While AR_PHY_CCA_NOM_VAL_* does contain the expected internal noise floor
for a chip measured in clean air, it refers to the lowest expected reading.

Depending on the frequency, this measurement can vary by about 6db, thus
causing a higher reported channel noise and signal strength.

Factor in the 6db offset when converting internal noisefloor to channel noise.

This patch makes the reported values more accurate for all chips without
affecting NF calibration behavior.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were using wrong IRQ number so clearing wasn't working at all.
Depending on a platform this could result in a one device having two
interrupts assigned. On BCM4706 this resulted in all IRQs being broken.

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: stable@vger.kernel.org
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Assign the training power for PAPRD based on the chip.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a HW capability to indicate whether PAPRD is enabled
for the card, since PAPRD could be enabled in the EEPROM, but
disabled in the driver. This makes things clearer.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Retraining of PAPRD based on agc2_pwr is required for
chips other than AR9485.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Remove unneeded memset.

  All the values in the PAPRD gain table are filled, so there
  is no need to zero out the arrays.

* Use GFP_KERNEL in ar9003_paprd_create_curve

  This is called from the PAPRD work, so the atomic variant
  is not needed.

* Change return type of ar9003_paprd_setup_gain_table
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the PowerSave wrappers outside ath_paprd_activate(),
since they are already being used in ath_paprd_calibrate().
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The PAPRD training control registers have to be
programmed with values that depend on the chip. This patch
ensures that the correct values are chosen for the chip
in use.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Various PAPRD registers are at addresses that are different
from those for the rest of the chips in the AR9003 family.
Fix them.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Trying to access the OTP memory on the AR9340
causes a data bus error like this:

  Data bus error, epc == 86e84164, ra == 86e84164
  Oops[#1]:
  Cpu 0
  $ 0   : 00000000 00000061 deadc0de 00000000
  $ 4   : b8115f18 00015f18 00000007 00000004
  $ 8   : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c
  $12   : 7c7c3c7c 001f0041 00000000 7c7c7c3c
  $16   : 86ee0000 00015f18 00000000 00000007
  $20   : 00000004 00000064 00000004 86d71c44
  $24   : 00000000 86e6ca00
  $28   : 86d70000 86d71b20 86ece0c0 86e84164
  Hi    : 00000000
  Lo    : 00000064
  epc   : 86e84164 ath9k_hw_wait+0x58/0xb0 [ath9k_hw]
      Tainted: G           O
  ra    : 86e84164 ath9k_hw_wait+0x58/0xb0 [ath9k_hw]
  Status: 1100d403    KERNEL EXL IE
  Cause : 4080801c
  PrId  : 0001974c (MIPS 74Kc)
  Modules linked in: ath9k(O+) ath9k_common(O) ath9k_hw(O) ath(O) ar934x_nfc
  mac80211(O) usbcore usb_common scsi_mod nls_base nand nand_ecc nand_ids
  crc_ccitt cfg80211(O) compat(O) arc4 aes_generic crypto_blkcipher cryptomgr
  aead crypto_hash crypto_algapi ledtrig_timer ledtrig_default_on leds_gpio
  Process insmod (pid: 459, threadinfo=86d70000, task=87942140, tls=779ac440)
  Stack : 802fb500 000200da 804db150 804e0000 87816130 86ee0000 00010000 86d71b88
          86d71bc0 00000004 00000003 86e9fcd0 80305300 0002c0d0 86e74c50 800b4c20
          000003e8 00000001 00000000 86ee0000 000003ff 86e9fd64 80305300 80123938
          fffffffc 00000004 000058bc 00000000 86ea0000 86ee0000 000001ff 878d6000
          99999999 86e9fdc0 86ee0fcc 86e9e664 0000c0d0 86ee0000 0000700000007000
          ...
  Call Trace:
  [<86e84164>] ath9k_hw_wait+0x58/0xb0 [ath9k_hw]
  [<86e9fcd0>] ath9k_hw_setup_statusring+0x16b8/0x1c7c [ath9k_hw]

  Code: 0000a812  0040f809  00000000 <00531024> 1054000b  24020001  0c05b5dc  2404000a  26520001

The cause of the error is that the OTP register
offsets are different on the AR9340 than the
actually used values.

Cc: <stable@vger.kernel.org> # 3.0+
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

D-Link DWA-125/B1 is a relatively new USB Wi-Fi adapter, using a
Ralink chipset supported by the rt2800usb driver. Currently, to work
around the problem (it's missing in all present kernel versions,
up to and including 3.7.x), I had to add this to /etc/rc.local:

echo 2001 3c1e >> /sys/bus/usb/drivers/rt2800usb/new_id

After that, the device works without problems. Been using it for over
a week with no bugs in sight.

