Enable Generic Receive Offload in the ibmvnic driver.
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Various fixes

This patchset contains various small fixes for mlxsw.

Patch #1 fixes a warning generated by switchdev core when the driver
fails to insert an MDB entry in the commit phase.

Patches #2-#4 fix a warning in check_flush_dependency() that can be
triggered when a work item in a WQ_MEM_RECLAIM workqueue tries to flush
a non-WQ_MEM_RECLAIM workqueue.

It seems that the semantics of the WQ_MEM_RECLAIM flag are not very
clear [1] and that various patches have been sent to remove it from
various workqueues throughout the kernel [2][3][4] in order to silence
the warning.

These patches do the same for the workqueues created by mlxsw that
probably should not have been created with this flag in the first place.

Patch #5 fixes a regression where an IP address cannot be assigned to a
VRF upper due to erroneous MAC validation check. Patch #6 adds a test
case.

Patch #7 adjusts Spectrum-2 shared buffer configuration to be compatible
with Spectrum-1. The problem and fix are described in detail in the
commit message.

Please consider patches #1-#5 for 5.0.y. I verified they apply cleanly.

[1] https://patchwork.kernel.org/patch/10791315/
[2] Commit ce162bfb ("mac80211_hwsim: don't use WQ_MEM_RECLAIM")
[3] Commit 39baf103 ("IB/core: Fix use workqueue without WQ_MEM_RECLAIM")
[4] Commit 75215e5b ("iwcm: Don't allocate iwcm workqueue with WQ_MEM_RECLAIM")
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Spectrum-1, when a multicast packet is admitted to the shared buffer
it increases the quotas of all the ports and {port, TC} to which it is
forwarded to.

The above means that multicast packets are accounted multiple times in
the shared buffer and can therefore cause the associated shared buffer
pool to fill up very quickly.

To work around this issue, commit e83c045e ("mlxsw:
spectrum_buffers: Configure MC pool") added a dedicated multicast pool
in which multicast packets are accounted.

The issue is not present in Spectrum-2, but in order to be backward
compatible with Spectrum-1, its default behavior is to allow a multicast
packet to increase multiple egress quotas instead of one.

Until the new (non-backward compatible) mode is supported, configure a
dedicated multicast pool as in Spectrum-1.

Fixes: fe099bf6 ("mlxsw: spectrum_buffers: Add Spectrum-2 shared buffer configuration")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test that it is possible to set an IP address on a VRF and that it is
not vetoed.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 74bc9939 ("mlxsw: spectrum_router: Veto unsupported RIF MAC
addresses") enabled the driver to veto router interface (RIF) MAC
addresses that it cannot support.

This check should only be performed for interfaces for which the driver
actually configures a RIF. A VRF upper is not one of them, so ignore it.

Without this patch it is not possible to set an IP address on the VRF
device and use it as a loopback.

Fixes: 74bc9939 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NAlexander Petrovskiy <alexpe@mellanox.com>
Tested-by: NAlexander Petrovskiy <alexpe@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The workqueue is used to periodically update the networking stack about
activity / statistics of various objects such as neighbours and TC
actions.

It should not be called as part of memory reclaim path, so remove the
WQ_MEM_RECLAIM flag.

Fixes: 3d5479e9 ("mlxsw: core: Remove deprecated create_workqueue")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ordered workqueue is used to offload various objects such as routes
and neighbours in the order they are notified.

It should not be called as part of memory reclaim path, so remove the
WQ_MEM_RECLAIM flag. This can also result in a warning [1], if a worker
tries to flush a non-WQ_MEM_RECLAIM workqueue.

