Add a fat_msg_ratelimit() to limit the message generation rate.
Signed-off-by: NNamjae Jeon <linkinjeon@gmail.com>
Signed-off-by: NAmit Sahrawat <amit.sahrawat83@gmail.com>
Acked-by: NOGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently FAT file-system maps the VFS "superblock" abstraction to the
FSINFO block.  The FSINFO block contains non-essential data about the
amount of free clusters and the next free cluster.  FAT file-system can
always find out this information by scanning the FAT table, but having it
in the FSINFO block may speed things up sometimes.  So FAT file-system
relies on the VFS superblock write-out services to make sure the FSINFO
block is written out to the media from time to time.

The whole "superblock write-out" VFS infrastructure is served by the
'sync_supers()' kernel thread, which wakes up every 5 (by default) seconds
and writes out all dirty superblock using the '->write_super()' call-back.
 But the problem with this thread is that it wastes power by waking up the
system every 5 seconds no matter what.  So we want to kill it completely
and thus, we need to make file-systems to stop using the '->write_super'
VFS service, and then remove it together with the kernel thread.

This patch switches the FAT FSINFO block management from
'->write_super()'/'->s_dirt' to 'fsinfo_inode'/'->write_inode'.  Now,
instead of setting the 's_dirt' flag, we just mark the special
'fsinfo_inode' inode as dirty and let VFS invoke the '->write_inode'
call-back when needed, where we write-out the FSINFO block.

This patch also makes sure we do not mark the 'fsinfo_inode' inode as
dirty if we are not FAT32 (FAT16 and FAT12 do not have the FSINFO block)
or if we are in R/O mode.

As a bonus, we can also remove the '->sync_fs()' and '->write_super()' FAT
call-back function because they become unneeded.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Preparation for further changes.  It touches few functions in fatent.c and
prevents them from marking the superblock as dirty unnecessarily often.
Namely, instead of marking it as dirty in the internal tight loops - do it
only once at the end of the functions.  And instead of marking it as dirty
while holding the FAT table lock, do it outside the lock.

The reason for this patch is that marking the superblock as dirty will
soon become a little bit heavier operation, so it is cleaner to do this
only when it is necessary.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A preparation patch which introduces a 'mark_fsinfo_dirty()' helper
function which just sets the 's_dirt' flag to 1 so far.  I'll add more
code to this helper later, so I do not mark it as 'inline'.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is patchset makes fatfs stop using the VFS '->write_super()' method
for writing out the FSINFO block.

The final goal is to get rid of the 'sync_supers()' kernel thread.  This
kernel thread wakes up every 5 seconds (by default) and calls
'->write_super()' for all mounted file-systems.  And the bad thing is that
this is done even if all the superblocks are clean.  Moreover, some
file-systems do not even need this end they do not register the
'->write_super()' method at all (e.g., btrfs).

So 'sync_supers()' most often just generates useless wake-ups and wastes
power.  I am trying to make all file-systems independent of
'->write_super()' and plan to remove 'sync_supers()' and '->write_super'
completely once there are no more users.

The '->write_supers()' method is mostly used by baroque file-systems like
hfs, udf, etc.  Modern file-systems like btrfs and xfs do not use it.
This justifies removing this stuff from VFS completely and make every FS
self-manage own superblock.

Tested with xfstests.

This patch:

Preparation for further changes.  It introduces a special inode
('fsinfo_inode') in FAT file-system which we'll later use for managing the
FSINFO block.  Note, this there is already one special inode ('fat_inode')
which is used for managing the FAT tables.

Introduce new 'MSDOS_FSINFO_INO' constant for this special inode.  It is
safe to do because FAT file-system does not store inode numbers on the
media but generates them run-time.

I've also cleaned up the comment to existing 'MSDOS_ROOT_INO' constant,
while on it.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The PRINTK() macro isn't really used.  Let's just remove it because it
is ugly and out of date.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are two cases that the cache flush is needed to avoid data loss
against unexpected hang or power failure.  One is sync file function (i.e.
 nilfs_sync_file) and another is checkpointing ioctl.

This issues a cache flush request to device for such cases if barrier
mount option is enabled, and makes sure data really is on persistent
storage on their completion.
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As described in commit 07d106d0 ("vfs: fix up ENOIOCTLCMD error
handling"), drivers should return -ENOIOCTLCMD if they receive an ioctl
command which they don't understand.  Doing so will result in -ENOTTY
being returned to userspace, which matches the behaviour of the compat
layer if it fails to translate an ioctl command.

This patch fixes the pipe ioctl to return -ENOIOCTLCMD instead of -EINVAL
when passed an unknown ioctl command.
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: NAlan Cox <alan@linux.intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The init/mount.o source files produce a number of sparse warnings of the
type:

warning: incorrect type in argument 1 (different address spaces)
   expected char [noderef] <asn:1>*dev_name
   got char *name

This is due to the syscalls expecting some of the arguments to be user
pointers but they are being passed as kernel pointers.  This is harmless
but adds a lot of noise to a sparse build.

