Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 27 2月, 2022 4 次提交
    • V
      net: dsa: tag_8021q: rename dsa_8021q_bridge_tx_fwd_offload_vid · b6362bdf
      由 Vladimir Oltean 提交于 
      The dsa_8021q_bridge_tx_fwd_offload_vid is no longer used just for
bridge TX forwarding offload, it is the private VLAN reserved for
VLAN-unaware bridging in a way that is compatible with FDB isolation.

So just rename it dsa_tag_8021q_bridge_vid.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b6362bdf
    • V
      net: dsa: tag_8021q: merge RX and TX VLANs · 04b67e18
      由 Vladimir Oltean 提交于 
      In the old Shared VLAN Learning mode of operation that tag_8021q
previously used for forwarding, we needed to have distinct concepts for
an RX and a TX VLAN.

An RX VLAN could be installed on all ports that were members of a given
bridge, so that autonomous forwarding could still work, while a TX VLAN
was dedicated for precise packet steering, so it just contained the CPU
port and one egress port.

Now that tag_8021q uses Independent VLAN Learning and imprecise RX/TX
all over, those lines have been blurred and we no longer have the need
to do precise TX towards a port that is in a bridge. As for standalone
ports, it is fine to use the same VLAN ID for both RX and TX.

This patch changes the tag_8021q format by shifting the VLAN range it
reserves, and halving it. Previously, our DIR bits were encoding the
VLAN direction (RX/TX) and were set to either 1 or 2. This meant that
tag_8021q reserved 2K VLANs, or 50% of the available range.

Change the DIR bits to a hardcoded value of 3 now, which makes tag_8021q
reserve only 1K VLANs, and a different range now (the last 1K). This is
done so that we leave the old format in place in case we need to return
to it.

In terms of code, the vid_is_dsa_8021q_rxvlan and vid_is_dsa_8021q_txvlan
functions go away. Any vid_is_dsa_8021q is both a TX and an RX VLAN, and
they are no longer distinct. For example, felix which did different
things for different VLAN types, now needs to handle the RX and the TX
logic for the same VLAN.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      04b67e18
    • V
      net: dsa: felix: delete workarounds present due to SVL tag_8021q bridging · 08f44db3
      由 Vladimir Oltean 提交于 
      The felix driver, which also has a tagging protocol implementation based
on tag_8021q, does not care about adding the RX VLAN that is pvid on one
port on the other ports that are in the same bridge with it. It simply
doesn't need that, because in its implementation, the RX VLAN that is
pvid of a port is only used to install a TCAM rule that pushes that VLAN
ID towards the CPU port.

Now that tag_8021q no longer performs Shared VLAN Learning based
forwarding, the RX VLANs are actually segregated into two types:
standalone VLANs and VLAN-unaware bridging VLANs. Since you actually
have to call dsa_tag_8021q_bridge_join() to get a bridging VLAN from
tag_8021q, and felix does not do that because it doesn't need it, it
means that it only gets standalone port VLANs from tag_8021q. Which is
perfect because this means it can drop its workarounds that avoid the
VLANs it does not need.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      08f44db3
    • V
      net: dsa: tag_8021q: replace the SVL bridging with VLAN-unaware IVL bridging · 91495f21
      由 Vladimir Oltean 提交于 
      For VLAN-unaware bridging, tag_8021q uses something perhaps a bit too
tied with the sja1105 switch: each port uses the same pvid which is also
used for standalone operation (a unique one from which the source port
and device ID can be retrieved when packets from that port are forwarded
to the CPU). Since each port has a unique pvid when performing
autonomous forwarding, the switch must be configured for Shared VLAN
Learning (SVL) such that the VLAN ID itself is ignored when performing
FDB lookups. Without SVL, packets would always be flooded, since FDB
lookup in the source port's VLAN would never find any entry.

First of all, to make tag_8021q more palatable to switches which might
not support Shared VLAN Learning, let's just use a common VLAN for all
ports that are under the same bridge.

Secondly, using Shared VLAN Learning means that FDB isolation can never
be enforced. But if all ports under the same VLAN-unaware bridge share
the same VLAN ID, it can.

