commit 21a4e469 (netdev: ethernet dev_alloc_skb to netdev_alloc_skb)
should have used "ndev" instead of "dev".

This causes the following build errors:

drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_rx':
drivers/net/ethernet/freescale/fec.c:714: error: 'dev' undeclared (first use in this function)
drivers/net/ethernet/freescale/fec.c:714: error: (Each undeclared identifier is reported only once
drivers/net/ethernet/freescale/fec.c:714: error: for each function it appears in.)
drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_alloc_buffers':
drivers/net/ethernet/freescale/fec.c:1213: error: 'dev' undeclared (first use in this function)

Fix it, so that fec driver can be built again.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
  - Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: NPradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the bug that we got wrong phy_name on imx6q sabrelite board.
snprintf used wrong length of phy_name.
phy_name length is MII_BUS_ID_SIZE + 3 rather not MII_BUS_ID_SIZE.
I change it to sizeof(phy_name).
Signed-off-by: NRichard Zhao <richard.zhao@linaro.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using module_platform_driver can make the code smaller.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when the link is 10 Mbps and the mode is RMII, it's necessary
to set FRCONT to 1 in MIIGSK_CFGR to divide the RMII source
clock by 10 in order to support 10 Mbps operations.
Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Auditing all usage of ethtool_ops found several drivers that
are not declaring the struct const when it should be.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On extensive NFS boots on a mx6qsabrelite board it was noted that "FEC: MDIO read timeout" were occuring,
which caused failure on loading the FEC driver.

The original FEC_MII_TIMEOUT was set to 1 ms, which is too low when passed to the usecs_to_jiffies macro.

On ARM one jiffy is 10ms, so use a timeout of 30ms, which corresponds to 3 jiffies.

After running extensive NFS boots, the MDIO timeouts do not occur anymore with this change.
Signed-off-by: NRogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's for migrating to generic clk framework API.
Signed-off-by: NRichard Zhao <richard.zhao@linaro.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>

The .remove code is broken in several ways.
 - mdiobus_unregister() is called twice for the same object in case of dual FEC
 - phy_disconnect() is being called when the PHY is already disconnected
 - the requested IRQ(s) are not freed
 - fec_stop() is being called with the inteface already stopped

 All of those lead to kernel crashes if the remove function is actually used.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Additionally to setting the ETHER_EN bit in FEC_ECNTRL the MII/RMII
setting in FEC_R_CNTRL needs to be preserved to keep the MII interface
functional.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the MAC address is supplied via platform_data it should be OK as
it is and should not be modified in case of a dual FEC setup.
Also copying the MAC from platform_data to the single 'macaddr'
variable will overwrite the MAC for the first interface in case of a
dual FEC setup.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

prevent calling request_irq() with a known invalid IRQ number and
preserve the return value of the platform_get_irq() function
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon detection of a FDX/HDX change the interface is restarted twice.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The con_id is actually not needed for clk_get().
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- remove some bogus whitespace
 - remove line wraps from printk messages
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pdev->id is used in several places for different purpose.  All
these uses assume it's always the id of fec device which is >= 0.
However this is only true for non-DT case.  When DT plays, pdev->id
is always -1, which will break these pdev->id users.

Instead of fixing all these users one by one, this patch introduces
a new member 'dev_id' to 'struct fec_enet_private' for holding the
correct fec device id, and replaces all the existing uses of pdev->id
with this dev_id.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add poll controller function for fec nic.
Signed-off-by: NXiao Jiang <jgq516@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't use hardcoded irq num and replace it with
FEC_IRQ_NUM macro.
Signed-off-by: NXiao Jiang <jgq516@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The imx6q enet is a derivative of imx28 enet controller.  It fixed
the frame endian issue found on imx28, and added 1 Gbps support.

It also fixes a typo on vendor name in Kconfig.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function fec_enet_mii_init(), it uses non-zero pdev->id as part
of the condition to check the second fec instance (fec1).  This works
before the driver supports device tree probe.  But in case of device
tree probe, pdev->id is -1 which is also non-zero, so the logic becomes
broken when device tree probe gets supported.

The patch change the logic to check "pdev->id > 0" as the part of the
condition for identifying fec1.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FEC can work without a phy reset on some platforms, which means not
very platform necessarily have a phy-reset gpio encoded in device tree.
Even on the platforms that have the gpio, FEC can work without
resetting phy for some cases, e.g. boot loader has done that.

So it makes more sense to have the phy-reset-gpio request failure as
a debug message rather than a warning, and get fec_reset_phy() return
void since the caller does not check the return anyway.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replace it by ndo_set_rx_mode
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the Freescale drivers into drivers/net/ethernet/freescale/ and
make the necessary Kconfig and Makefile changes.

CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Shlomi Gridish <gridish@freescale.com>
CC: Li Yang <leoli@freescale.com>
CC: Pantelis Antoniou <pantelis.antoniou@gmail.com>
CC: Vitaly Bordug <vbordug@ru.mvista.com>
CC: Dan Malek <dmalek@jlc.net>
CC: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It adds device tree probe support for fec driver.
Signed-off-by: NJason Liu <jason.hui@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NDavid S. Miller <davem@davemloft.net>

On the recent i.mx (mx25/50/53), there is a gasket inside fec
controller which needs to be enabled no matter phy works in MII
or RMII mode.

The current code enables the gasket only when phy interface is RMII.
It's broken when the driver works with a MII phy.  The patch uses
platform_device_id to distinguish the SoCs that have the gasket and
enables it on these SoCs for both MII and RMII mode.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Reported-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: NDavid S. Miller <davem@davemloft.net>

There is no need to check for the address being a multicast address in
the netdev_for_each_mc_addr loop, so remove it. This patch covers all
remaining network drivers still containing such a check.

Cc: Joe Perches <joe@perches.com>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch has been tested on the Freescale M5234BCC, which includes the
National Semiconductor DP83640 with IEEE 1588 support.

Cc: Greg Ungerer <gerg@uclinux.org>
Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

The platform_device_id table is supposed to be zero-terminated.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Apart from not being used the first argument isn't even a struct
platform_device *.
Reported-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Also optimize not to reread the value written to FEC_R_CNTRL.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Reported-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

This fixes warnings when CONFIG_DMA_API_DEBUG=y:

	NULL NULL: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x000000004781a020] [size=64 bytes]
	net eth0: DMA-API: device driver frees DMA memory with different size [device address=0x000000004781a020] [map size=2048 bytes] [unmap size=64 bytes]

Moreover pass the platform device to dma_{,un}map_single which makes
more sense because the logical network device doesn't know anything
about dma.

Passing the platform device was a suggestion by Lothar Waßmann.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

A few of these were found and reported by Lothar Waßmann.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

A variable named "dev" usually (usually subjective) points to a struct
device.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

This undoes the effects of phy_start in fec_enet_open.
Reported-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Moreover stop listing all i.MX platforms featuring a FEC, and use
the platform's config symbol that selects registration of a fec device
instead.  This might make it easier to add new platforms.

Set default = y for ARMs having a fec to reduce defconfig sizes.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Saving it first into struct net_device->base_addr (which is an unsigned
long) is pointless and only needs to use more casts than necessary.
Reported-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>