[1]
[97703.542861] workqueue: WQ_MEM_RECLAIM mlxsw_core_ordered:mlxsw_sp_router_fib6_event_work [mlxsw_spectrum] is flushing !WQ_MEM_RECLAIM events:rht_deferred_worker
[97703.542884] WARNING: CPU: 1 PID: 32492 at kernel/workqueue.c:2605 check_flush_dependency+0xb5/0x130
...
[97703.542988] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
[97703.543049] Workqueue: mlxsw_core_ordered mlxsw_sp_router_fib6_event_work [mlxsw_spectrum]
[97703.543061] RIP: 0010:check_flush_dependency+0xb5/0x130
...
[97703.543071] RSP: 0018:ffffb3f08137bc00 EFLAGS: 00010086
[97703.543076] RAX: 0000000000000000 RBX: ffff96e07740ae00 RCX: 0000000000000000
[97703.543080] RDX: 0000000000000094 RSI: ffffffff82dc1934 RDI: 0000000000000046
[97703.543084] RBP: ffffb3f08137bc20 R08: ffffffff82dc18a0 R09: 00000000000225c0
[97703.543087] R10: 0000000000000000 R11: 0000000000007eec R12: ffffffff816e4ee0
[97703.543091] R13: ffff96e06f6a5c00 R14: ffff96e077ba7700 R15: ffffffff812ab0c0
[97703.543097] FS: 0000000000000000(0000) GS:ffff96e077a80000(0000) knlGS:0000000000000000
[97703.543101] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[97703.543104] CR2: 00007f8cd135b280 CR3: 00000001e860e003 CR4: 00000000003606e0
[97703.543109] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[97703.543112] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[97703.543115] Call Trace:
[97703.543129] __flush_work+0xbd/0x1e0
[97703.543137] ? __cancel_work_timer+0x136/0x1b0
[97703.543145] ? pwq_dec_nr_in_flight+0x49/0xa0
[97703.543154] __cancel_work_timer+0x136/0x1b0
[97703.543175] ? mlxsw_reg_trans_bulk_wait+0x145/0x400 [mlxsw_core]
[97703.543184] cancel_work_sync+0x10/0x20
[97703.543191] rhashtable_free_and_destroy+0x23/0x140
[97703.543198] rhashtable_destroy+0xd/0x10
[97703.543254] mlxsw_sp_fib_destroy+0xb1/0xf0 [mlxsw_spectrum]
[97703.543310] mlxsw_sp_vr_put+0xa8/0xc0 [mlxsw_spectrum]
[97703.543364] mlxsw_sp_fib_node_put+0xbf/0x140 [mlxsw_spectrum]
[97703.543418] ? mlxsw_sp_fib6_entry_destroy+0xe8/0x110 [mlxsw_spectrum]
[97703.543475] mlxsw_sp_router_fib6_event_work+0x6cd/0x7f0 [mlxsw_spectrum]
[97703.543484] process_one_work+0x1fd/0x400
[97703.543493] worker_thread+0x34/0x410
[97703.543500] kthread+0x121/0x140
[97703.543507] ? process_one_work+0x400/0x400
[97703.543512] ? kthread_park+0x90/0x90
[97703.543523] ret_from_fork+0x35/0x40

Fixes: a3832b31 ("mlxsw: core: Create an ordered workqueue for FIB offload")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NSemion Lisyansky <semionl@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EMAD workqueue is used to handle retransmission of EMAD packets that
contain configuration data for the device's firmware.

Given the workers need to allocate these packets and that the code is
not called as part of memory reclaim path, remove the WQ_MEM_RECLAIM
flag.

Fixes: d965465b ("mlxsw: core: Fix possible deadlock")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver cannot guarantee in the prepare phase that it will be able to
write an MDB entry to the device. In case the driver returned success
during the prepare phase, but then failed to add the entry in the commit
phase, a WARNING [1] will be generated by the switchdev core.

Fix this by doing the work in the prepare phase instead.

