Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <chris@printf.net>

Add support for non-blocking request, pre_req() runs dma_map_sg() and
post_req() runs dma_unmap_sg(). This patch can increase card read/write
speed, especially for high speed card and slow CPU(for some embedded
platform).

Users can get a great benefit from this patch. if CPU frequency is 800MHz,
SDR104 or DDR50 card read/write speed may increase more than 15%.

test results:
intel i3(800MHz - 2.3GHz), SD card clock 208MHz

performance mode(2.3GHz):
Before:
dd if=/dev/mmcblk0p1 of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 1.18191 s, 56.8 MB/s
After:
 dd if=/dev/mmcblk0p1 of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 1.09276 s, 61.4 MB/s

powersave mode(800MHz):
Before:
dd if=/dev/mmcblk0p1 of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 1.29569 s, 51.8 MB/s
After:
dd if=/dev/mmcblk0p1 of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 1.11218 s, 60.3 MB/s
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NChris Ball <chris@printf.net>

The new phase searching method is more concise and easier to
understand.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NChris Ball <chris@printf.net>

If the host driver removed while card in the slot, the host will not
power off card power correctly. This bug is produced because host
eject flag set before the last mmc_set_ios callback, we should set the
eject flag after power off.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NChris Ball <chris@printf.net>

Add support for realtek rts5250 pci card reader. The card reader has
some problems with DDR50 mode, so add a new quirks2 for broken ddr50.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NChris Ball <chris@printf.net>

This patch adds the erase capability to OMAP1/OMAP2420 MMC driver. Idea is
the same than in commit 93caf8e6 ("omap_hsmmc: add erase capability") that we
disable the data timeout interrupt for erases.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NChris Ball <chris@printf.net>

Because use_dma is set only in mmc_omap_probe and unset nowhere there is no
need to carry that flag in struct mmc_omap_host for mmc_omap_prepare_data
function.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NChris Ball <chris@printf.net>

Simplify probe and cleanup code by using devm_ioremap_resource. This also
makes probe code to follow more common allocate private struct followed by
other initialization style.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NChris Ball <chris@printf.net>

Field mem_res in struct mmc_omap_host is used only once in mmc_omap_probe
when setting the phys_base field so we may just se the phys_base straight
and remove needless mem_res.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NChris Ball <chris@printf.net>

host-irq is set twice so remove needless one.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NChris Ball <chris@printf.net>

Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NChris Ball <chris@printf.net>

Omap MMC driver initialization can cause a NULL pointer dereference in
tasklet_hi_action on Nokia N810 if its miniSD cover is open during driver
initialization.

