- 10 12月, 2011 2 次提交
-
-
由 Nikolay Martynov 提交于
It looks like the regression was introduced between 20111202 and 20111205 (linux-next tree). Symptoms: connection to AP seem to be established, but no data goes though it in any way. Tested on intel 5300. Peek at the changes have shown that it looks like at least part of the code wasn't merged properly. It was originally committed into iwl_agn.c but code in question was moved to iwl-mac80211.c. This patch puts code in place and my card works again. Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
CC [M] drivers/net/wireless/wl12xx/tx.o drivers/net/wireless/wl12xx/tx.c: In function ‘wl1271_tx_fill_hdr’: drivers/net/wireless/wl12xx/tx.c:288:6: warning: ‘tx_attr’ may be used uninitialized in this function Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 08 12月, 2011 14 次提交
-
-
由 Luciano Coelho 提交于
-
由 Eyal Shapira 提交于
The user can pass broadcast SSID (ssid="") in the list of SSIDs for active scan. In this case the loop was attempting to match SSIDs in the filter list to this empty entry and marking them as HIDDEN (sending probe request) by mistake Signed-off-by: NEyal Shapira <eyal@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Eliad Peller 提交于
wl1271_tm_cmd_interrogate creates a reply skb, but doesn't send it (and thus just leaks it). Add the missing cfg80211_testmode_reply() call. Signed-off-by: NEliad Peller <eliad@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Eliad Peller 提交于
During plt init we configure some redundant commands, which are not needed for plt (specifically, we shouldn't configure any role-specific params, as there are no active roles). remove them. Signed-off-by: NEliad Peller <eliad@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Eliad Peller 提交于
fix several issues in testmode test/interrogate commands: 1. check the driver state is not OFF. 2. wakeup the chip from elp (if needed) 3. fix memory leak in wl1271_tm_cmd_interrogate() Signed-off-by: NEliad Peller <eliad@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Johannes Berg 提交于
This code has been on the list to remove for a long time, so disable it by default, add a warning to its Kconfig, and schedule it for removal in 3.5. The only known dependency, hal, has not required it since its 0.5.12 release, which was in early 2009 and hal has since been deprecated completely. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Nikolay Martynov 提交于
Enable ANI for ar9100 since it seems to be working fine (and as a matter of fact ANI was always performed for ar9100 since code which was supposed to disable it didn't achieve this goal). This patch sets config.enable_ani to default (true) value for ar9100. Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Nikolay Martynov 提交于
Currently in ath9k code there is an attempt which is meant to disable ANI for ar9100 and ar9340. But it doesn't really achieve this. All it does is disable ANI init and setup (i.e. calls to ath9k_hw_ani_setup and ath9k_hw_ani_init). Since ath9k_hw_ani_setup is not called ah->config.ani_poll_interval is never initialized (i.e. it is always zero) and ath_ani_calibrate always executes ANI procedures (over uninitialized ANI parameters). Moreover, ath_ani_calibrate is being called each 1ms because common->ani.timer is set to zero interval because ah->config.ani_poll_interval==0 (and thus smallest value of all intervals). Normally it should not be called this often. This patch changes the code so config.enable_ani is used to check if ANI should be performed. config.enable_ani is initialized to true by default. This patch sets it to false for ar9100 and ar9340. Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Nikolay Martynov 提交于
To help debugging write a log entry when long calibration, short calibration or ANI is performed. Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Nikolay Martynov 提交于
Add missed space and change typo in calibration debugging log. Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
Recently more places in mac80211 call drv_flush to ensure proper order for state changes wrt. powersave, channel changes, etc. On some systems such calls lead to spurious logspam about failing to stop tx dma, as well as hardware resets that go along with that. Instead of dropping packets in a place where it's completely unnecessary, only do it when drop == true. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
Turning off the radio when mac80211 tells the driver that it's idle is not a good idea, as idle interfaces might still occasionally scan or send packets. The only time the radio can be safely turned off is when drv_stop has been called. In the mean time, use sc->ps_idle only to indicate network sleep vs full sleep. Move the LED GPIO changes out of the PCI suspend/resume path, the start/stop functions already take care of that. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
After waking up from full sleep, registers are accessible, but rx/tx typically fails. A fast channel change will not recover from this, so ensure that a full-sleep -> wake transition is always followed by a full reset. The reason why this hasn't created any serious problems yet is that it's hidden by the (wrong) behavior of enabling/disabling the radio when the wiphy idle state changes. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 07 12月, 2011 24 次提交
-
-
由 Ben Greear 提交于
AP interfaces routinely call this logic, so just silently return when this happens instead of splatting the kernel logs. Reported-by: NChristian Lamparter <chunkeey@googlemail.com> Signed-off-by: NBen Greear <greearb@candelatech.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