[1]
[  358.544486] swp12s0: Commit of object (id=2) failed.
[  358.550061] WARNING: CPU: 0 PID: 30 at net/switchdev/switchdev.c:281 switchdev_port_obj_add_now+0x9b/0xe0
[  358.560754] CPU: 0 PID: 30 Comm: kworker/0:1 Not tainted 5.0.0-custom-13382-gf2449babf221 #1350
[  358.570472] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016
[  358.580582] Workqueue: events switchdev_deferred_process_work
[  358.587001] RIP: 0010:switchdev_port_obj_add_now+0x9b/0xe0
...
[  358.614109] RSP: 0018:ffffa6b900d6fe18 EFLAGS: 00010286
[  358.619943] RAX: 0000000000000000 RBX: ffff8b00797ff000 RCX: 0000000000000000
[  358.627912] RDX: ffff8b00b7a1d4c0 RSI: ffff8b00b7a152e8 RDI: ffff8b00b7a152e8
[  358.635881] RBP: ffff8b005c3f5bc0 R08: 000000000000022b R09: 0000000000000000
[  358.643850] R10: 0000000000000000 R11: ffffa6b900d6fcc8 R12: 0000000000000000
[  358.651819] R13: dead000000000100 R14: ffff8b00b65a23c0 R15: 0ffff8b00b7a2200
[  358.659790] FS:  0000000000000000(0000) GS:ffff8b00b7a00000(0000) knlGS:0000000000000000
[  358.668820] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  358.675228] CR2: 00007f00aad90de0 CR3: 00000001ca80d000 CR4: 00000000001006f0
[  358.683188] Call Trace:
[  358.685918]  switchdev_port_obj_add_deferred+0x13/0x60
[  358.691655]  switchdev_deferred_process+0x6b/0xf0
[  358.696907]  switchdev_deferred_process_work+0xa/0x10
[  358.702548]  process_one_work+0x1f5/0x3f0
[  358.707022]  worker_thread+0x28/0x3c0
[  358.711099]  ? process_one_work+0x3f0/0x3f0
[  358.715768]  kthread+0x10d/0x130
[  358.719369]  ? __kthread_create_on_node+0x180/0x180
[  358.724815]  ret_from_fork+0x35/0x40

Fixes: 3a49b4fd ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NAlex Kushnarov <alexanderk@mellanox.com>
Tested-by: NAlex Kushnarov <alexanderk@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2019-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Various fixes:
 * iTXQ fixes from Felix
 * tracing fix - increase message length
 * fix SW_CRYPTO_CONTROL enforcement
 * WMM rule handling for regdomain intersection
 * max_interfaces in hwsim - reported by syzbot
 * clear private data in some more commands
 * a clang compiler warning fix

I added a patch with two new (unused) macros for
rate-limited printing to simplify getting the users
into the tree.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restore SW_CRYPTO_CONTROL operation on AP_VLAN interfaces for unicast
keys, the original override was intended to be done for group keys as
those are treated specially by mac80211 and would always have been
rejected.

Now the situation is that AP_VLAN support must be enabled by the driver
if it can support it (meaning it can support software crypto GTK TX).

Thus, also simplify the code - if we get here with AP_VLAN and non-
pairwise key, software crypto must be used (driver doesn't know about
the interface) and can be used (driver must've advertised AP_VLAN if
it also uses SW_CRYPTO_CONTROL).

Fixes: db3bdcb9 ("mac80211: allow AP_VLAN operation on crypto controlled devices")
Signed-off-by: NAlexander Wetzel <alexander@wetzel-home.de>
[rewrite commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Pull networking fixes from David Miller:

 1) Off by one and bounds checking fixes in NFC, from Dan Carpenter.

 2) There have been many weird regressions in r8169 since we turned ASPM
    support on, some are still not understood nor completely resolved.
    Let's turn this back off for now. From Heiner Kallweit.

 3) Signess fixes for ethtool speed value handling, from Michael
    Zhivich.

 4) Handle timestamps properly in macb driver, from Paul Thomas.

 5) Two erspan fixes, it's the usual "skb ->data potentially reallocated
    and we're holding a stale protocol header pointer". From Lorenzo
    Bianconi.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  bnxt_en: Reset device on RX buffer errors.
  bnxt_en: Improve RX consumer index validity check.
  net: macb driver, check for SKBTX_HW_TSTAMP
  qlogic: qlcnic: fix use of SPEED_UNKNOWN ethtool constant
  broadcom: tg3: fix use of SPEED_UNKNOWN ethtool constant
  ethtool: avoid signed-unsigned comparison in ethtool_validate_speed()
  net: ip6_gre: fix possible use-after-free in ip6erspan_rcv
  net: ip_gre: fix possible use-after-free in erspan_rcv
  r8169: disable ASPM again
  MAINTAINERS: ieee802154: update documentation file pattern
  net: vrf: Fix ping failed when vrf mtu is set to 0
  selftests: add a tc matchall test case
  nfc: nci: Potential off by one in ->pipes[] array
  NFC: nci: Add some bounds checking in nci_hci_cmd_received()