To limit the noise just disable the sparse checking in the relevant source
files, but still display a warning so that the user knows this has been
done.

Since the sparse checking has been disabled we can also remove the __user
__force casts that are scattered thru the source.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Suggest the shorter pr_<level> instead of printk(KERN_<LEVEL>.

Prefer to use pr_<level> over bare printks.
Prefer to use pr_warn over pr_warning.
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Requires --strict option during invocation:
	~/linux$ scripts/checkpatch --strict foo.patch

This tests for a bad habits of mine like this:

	return 0 ;

Note that it does allow a special case of a bare semicolon
for empty loops:

	while (foo())
		;
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Previous code was using optimizations which were developed to work well
even on narrow-word CPUs (by today's standards).  But Linux runs only on
32-bit and wider CPUs.  We can use that.

First: using 32x32->64 multiply and trivial 32-bit shift, we can correctly
divide by 10 much larger numbers, and thus we can print groups of 9 digits
instead of groups of 5 digits.

Next: there are two algorithms to print larger numbers.  One is generic:
divide by 1000000000 and repeatedly print groups of (up to) 9 digits.
It's conceptually simple, but requires an (unsigned long long) /
1000000000 division.

Second algorithm splits 64-bit unsigned long long into 16-bit chunks,
manipulates them cleverly and generates groups of 4 decimal digits.  It so
happens that it does NOT require long long division.

If long is > 32 bits, division of 64-bit values is relatively easy, and we
will use the first algorithm.  If long long is > 64 bits (strange
architecture with VERY large long long), second algorithm can't be used,
and we again use the first one.

Else (if long is 32 bits and long long is 64 bits) we use second one.

And third: there is a simple optimization which takes fast path not only
for zero as was done before, but for all one-digit numbers.

In all tested cases new code is faster than old one, in many cases by 30%,
in few cases by more than 50% (for example, on x86-32, conversion of
12345678).  Code growth is ~0 in 32-bit case and ~130 bytes in 64-bit
case.

This patch is based upon an original from Michal Nazarewicz.

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NDenys Vlasenko <vda.linux@googlemail.com>
Cc: Douglas W Jones <jones@cs.uiowa.edu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The '%p' output of the kernel's vsprintf() uses spec.field_width to
determine how many digits to output based on 2 * sizeof(void*) so that all
digits of a pointer are shown.  ie.  a pointer will be output as
"001A2B3C" instead of "1A2B3C".  However, if the '#' flag is used in the
format (%#p), then the code doesn't take into account the width of the
'0x' prefix and will end up outputing "0x1A2B3C" instead of "0x001A2B3C".

This patch reworks the "pointer()" format hook to include 2 characters for
the '0x' prefix if the '#' flag is included.

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NColin Cross <ccross@android.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the module-wide pr_fmt() mechanism rather than open-coding "genirq: "
everywhere.

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sethostname() and setdomainname() notify userspace on failure (without
modifying uts_kern_table).  Change things so that we only notify userspace
on success, when uts_kern_table was actually modified.
Signed-off-by: NSasikantha babu <sasikanth.v19@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: WANG Cong <amwang@redhat.com>
Reviewed-by: NCyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so it
wasn't converted by 44c10138 ("PCI: Change all drivers to use
pci_device->revision").

In one case, it even reads PCI revision ID without using it -- that code
is now removed...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Cc: Eric Moore <eric.moore@lsi.com>
Acked-by: NAuke Kok <auke-jan.h.kok@intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the comment of allocate_resource(), the explanation of parameter max
and min is not correct.

Actually, these two parameters are used to specify the range of the
resource that will be allocated, not the min/max size that will be
allocated.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ULONG_MAX is often used to check for integer overflow when calculating
allocation size.  While ULONG_MAX happens to work on most systems, there
is no guarantee that `size_t' must be the same size as `long'.

This patch introduces SIZE_MAX, the maximum value of `size_t', to improve
portability and readability for allocation size validation.
Signed-off-by: NXi Wang <xi.wang@gmail.com>
Acked-by: NAlex Elder <elder@dreamhost.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add the new kmalloc_array() to the list of general-purpose memory
allocators in chapter 14.
Signed-off-by: NXi Wang <xi.wang@gmail.com>
Acked-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NPekka Enberg <penberg@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit d065bd81 ("mm: retry page fault when blocking on disk
transfer") and commit 37b23e05 ("x86,mm: make pagefault killable")
introduced changes into the x86 pagefault handler for making the page
fault handler retryable as well as killable.

These changes reduce the mmap_sem hold time, which is crucial during OOM
killer invocation.