Some cores are mapped in the fixed way, they registers can be accessed all the time. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Arik's patch "mac80211: allow action frames with unknown BSSID in GO mode" allowed any action frames in P2P mode to go through, but only to cooked monitor interfaces as the IEEE80211_RX_RA_MATCH was still cleared. As a result my no-monitor patches broke invitation responses. Instead of allowing any action frames in P2P GO mode to go through with a wrong BSSID like that patch did, allow all public action frames. They will never be processed by mac80211, but can be reported via nl80211 then. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This fixes another regression from my "pass all fragments to driver at once" patches -- if the packet is being retransmitted then we don't go through all handlers, but we still need to move it to the skbs list, otherwise we run into the first warning in __ieee80211_tx() and leak the skb. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Don Fry 提交于
Move the notification structures for ucode operations from the iwl_priv structure to the iwl_shared structure, with associated code changes. Signed-off-by: NDon Fry <donald.h.fry@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Don Fry 提交于
Move the ucode_type variable from the iwl_priv to the iwl_shared structure with associated code changes. Signed-off-by: NDon Fry <donald.h.fry@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Don Fry 提交于
Replace the references to the iwl_priv structure with the iwl_trans structure as the priv structure is never referenced other than to access the trans structure. Rename from iwlagn to iwl. Signed-off-by: NDon Fry <donald.h.fry@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Don Fry 提交于
iwl-agn-ucode is generic ucode operations, not limited just to iwlagn. Signed-off-by: NDon Fry <donald.h.fry@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wey-Yi Guy 提交于
The file dealing with all the operations through testmode, rename it. Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hsu, Kenny 提交于
Create new tm command for WOWLAN uCode loading to support further debugging function in userspace. - IWL_TM_CMD_APP2DEV_LOAD_WOWLAN_FW Signed-off-by: NKenny Hsu <kenny.hsu@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Using the actual shifted constants here allows one to read and or them more easily. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This is only used for TX debugging where there already is more debugging and tracing is more useful anyway, so remove it. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This debug level is unused, remove it. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This macro is unused right now. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wey-Yi Guy 提交于
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hsu, Kenny 提交于
Use generic chunk size of dumpit packet for all necessary testmode commands instead of add declaration individually. Signed-off-by: NKenny Hsu <kenny.hsu@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kenny Hsu 提交于
The size of sram may alter according to ucode type. Retrieve the maximum sram size by current ucode type for range checking to prevent wrong data access. Signed-off-by: NKenny Hsu <kenny.hsu@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hsu, Kenny 提交于
Create new testmode commands and attributes to suppot sram data reading. Because the amount of sram data may exceed single skb packet size. Using the nl80211 dump it funtion to deliver sram data to userspace. - IWL_TM_CMD_APP2DEV_READ_SRAM - IWL_TM_CMD_APP2DEV_DUMP_SRAM - IWL_TM_ATTR_SRAM_ADDR - IWL_TM_ATTR_SRAM_SIZE - IWL_TM_ATTR_SRAM_DUMP Signed-off-by: NKenny Hsu <kenny.hsu@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohammed Shafi Shajakhan 提交于
max_streams for AR9462 is '2'. it does not fixes anything, but improves the code readability Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohammed Shafi Shajakhan 提交于
based on systems change to improve rx dynamic range, and enables heavy clip for 5G HT40 MCS0 to improve spectral mask power. also remove an unused function declaration Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
A previous commit fixed a problem whereby the rtl8192c driver loaded the firmware from disk many times; however, the log message was not moved. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Alexander Simon 提交于
The HT mode is set by iw (previous patchsets). The interface is set into the specified HT mode. HT mode and capabilities are announced in beacons. If we add a station that uses HT also, the fastest matching HT mode will be used for transmission. That means if we are using HT40+ and we add a station running on HT40-, we would transfer at HT20. If we join an IBSS with HT40, but the secondary channel is not available, we will fall back into HT20 as well. Allow frame aggregation to start in IBSS mode. Signed-off-by: NAlexander Simon <an.alexsimon@googlemail.com> [siwu@hrz.tu-chemnitz.de: Updates] * remove implicit channel_type enum assumptions * use rate_control_rate_init() if channel type changed * remove channel flags check * activate HT IBSS feature support * slightly reword commit message * rebase on wireless-testing Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Reviewed-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Simon Wunderlich 提交于
* Follow 802.11n-2009 9.13.3.1 for protection mode and ADDBA * Send ADDBA only to HT STAs - implement 11.5.1.1 partially Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Reviewed-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Alexander Simon 提交于
Prepare cfg80211 for IBSS HT: * extend cfg80211 ibss struct with channel_type * Check if extension channel can be used * Export can_beacon_sec_chan for use in mac80211 (will be called from ibss.c later). Signed-off-by: NAlexander Simon <an.alexsimon@googlemail.com> [siwu@hrz.tu-chemnitz.de: Updates] * fix cfg80211_can_beacon_ext_chan comment * remove implicit channel_type enum assumptions * remove radar channel flags check * add HT IBSS feature flag * reword commit message Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Reviewed-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-