Pull TPM fixes from James Morris:
 "From Jarkko: These are critical fixes for v5.1. Contains also couple
  of new selftests for v5.1 features (partial reads in /dev/tpm0)"

* 'fixes-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  selftests/tpm2: Open tpm dev in unbuffered mode
  selftests/tpm2: Extend tests to cover partial reads
  KEYS: trusted: fix -Wvarags warning
  tpm: Fix the type of the return value in calc_tpm2_event_size()
  KEYS: trusted: allow trusted.ko to initialize w/o a TPM
  tpm: fix an invalid condition in tpm_common_poll
  tpm: turn on TPM on suspend for TPM 1.x

Pull xtensa fixes from Max Filippov:

 - fix syscall number passed to trace_sys_exit

 - fix syscall number initialization in start_thread

 - fix level interpretation in the return_address

 - fix format string warning in init_pmd

* tag 'xtensa-20190408' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: fix format string warning in init_pmd
  xtensa: fix return_address
  xtensa: fix initialization of pt_regs::syscall in start_thread
  xtensa: use actual syscall number in do_syscall_trace_leave

Michael Chan says:

====================
bnxt_en: 2 bug fixes.

The first patch prevents possible driver crash if we get a bad RX index
from the hardware.  The second patch resets the device when the hardware
reports buffer error to recover from the error.

Please queue these for -stable also.  Thanks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the RX completion indicates RX buffers errors, the RX ring will be
disabled by firmware and no packets will be received on that ring from
that point on.  Recover by resetting the device.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is logic to check that the RX/TPA consumer index is the expected
index to work around a hardware problem.  However, the potentially bad
consumer index is first used to index into an array to reference an entry.
This can potentially crash if the bad consumer index is beyond legal
range.  Improve the logic to use the consumer index for dereferencing
after the validity check and log an error message.

Fixes: fa7e2812 ("bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure SKBTX_HW_TSTAMP (i.e. SOF_TIMESTAMPING_TX_HARDWARE) has been
enabled for this skb. It does fix the issue where normal socks that
aren't expecting a timestamp will not wake up on select, but when a
user does want a SOF_TIMESTAMPING_TX_HARDWARE it does work.
Signed-off-by: NPaul Thomas <pthomas8589@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michael Zhivich says:

====================
ethtool: fix use of SPEED_UNKNOWN constant

This patch series addresses 2 related issues:

1. ethtool_validate_speed() triggers a "signed-unsigned comparison"
warning due to type difference of SPEED_UNKNOWN constant (int)
and argument to ethtool_validate_speed (__u32).

2. some drivers use u16 storage for SPEED_UNKNOWN constant,
resulting in value truncation and thus failure to test against
SPEED_UNKNOWN correctly.

This revised series addresses several feedback comments:
- split up the patch in to series
- do not unnecessarily change drivers that use "int" storage
  for speed values
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qlcnic driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.

For example, the following test will print "False":

    u16 speed = SPEED_UNKNOWN;

    if (speed == SPEED_UNKNOWN)
        printf("True");
    else
        printf("False");

Change storage of speed to use u32 to avoid this issue.
Signed-off-by: NMichael Zhivich <mzhivich@akamai.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tg3 driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.

For example, the following test will print "False":

	u16 speed = SPEED_UNKNOWN;

	if (speed == SPEED_UNKNOWN)
	    printf("True");
	else
	    printf("False");

Change storage of speed to use u32 to avoid this issue.
Signed-off-by: NMichael Zhivich <mzhivich@akamai.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When building C++ userspace code that includes ethtool.h
with "-Werror -Wall", g++ complains about signed-unsigned comparison in
ethtool_validate_speed() due to definition of SPEED_UNKNOWN as -1.