Port these changes to um.
Signed-off-by: NKautuk Consul <consul.kautuk@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This allocation may be large.  The code is probing to see if it will
succeed and if not, it falls back to vmalloc().  We should suppress any
page-allocation failure messages when the fallback happens.
Reported-by: NDave Jones <davej@redhat.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

rtc-s3c.c:673:32: warning: `s3c_rtc_drv_data_array' defined but not used [-Wunused-variable]
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the devres managed resource functions in the probe routine.  Also
affects the remove routine where the previously used free and release
functions are not needed.

The devm_* functions eliminate the need for manual resource releasing and
simplify error handling.  Resources allocated by devm_* are freed
automatically on driver detach.
Signed-off-by: NHannu Heikkinen <ext-hannu.m.heikkinen@nokia.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove RTT interrupt handling, since PIE mode interrupts are now better
emulated in generic code via an hrtimer we have no need for this, and
there is no codepath in the driver that enables these periodic interrupts
anyway.
Signed-off-by: NRajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Adds device tree support for rtc-lpc32xx.c
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the rtc reports the time might be invalid due to oscillator failure,
M41T93_FLAG_OF flag must not be reset by get_time() as the read operation
doesn't make the time valid.

Without this patch, only the first get_time() reported an invalid time,
the second get_time() reported a valid time althought the reported time is
probably wrong due to oscillator failure.

Instead of resetting in get_time(), with this patch M41T93_FLAG_OF is
reset in set_time() when a valid time is to be written.
Signed-off-by: NNikolaus Voss <n.voss@weinmann.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some DS13XX devices have "trickle chargers".  Its configuration register
is at different locations, the setup is the same, though.  Since the
configuration is board specific, introduce a platform_data to this driver.
Tested with a DS1339 on a custom board.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ds1307 was kzalloced, so no need to zero members of the struct.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In order to keep consistency with other rtc drivers,rename CONFIG_RTC_MXC
to CONFIG_RTC_DRV_MXC.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
[akpm@linux-foundation.org: fix missed arch/arm/configs/imx_v6_v7_defconfig]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

RTC_DRV_IMXDI and RTC_MXC are on-chip RTC modules, so move them under
"on-CPU RTC drivers" selection menu.

While at it change the dependency of RTC_DRV_IMXDI from ARCH_MX25 to
SOC_IMX25.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Changes are based on arch/cris/arch-v10/drivers/pcf8563.c

[akpm@linux-foundation.org: fix sparse warning]
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mikael Starvik <starvik@axis.com>
Acked-by: NJesper Nilsson <jesper.nilsson@axis.com>
Cc: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently there is no generic way to get the RTC battery status within an
application.  So add an ioctl to read the status bit.  The idea is that
the bit is set once a low voltage is detected.  It stays there until it is
reset using the RTC_VL_CLR ioctl.
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use module_platform_driver() to remove the boilerplate code.

Also, change the probe and remove functions to __devinit/__devexit.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SPEAr platforms now support DT and so must convert all drivers support DT.
This patch adds DT probing support for rtc and updates its documentation
too.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Cc: Rob Herring <robherring2@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

number()'s behaviour is slighly changed: 0 becomes "0" instead of "00"
when using the flag SPECIAL and base 8.

Before:
Number\Format  %o    %#o  %x    %#x
            0     0   00    0   0x0
            1     1   01    1   0x1
           16    20  020   10  0x10

After:
Number\Format  %o    %#o  %x    %#x
            0     0    0    0   0x0
            1     1   01    1   0x1
           16    20  020   10  0x10
Signed-off-by: NPierre Carrier <pierre@spotify.com>
Acked-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We are not preallocating a sufficient number of nodes.
Signed-off-by: NNick Piggin <npiggin@kernel.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a spinlock warning is printed we usually get

 BUG: spinlock bad magic on CPU#0, modprobe/111
  lock: 0xdff09f38, .magic: 00000000, .owner: /0, .owner_cpu: 0

but it's nicer to print the symbol for the lock if we have it so that we
can avoid 'grep dff09f38 /proc/kallsyms' to find out which lock it was.
Use kallsyms to print the symbol name so we get something a bit easier to
read

 BUG: spinlock bad magic on CPU#0, modprobe/112
  lock: test_lock, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0

If the lock is not in kallsyms %ps will fall back to printing the address
directly.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Using %ps in a printk format will sometimes fail silently and print the
empty string if the address passed in does not match a symbol that
kallsyms knows about.  But using %pS will fall back to printing the full
address if kallsyms can't find the symbol.  Make %ps act the same as %pS
by falling back to printing the address.

While we're here also make %ps print the module that a symbol comes from
so that it matches what %pS already does.  Take this simple function for
example (in a module):

	static void test_printk(void)
	{
		int test;
		pr_info("with pS: %pS\n", &test);
		pr_info("with ps: %ps\n", &test);
	}

Before this patch:

 with pS: 0xdff7df44
 with ps:

After this patch:

 with pS: 0xdff7df44
 with ps: 0xdff7df44
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>