The disadvantage is that the CPU port can no longer perform precise
source port identification for these packets. But at least we have a
mechanism which has proven to be adequate for that situation: imprecise
RX (dsa_find_designated_bridge_port_by_vid), which is what we use for
termination on VLAN-aware bridges.

The VLAN ID that VLAN-unaware bridges will use with tag_8021q is the
same one as we were previously using for imprecise TX (bridge TX
forwarding offload). It is already allocated, it is just a matter of
using it.

Note that because now all ports under the same bridge share the same
VLAN, the complexity of performing a tag_8021q bridge join decreases
dramatically. We no longer have to install the RX VLAN of a newly
joining port into the port membership of the existing bridge ports.
The newly joining port just becomes a member of the VLAN corresponding
to that bridge, and the other ports are already members of it from when
they joined the bridge themselves. So forwarding works properly.

This means that we can unhook dsa_tag_8021q_bridge_{join,leave} from the
cross-chip notifier level dsa_switch_bridge_{join,leave}. We can put
these calls directly into the sja1105 driver.

With this new mode of operation, a port controlled by tag_8021q can have
two pvids whereas before it could only have one. The pvid for standalone
operation is different from the pvid used for VLAN-unaware bridging.
This is done, again, so that FDB isolation can be enforced.
Let tag_8021q manage this by deleting the standalone pvid when a port
joins a bridge, and restoring it when it leaves it.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      91495f21
  3. 26 2月, 2022 5 次提交
  5. 25 2月, 2022 12 次提交
  7. 23 2月, 2022 4 次提交
    • H
      net: dsa: mv88e6xxx: Add support for bridge port locked mode · 34ea415f
      由 Hans Schultz 提交于 
      Supporting bridge ports in locked mode using the drop on lock
feature in Marvell mv88e6xxx switchcores is described in the
'88E6096/88E6097/88E6097F Datasheet', sections 4.4.6, 4.4.7 and
5.1.2.1 (Drop on Lock).

This feature is implemented here facilitated by the locked port flag.
Signed-off-by: NHans Schultz <schultz.hans+netdev@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      34ea415f
    • A
      net: dsa: realtek: rtl8365mb: serialize indirect PHY register access · 27967284
      由 Alvin Šipraga 提交于 
      Realtek switches in the rtl8365mb family can access the PHY registers of
the internal PHYs via the switch registers. This method is called
indirect access. At a high level, the indirect PHY register access
method involves reading and writing some special switch registers in a
particular sequence. This works for both SMI and MDIO connected
switches.

Currently the rtl8365mb driver does not take any care to serialize the
aforementioned access to the switch registers. In particular, it is
permitted for other driver code to access other switch registers while
the indirect PHY register access is ongoing. Locking is only done at the
regmap level. This, however, is a bug: concurrent register access, even
to unrelated switch registers, risks corrupting the PHY register value
read back via the indirect access method described above.

Arınç reported that the switch sometimes returns nonsense data when
reading the PHY registers. In particular, a value of 0 causes the
kernel's PHY subsystem to think that the link is down, but since most
reads return correct data, the link then flip-flops between up and down
over a period of time.

The aforementioned bug can be readily observed by:

 1. Enabling ftrace events for regmap and mdio
 2. Polling BSMR PHY register for a connected port;
    it should always read the same (e.g. 0x79ed)
 3. Wait for step 2 to give a different value

Example command for step 2:

    while true; do phytool read swp2/2/0x01; done

On my i.MX8MM, the above steps will yield a bogus value for the BSMR PHY
register within a matter of seconds. The interleaved register access it
then evident in the trace log:

 kworker/3:4-70      [003] .......  1927.139849: regmap_reg_write: ethernet-switch reg=1004 val=bd
     phytool-16816   [002] .......  1927.139979: regmap_reg_read: ethernet-switch reg=1f01 val=0
 kworker/3:4-70      [003] .......  1927.140381: regmap_reg_read: ethernet-switch reg=1005 val=0
     phytool-16816   [002] .......  1927.140468: regmap_reg_read: ethernet-switch reg=1d15 val=a69
 kworker/3:4-70      [003] .......  1927.140864: regmap_reg_read: ethernet-switch reg=1003 val=0
     phytool-16816   [002] .......  1927.140955: regmap_reg_write: ethernet-switch reg=1f02 val=2041
 kworker/3:4-70      [003] .......  1927.141390: regmap_reg_read: ethernet-switch reg=1002 val=0
     phytool-16816   [002] .......  1927.141479: regmap_reg_write: ethernet-switch reg=1f00 val=1
 kworker/3:4-70      [003] .......  1927.142311: regmap_reg_write: ethernet-switch reg=1004 val=be
     phytool-16816   [002] .......  1927.142410: regmap_reg_read: ethernet-switch reg=1f01 val=0
 kworker/3:4-70      [003] .......  1927.142534: regmap_reg_read: ethernet-switch reg=1005 val=0
     phytool-16816   [002] .......  1927.142618: regmap_reg_read: ethernet-switch reg=1f04 val=0
     phytool-16816   [002] .......  1927.142641: mdio_access: SMI-0 read  phy:0x02 reg:0x01 val:0x0000 <- ?!
 kworker/3:4-70      [003] .......  1927.143037: regmap_reg_read: ethernet-switch reg=1001 val=0
 kworker/3:4-70      [003] .......  1927.143133: regmap_reg_read: ethernet-switch reg=1000 val=2d89
 kworker/3:4-70      [003] .......  1927.143213: regmap_reg_write: ethernet-switch reg=1004 val=be
 kworker/3:4-70      [003] .......  1927.143291: regmap_reg_read: ethernet-switch reg=1005 val=0
 kworker/3:4-70      [003] .......  1927.143368: regmap_reg_read: ethernet-switch reg=1003 val=0
 kworker/3:4-70      [003] .......  1927.143443: regmap_reg_read: ethernet-switch reg=1002 val=6

The kworker here is polling MIB counters for stats, as evidenced by the
register 0x1004 that we are writing to (RTL8365MB_MIB_ADDRESS_REG). This
polling is performed every 3 seconds, but is just one example of such
unsynchronized access. In Arınç's case, the driver was not using the
switch IRQ, so the PHY subsystem was itself doing polling analogous to
phytool in the above example.

A test module was created [see second Link] to simulate such spurious
switch register accesses while performing indirect PHY register reads
and writes. Realtek was also consulted to confirm whether this is a
known issue or not. The conclusion of these lines of inquiry is as
follows:

1. Reading of PHY registers via indirect access will be aborted if,
   after executing the read operation (via a write to the
   INDIRECT_ACCESS_CTRL_REG), any register is accessed, other than
   INDIRECT_ACCESS_STATUS_REG.

2. The PHY register indirect read is only complete when
   INDIRECT_ACCESS_STATUS_REG reads zero.

3. The INDIRECT_ACCESS_DATA_REG, which is read to get the result of the
   PHY read, will contain the result of the last successful read
   operation. If there was spurious register access and the indirect
   read was aborted, then this register is not guaranteed to hold
   anything meaningful and the PHY read will silently fail.

4. PHY writes do not appear to be affected by this mechanism.

5. Other similar access routines, such as for MIB counters, although
   similar to the PHY indirect access method, are actually table access.
   Table access is not affected by spurious reads or writes of other
   registers. However, concurrent table access is not allowed. Currently
   this is protected via mib_lock, so there is nothing to fix.

The above statements are corroborated both via the test module and
through consultation with Realtek. In particular, Realtek states that
this is simply a property of the hardware design and is not a hardware
bug.

To fix this problem, one must guard against regmap access while the
PHY indirect register read is executing. Fix this by using the newly
introduced "nolock" regmap in all PHY-related functions, and by aquiring
the regmap mutex at the top level of the PHY register access callbacks.
Although no issue has been observed with PHY register _writes_, this
change also serializes the indirect access method there. This is done
purely as a matter of convenience and for reasons of symmetry.

Fixes: 4af2950c ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Link: https://lore.kernel.org/netdev/CAJq09z5FCgG-+jVT7uxh1a-0CiiFsoKoHYsAWJtiKwv7LXKofQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/871qzwjmtv.fsf@bang-olufsen.dk/Reported-by: NArınç ÜNAL <arinc.unal@arinc9.com>
Reported-by: NLuiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: NAlvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      27967284
    • A
      net: dsa: realtek: allow subdrivers to externally lock regmap · 907e772f
      由 Alvin Šipraga 提交于 
      Currently there is no way for Realtek DSA subdrivers to serialize
consecutive regmap accesses. In preparation for a bugfix relating to
indirect PHY register access - which involves a series of regmap
reads and writes - add a facility for subdrivers to serialize their
regmap access.