The attached patch is trivial and simply adds the new USB ID to the
list of devices handled by rt2800usb.
Signed-off-by: NMaia Kozheva <sikon@ubuntu.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use WARN rather than printk followed by WARN_ON(1), for conciseness.
Signed-off-by: NCong Ding <dinggnu@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a regression which was introduced by:
"carl9170: split up carl9170_handle_mpdu"

Previously, the ieee80211_rx_status was kept on the
stack of carl9170_handle_mpdu. Now it's passed into
the function as a pointer parameter. Hence, the old
memcpy call needs to be fixed.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This device can be found on some embedded devices connected to a
Broadcom SoC like the BCM4718.
I tested this with my Netgear WNDR3400 v1.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As described in the documentation of bcma_wflush16 in drivers/net
/wireless/brcm80211/brcmsmac/types.h some PCIe controllers of Broadcom
SoCs are broken. The PCIe controller on these SoCs are mostly used to
connect some additional wifi device to the SoC and some of these wifi
devices are supported by brcmsmac.
For my BCM43224 connected to the broken PCIe controller of the BCM4718 I
need an extra read after write in brcms_b_write_objmem() to prevent a
Data bus error. This fixes the problem reading tsf_random later.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit "ath9k: Fix the 'xmit' debugfs file" changed the
the array size of ath_stats.txstats to IEEE80211_NUM_ACS,
which is wrong because the HW queue number is used to
update the statistics. Revert back to using ATH9K_NUM_TX_QUEUES.
Reported-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Recent versions of udev cause synchronous firmware loading from the
probe routine to fail because the request to user space times out.
The original fix for b43legacy (commit a3ea2c76) moved the firmware
load from the probe routine to a work queue, but it still used synchronous
firmware loading. This method is OK when b43legacy is built as a module;
however, it fails when the driver is compiled into the kernel.

This version changes the code to load the initial firmware file
using request_firmware_nowait(). A completion event is used to
hold the work queue until that file is available. The remaining
firmware files are read synchronously.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>  (V3.4+)
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for bcma wifi core revision 17 which is found on
BCM4716/4717/4718 SoCs. The firmware version 610.812 for brcmsmac found
in linux-firmware does not support these cores, but a firmware
generated with b43-fwcutter from the proprietary broadcom wireless
driver works with these chips. This wifi core contains a revision 5
N-PHY and a revision 7 radio of type 0x2056.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit f74b9d36.

Turns out reverting commit a240dc7b
"ath9k_hw: Updated AR9003 tx gain table for 5GHz" was not enough to
bring the tx power back to normal levels on devices like the
Buffalo WZR-HP-G450H, this one needs to be reverted as well.

This revert improves tx power by ~10 db on that device
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Cc: rmanohar@qca.qualcomm.com
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Get rid of WL_CONN(...) macro in favor of brcmf_dbg(CONN,...)
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Get rid of WL_SCAN(...) macro in favor of brcmf_dbg(SCAN,...)
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Get rid of WL_TRACE(...) macro in favor of brcmf_dbg(TRACE,...)
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Get rid of WL_INFO() in favor of brcmf_dbg(INFO,...).
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Getting rid of wl_cfg80211 specific error log macro.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The source file wl_cfg80211.c has its own debug macros and levels.
This patch maps the macros to the ones used in the rest of the
brcmfmac driver.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The call to brcmf_dbg(ERROR, ...) only resulted in a log message
when compiled with -DDEBUG. Error messages are valuable for resolving
issues so this patch replaces it with brcmf_err(...) so they always
end up in the log.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, adding a new event requires modification in two source
files. Use macro definition to have one place and have better
maintainability.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using gcc v4.7.2 gave following warning:

  CC [M]  drivers/net/wireless/brcm80211/brcmsmac/aiutils.o
brcmsmac/aiutils.c: In function 'ai_deviceremoved':
brcmsmac/aiutils.c:733:9: error: 'w' may be used uninitialized
in this function [-Werror=uninitialized]

Inspection of the pci_read_config_dword() function showed it can
return without modifying the output variable 'w' so this patch
initializes it to 0.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rework the bus interface between common driver part and bus-specific
driver part. It prepares for adding tracing in bus-specific callback
functions.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: users@rt2x00.serialmonkey.com (moderated for non-subscribers)
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>