[    1.070000] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[    1.080000] pgd = c0004000
[    1.080000] [00000000] *pgd=00000000
[    1.080000] Internal error: Oops: 80000005 [#1] PREEMPT ARM
[    1.080000] Modules linked in:
[    1.080000] CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 3.13.0-rc2+ #95
[    1.080000] Workqueue: events menelaus_work
[    1.080000] task: c7863340 ti: c7878000 task.ti: c7878000
[    1.080000] PC is at 0x0
[    1.080000] LR is at tasklet_hi_action+0x68/0xa4
...
[    1.080000] [<c003543c>] (tasklet_hi_action+0x68/0xa4) from [<c0034dd0>] (__do_softirq+0xbc/0x208)
[    1.080000] [<c0034dd0>] (__do_softirq+0xbc/0x208) from [<c003521c>] (irq_exit+0x84/0xac)
[    1.080000] [<c003521c>] (irq_exit+0x84/0xac) from [<c00135cc>] (handle_IRQ+0x64/0x84)
[    1.080000] [<c00135cc>] (handle_IRQ+0x64/0x84) from [<c000859c>] (omap2_intc_handle_irq+0x54/0x68)
[    1.080000] [<c000859c>] (omap2_intc_handle_irq+0x54/0x68) from [<c0015be0>] (__irq_svc+0x40/0x74)
[    1.080000] Exception stack(0xc7879d70 to 0xc7879db8)
[    1.080000] 9d60:                                     000003f1 0000000a 00000009 0000001c
[    1.080000] 9d80: c7879e70 c780bc10 c780bc10 00000000 00000001 00008603 c780bc78 c7879e4e
[    1.080000] 9da0: 00000002 c7879db8 c00343b0 c0160c9c 20000113 ffffffff
[    1.080000] [<c0015be0>] (__irq_svc+0x40/0x74) from [<c0160c9c>] (__aeabi_uidiv+0x20/0x9c)
[    1.080000] [<c0160c9c>] (__aeabi_uidiv+0x20/0x9c) from [<c00343b0>] (msecs_to_jiffies+0x18/0x24)
[    1.080000] [<c00343b0>] (msecs_to_jiffies+0x18/0x24) from [<c01ec3ec>] (omap_i2c_xfer+0x30c/0x458)
[    1.080000] [<c01ec3ec>] (omap_i2c_xfer+0x30c/0x458) from [<c01e9724>] (__i2c_transfer+0x3c/0x74)
[    1.080000] [<c01e9724>] (__i2c_transfer+0x3c/0x74) from [<c01eac4c>] (i2c_transfer+0x78/0x94)
[    1.080000] [<c01eac4c>] (i2c_transfer+0x78/0x94) from [<c01eb0bc>] (i2c_smbus_xfer+0x3c0/0x4f8)
[    1.080000] [<c01eb0bc>] (i2c_smbus_xfer+0x3c0/0x4f8) from [<c01eb414>] (i2c_smbus_write_byte_data+0x34/0x3c)
[    1.080000] [<c01eb414>] (i2c_smbus_write_byte_data+0x34/0x3c) from [<c01bb308>] (menelaus_write_reg+0x1c/0x40)
[    1.080000] [<c01bb308>] (menelaus_write_reg+0x1c/0x40) from [<c01bb904>] (menelaus_work+0xa0/0xc4)
[    1.080000] [<c01bb904>] (menelaus_work+0xa0/0xc4) from [<c00439c4>] (process_one_work+0x1fc/0x334)
[    1.080000] [<c00439c4>] (process_one_work+0x1fc/0x334) from [<c0043d6c>] (worker_thread+0x244/0x380)
[    1.080000] [<c0043d6c>] (worker_thread+0x244/0x380) from [<c0049d04>] (kthread+0xc0/0xd4)
[    1.080000] [<c0049d04>] (kthread+0xc0/0xd4) from [<c0012758>] (ret_from_fork+0x14/0x3c)
[    1.080000] Code: bad PC value
[    1.090000] ---[ end trace 7bc2fc7cd14f1d95 ]---
[    1.100000] Kernel panic - not syncing: Fatal exception in interrupt

Reason for this is that omap_notify_cover_event which calls
tasklet_hi_schedule gets called before struct cover_tasklet is initialized.

Call to omap_notify_cover_event on Nokia N810 happens from menelaus.c PMIC
driver via board-n8x0.c during execution of mmc_add_host in case of open
miniSD cover.

Fix this by moving cover_timer and cover_tasklet initialization before
mmc_add_host call in mmc_omap_new_slot.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NChris Ball <chris@printf.net>

This patch adds DT support for r8a7791.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NChris Ball <chris@printf.net>

This patch updates r8a7790 DT data to have SoC specific settings.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NChris Ball <chris@printf.net>

This patch updates r8a7779 DT data to have SoC specific settings.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NChris Ball <chris@printf.net>

This patch updates r8a7778 DT data to have SoC specific settings.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NChris Ball <chris@printf.net>

It is easier to read if sh_mobile_sdhi_of_cfg and
sh_mobile_sdhi_of_match are closer.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NChris Ball <chris@printf.net>

There are no reason to why the use of a non-volatile internal eMMC
cache should be controlled by a host cap. Instead let's just enable it
if the eMMC card supports it.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <chris@printf.net>

Earlier we disabled the cache during suspend, which meant a flush was
internally at the eMMC performed as well.

To simplify code we can make use of the mmc_flush_cache(), during mmc
suspend, which makes the mmc_cache_ctrl() redundant so then we can
remove it.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <chris@printf.net>

There are no active users of this host capability. The primary reason
for adding this cap was due to a bug in ux500 boot loader code, which
is not a relevant issue any more. So, let's remove it.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

There is no need for keeping a host cap for MMC_CAP2_SANITIZE, instead
we just make the feature default available.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Due to the removal of the Kconfig option MMC_UNSAFE_RESUME, several
validations of a present bus_ops callback became redundant. Let's
remove these.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Invoking system suspend or shutdown without using the Kconfig option
MMC_UNSAFE_RESUME, did trigger an ungraceful power cut of the card.

To improve the situation, change the behavior to always make use of the
available bus_ops callbacks that handles system suspend and shutdown
properly.