Explicitly cast SPEED_UNKNOWN to __u32 to match type of
ethtool_validate_speed() argument.
Signed-off-by: NMichael Zhivich <mzhivich@akamai.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lorenzo Bianconi says:

====================
fix possible use-after-free in erspan_v{4,6}

Similar to what I did in commit bb9bd814 ("ipv6: sit: reset ip
header pointer in ipip6_rcv"), fix possible use-after-free in
erspan_rcv and ip6erspan_rcv extracting tunnel metadata since the
packet can be 'uncloned' running __iptunnel_pull_header
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

erspan_v6 tunnels run __iptunnel_pull_header on received skbs to remove
erspan header. This can determine a possible use-after-free accessing
pkt_md pointer in ip6erspan_rcv since the packet will be 'uncloned'
running pskb_expand_head if it is a cloned gso skb (e.g if the packet has
been sent though a veth device). Fix it resetting pkt_md pointer after
__iptunnel_pull_header

Fixes: 1d7e2ed2 ("net: erspan: refactor existing erspan code")
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

erspan tunnels run __iptunnel_pull_header on received skbs to remove
gre and erspan headers. This can determine a possible use-after-free
accessing pkt_md pointer in erspan_rcv since the packet will be 'uncloned'
running pskb_expand_head if it is a cloned gso skb (e.g if the packet has
been sent though a veth device). Fix it resetting pkt_md pointer after
__iptunnel_pull_header

Fixes: 1d7e2ed2 ("net: erspan: refactor existing erspan code")
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to have control over how many bytes are read or written
the device needs to be opened in unbuffered mode.
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJames Morris <james.morris@microsoft.com>

Three new tests added:
1. Send get random cmd, read header in 1st read, read the rest in second
   read - expect success
2. Send get random cmd, read only part of the response, send another
   get random command, read the response - expect success
3. Send get random cmd followed by another get random cmd, without
   reading the first response - expect the second cmd to fail with -EBUSY
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJames Morris <james.morris@microsoft.com>

Fixes the warning reported by Clang:
security/keys/trusted.c:146:17: warning: passing an object that
undergoes default
      argument promotion to 'va_start' has undefined behavior [-Wvarargs]
        va_start(argp, h3);
                       ^
security/keys/trusted.c:126:37: note: parameter of type 'unsigned
char' is declared here
unsigned char *h2, unsigned char h3, ...)
                               ^
Specifically, it seems that both the C90 (4.8.1.1) and C11 (7.16.1.4)
standards explicitly call this out as undefined behavior:

The parameter parmN is the identifier of the rightmost parameter in
the variable parameter list in the function definition (the one just
before the ...). If the parameter parmN is declared with ... or with a
type that is not compatible with the type that results after
application of the default argument promotions, the behavior is
undefined.

Link: https://github.com/ClangBuiltLinux/linux/issues/41
Link: https://www.eskimo.com/~scs/cclass/int/sx11c.htmlSuggested-by: NDavid Laight <David.Laight@aculab.com>
Suggested-by: NDenis Kenzior <denkenz@gmail.com>
Suggested-by: NJames Bottomley <jejb@linux.vnet.ibm.com>
Suggested-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NNick Desaulniers <ndesaulniers@google.com>
Reviewed-by: NNathan Chancellor <natechancellor@gmail.com>
Tested-by: NNathan Chancellor <natechancellor@gmail.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJames Morris <james.morris@microsoft.com>

calc_tpm2_event_size() has an invalid signature because
it returns a 'size_t' where as its signature says that
it returns 'int'.

Cc: <stable@vger.kernel.org>
Fixes: 4d23cc32 ("tpm: add securityfs support for TPM 2.0 firmware event log")
Suggested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NYue Haibing <yuehaibing@huawei.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJames Morris <james.morris@microsoft.com>

Allow trusted.ko to initialize w/o a TPM. This commit also adds checks
to the exported functions to fail when a TPM is not available.

Fixes: 24073043 ("KEYS: trusted: explicitly use tpm_chip structure...")
Cc: James Morris <jmorris@namei.org>
Reported-by: NDan Williams <dan.j.williams@intel.com>
Tested-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJames Morris <james.morris@microsoft.com>

The poll condition should only check response_length,
because reads should only be issued if there is data to read.
The response_read flag only prevents double writes.
The problem was that the write set the response_read to false,
enqued a tpm job, and returned. Then application called poll
which checked the response_read flag and returned EPOLLIN.
Then the application called read, but got nothing.
After all that the async_work kicked in.
Added also mutex_lock around the poll check to prevent
other possible race conditions.

