <jarno@ovn.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Vivien Didelot says:

====================
net: dsa: finer bridging control

This patchset renames the bridging routines of the DSA layer, make the
unbridging routine return void, and rework the DSA netdev notifier handler,
similar to what the Mellanox Spectrum driver does.

Changes RFC -> v1:
  - drop unused NETDEV_PRECHANGEUPPER case
  - add Andrew's Tested-by tag
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rework the netdev event handler, similar to what the Mellanox Spectrum
driver does, to easily welcome more events later (for example
NETDEV_PRECHANGEUPPER) and use netdev helpers (such as
netif_is_bridge_master).
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netdev_upper_dev_unlink() which notifies NETDEV_CHANGEUPPER, returns
void, as well as del_nbp(). So there's no advantage to catch an eventual
error from the port_bridge_leave routine at the DSA level.

Make this routine void for the DSA layer and its existing drivers.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename DSA port_join_bridge and port_leave_bridge routines to
respectively port_bridge_join and port_bridge_leave in order to respect
an implicit Port::Bridge namespace.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to figure 39 in PEB3086 data sheet, version 1.4 this indication
replaces DR when layer 1 transition source state is F6.

This fixes mISDN layer 1 getting stuck in F6 state in TE mode on
Dialogic Diva 2.02 card (and possibly others) when NT deactivates it.
Signed-off-by: NMaciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It looks like IPAC/ISAC chips register defines weren't in any particular
order.

Order them by their number to make it easier to spot holes.
Signed-off-by: NMaciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the local variable intializers in the driver turned out to be
pointless,  kill 'em.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Gregory CLEMENT says:

====================
Few mvneta fixes

In this second version I split the last patch in two parts as
requested.

For the record the initial cover letter was:
"here is a patch set of few fixes. Without the first one, a kernel
configured with debug features ended to hang when the driver is built
as a module and is removed. This is quite is annoying for debugging!

The second patch fix a forgotten flag at the initial submission of the
driver.

The third patch is only really a cosmetic one so I have no problem to
not apply it for 4.5 and wait for 4.6.

I really would like to see the first one applied for 4.5 and for the
second I let you judge if it something needed for now or that should
wait the next release."
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some literal values are actually already defined by macros, so let's use
them.

[gregory.clement@free-electrons.com: split intial commit in two
individual changes]
Signed-off-by: NDmitri Epshtein <dima@marvell.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit corrects error printing when shutting down the port.

[gregory.clement@free-electrons.com: split initial commit in two
individual changes]
Signed-off-by: NDmitri Epshtein <dima@marvell.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>