By changing the behavior MMC_UNSAFE_RESUME becomes redundant, so lets's
remove it.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Since the users of the exported PM functions are now using the modern
PM ops macros, we can convert to the proper corresponding PM configs.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <chris@printf.net>

Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <chris@printf.net>

Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <chris@printf.net>

While we are at it, don't do kmap() under kmap_atomic(), *especially*
for a page we'd allocated with GFP_KERNEL.  It's spelled "page_address",
and had that been more than that, we'd have a real trouble - kmap_high()
can block, and doing that while holding kmap_atomic() is a Bad Idea(tm).
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.

drivers/built-in.o: In function `dw_wdt_drv_probe':
drivers/watchdog/dw_wdt.c:302: undefined reference to `devm_ioremap_resource'
Signed-off-by: NRichard Weinberger <richard@nod.at>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Remove use of regmap_irq_get_virq() in driver probe which was
conflicting with use of platform_get_irq_byname().
platform_get_irq_byname() already returns the VIRQ number due
to MFD core translation so using regmap_irq_get_virq() on that
returned value results in an incorrect IRQ being requested.
The driver probes then fail because of this.
Signed-off-by: NAdam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

When memory allocation failed, drive should return error as ENOMEM.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commit c420619d "pinctrl: pinconf: remove checks on ops->pin_config_get"
removed the check on (ops != NULL) when performing pinconf_pins_show() or
pinconf_groups_show(). As these entries are always enabled, even if
pinconf is not supported, reading will result in an oops due to NULL
ops.

Instead of checking for ops, remove the corresponding debugfs entries if
pinconf and/or pinmux are not implemented.

Tested on OMAP3 (pinctrl-single).

Cc: stable@vger.kernel.org
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

the evergreen CS parser has allowed this for a while, just port
the code to the r600 one.

This is required before geom shaders can be made work.

v2: agd5f: minor cleanup and add additional 7xx reg.
Signed-off-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

I totally sign inverted my way out of this one.

Cc: stable@vger.kernel.org
Reported-by: N"Sabrina Dubroca" <sd@queasysnail.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

These page pointers shouldn't be visible to TTM in the first place, but
until we fix that up, don't clear the page metadata because that
will upset the exporter.
Reported-and-tested-by: NCristoph Haag <haagch.christoph@googleemail.com>
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>

When an eject request is sent to an ejected ACPI device, the following
panic occurs:

 ACPI: \_SB_.SCK3.CPU3: ACPI_NOTIFY_EJECT_REQUEST event
 BUG: unable to handle kernel NULL pointer dereference at 0000000000000070
 IP: [<ffffffff813a7cfe>] acpi_device_hotplug+0x10b/0x33b
	:
 Call Trace:
 [<ffffffff813a24da>] acpi_hotplug_work_fn+0x1c/0x27
 [<ffffffff8109cbe5>] process_one_work+0x175/0x430
 [<ffffffff8109d7db>] worker_thread+0x11b/0x3a0

This is becase device->handler is NULL in acpi_device_hotplug().
This case was used to fail in acpi_hotplug_notify_cb() as the target
had no acpi_deivce.  However, acpi_device now exists after ejection.

Added a check to verify if acpi_device->handler is valid for an
eject request in acpi_hotplug_notify_cb().  Note that handler passed
from an argument is still valid while acpi_device->handler is NULL.

Fixes: 202317a5 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace)
Signed-off-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Commit drm/ttm: ttm object security fixes for render nodes introduced a
regression where, if a TTM object was opened multiple times from the same
open file, the caller would spin uninterruptibly in the kernel.

Fix this.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>

One of the error paths in vmw_setup_otable_base causes us to return with
'ret' having never been set to anything causing us to return whatever was
on the stack.

Found with Coverity
Signed-off-by: NDave Jones <davej@fedoraproject.org>
Reviewed-by: NThomas Hellstrom <thellstrom@vmware.com>

When a context is first referenced in the command stream, make sure that all
scrubbed (as a result of eviction) bindings are re-emitted. Also make sure that
all bound resources are put on the resource validate list.

This is needed for legacy emulation, since legacy user-space drivers will
typically not re-emit shader bindings. It also removes the requirement for
user-space drivers to re-emit render-target- and texture bindings.

Makes suspend and hibernate now also work with legacy user-space drivers on
guest-backed devices.

v2: Don't rebind on legacy devices.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>

GB aware mesa userspace drivers are detected by the fact that they are
calling the vmw getparam ioctl querying DRM_VMW_PARAM_HW_CAPS to detect
whether the device is Guest-backed object capable. For other drivers,
lie about hardware version and send the 3D capabilities in a format they
expect.

v2:
Use DRM_VMW_PARAM_MAX_MOB_MEMORY to detect gb awareness,
Make sure we don't ovwerwrite bounce buffer or write past user-space buffer
indicated size.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>

Command stream legacy shader creation and destruction is replaced by
NOPs in the command stream, and instead guest-backed shaders are created
and destroyed as part of the command validation process.

v2: Removed some stray debug messages.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>