Fixes: 9488585b ("tpm: add support for partial reads")
Reported-by: NMantas Mikulėnas <grawity@gmail.com>
Tested-by: NMantas Mikulėnas <grawity@gmail.com>
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJames Morris <james.morris@microsoft.com>

tpm_chip_start/stop() should be also called for TPM 1.x devices on
suspend. Add that functionality back. Do not lock the chip because
it is unnecessary as there are no multiple threads using it when
doing the suspend.

Fixes: a3fbfae8 ("tpm: take TPM chip power gating out of tpm_transmit()")
Reported-by: NPaul Zimmerman <pauldzim@gmail.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NDomenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: NJames Morris <james.morris@microsoft.com>

There's a significant number of reports that re-enabling ASPM causes
different issues, ranging from decreased performance to system not
booting at all. This affects only a minority of users, but the number
of affected users is big enough that we better switch off ASPM again.

This will hurt notebook users who are not affected by the issues, they
may see decreased battery runtime w/o ASPM. With the PCI core folks is
being discussed to add generic sysfs attributes to control ASPM.
Once this is in place brave enough users can re-enable ASPM on their
system.

Fixes: a99790bf ("r8169: Reinstate ASPM Support")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When moving the documentation for the ieee802154 subsystem from
plain text to rst the file pattern in the MAINTAINERS file got wrong.
Updating it here to fix scripts using this file.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.

This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.

Also add an extra argument to ieee80211_return_txq to get the same behavior.

This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.

Fixes: 89cea749 ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Acked-by: NToke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If we just set this to 2048, and have multiple limits you
can select from, the total number might run over and cause
a warning in cfg80211. This doesn't make sense, so we just
calculate the total max_interfaces now.

Reported-by: syzbot+8f91bd563bbff230d0ee@syzkaller.appspotmail.com
Fixes: 99e3a44b ("mac80211_hwsim: allow setting iftype support")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

wiphy_{err,warn}_ratelimited will be used by rt2x00
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Pull crypto fix from Herbert Xu:
 "This fixes a bug in the implementation of xcbc and cmac in caam"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: caam - fix copy of next buffer for xcbc and cmac

When the mtu of a vrf device is set to 0, it would cause ping
failed. So I think we should limit vrf mtu in a reasonable range
to solve this problem. I set dev->min_mtu to IPV6_MIN_MTU, so it
will works for both ipv4 and ipv6. And if dev->max_mtu still be 0
can be confusing, so I set dev->max_mtu to ETH_MAX_MTU.

Here is the reproduce step:

1.Config vrf interface and set mtu to 0:
3: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel
master vrf1 state UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:9e:dd:c1 brd ff:ff:ff:ff:ff:ff

2.Ping peer:
3: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel
master vrf1 state UP group default qlen 1000
    link/ether 52:54:00:9e:dd:c1 brd ff:ff:ff:ff:ff:ff
    inet 10.0.0.1/16 scope global enp4s0
       valid_lft forever preferred_lft forever
connect: Network is unreachable

3.Set mtu to default value, ping works:
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
64 bytes from 10.0.0.2: icmp_seq=1 ttl=64 time=1.88 ms

Fixes: ad49bc63 ("net: vrf: remove MTU limits for vrf device")
Signed-off-by: NMiaohe Lin <linmiaohe@huawei.com>
Reviewed-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 510ded33 ("slab: implement slab_root_caches list")
changes the name of the list node within "struct kmem_cache" from "list"
to "root_caches_node", but leaks_show() still use the "list" which
causes a crash when reading /proc/slab_allocators.

You need to have CONFIG_SLAB=y and CONFIG_MEMCG=y to see the problem,
because without MEMCG all slab caches are root caches, and the "list"
node happens to be the right one.

Fixes: 510ded33 ("slab: implement slab_root_caches list")
Signed-off-by: NQian Cai <cai@lca.pw>
Reviewed-by: NTobin C. Harding <tobin@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>