Specifically, a mutex is added to the driver private data structure and
the standard regmap is initialized with custom lock/unlock ops which use
this mutex. Then, a "nolock" variant of the regmap is added, which is
functionally equivalent to the existing regmap except that regmap
locking is disabled. Functions that wish to serialize a sequence of
regmap accesses may then lock the newly introduced driver-owned mutex
before using the nolock regmap.

Doing things this way means that subdriver code that doesn't care about
serialized register access - i.e. the vast majority of code - needn't
worry about synchronizing register access with an external lock: it can
just continue to use the original regmap.

Another advantage of this design is that, while regmaps with locking
disabled do not expose a debugfs interface for obvious reasons, there
still exists the original regmap which does expose this interface. This
interface remains safe to use even combined with driver codepaths that
use the nolock regmap, because said codepaths will use the same mutex
to synchronize access.

With respect to disadvantages, it can be argued that having
near-duplicate regmaps is confusing. However, the naming is rather
explicit, and examples will abound.

Finally, while we are at it, rename realtek_smi_mdio_regmap_config to
realtek_smi_regmap_config. This makes it consistent with the naming
realtek_mdio_regmap_config in realtek-mdio.c.
Signed-off-by: NAlvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      907e772f
    • O
      net: dsa: microchip: ksz9477: reduce polling interval for statistics · 12c740c8
      由 Oleksij Rempel 提交于 
      30 seconds is too long interval especially if it used with ip -s l.
Reduce polling interval to 5 sec.
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220221084129.3660124-1-o.rempel@pengutronix.deSigned-off-by: NJakub Kicinski <kuba@kernel.org>
      12c740c8
  9. 22 2月, 2022 5 次提交
  11. 20 2月, 2022 3 次提交
  13. 18 2月, 2022 6 次提交
  15. 17 2月, 2022 1 次提交
    • V
      net: dsa: felix: update destinations of existing traps with ocelot-8021q · 99348004
      由 Vladimir Oltean 提交于 
      Historically, the felix DSA driver has installed special traps such that
PTP over L2 works with the ocelot-8021q tagging protocol; commit
0a6f17c6 ("net: dsa: tag_ocelot_8021q: add support for PTP
timestamping") has the details.

Then the ocelot switch library also gained more comprehensive support
for PTP traps through commit 96ca08c0 ("net: mscc: ocelot: set up
traps for PTP packets").

Right now, PTP over L2 works using ocelot-8021q via the traps it has set
for itself, but nothing else does. Consolidating the two code blocks
would make ocelot-8021q gain support for PTP over L4 and tc-flower
traps, and at the same time avoid some code and TCAM duplication.

The traps are similar in intent, but different in execution, so some
explanation is required. The traps set up by felix_setup_mmio_filtering()
are VCAP IS1 filters, which have a PAG that chains them to a VCAP IS2
filter, and the IS2 is where the 'trap' action resides. The traps set up
by ocelot_trap_add(), on the other hand, have a single filter, in VCAP
IS2. The reason for chaining VCAP IS1 and IS2 in Felix was to ensure
that the hardcoded traps take precedence and cannot be overridden by the
Ocelot switch library.

So in principle, the PTP traps needed for ocelot-8021q in the Felix
driver can rely on ocelot_trap_add(), but the filters need to be patched
to account for a quirk that LS1028A has: the quirk_no_xtr_irq described
in commit 0a6f17c6 ("net: dsa: tag_ocelot_8021q: add support for PTP
timestamping"). Live-patching is done by iterating through the trap list
every time we know it has been updated, and transforming a trap into a
redirect + CPU copy if ocelot-8021q is in use.

Making the DSA ocelot-8021q tagger work with the Ocelot traps means we
can eliminate the dedicated OCELOT_VCAP_IS1_TAG_8021Q_PTP_MMIO and
OCELOT_VCAP_IS2_TAG_8021Q_PTP_MMIO cookies. To minimize the patch delta,
OCELOT_VCAP_IS2_MRP_TRAP takes the place of OCELOT_VCAP_IS2_TAG_8021Q_PTP_MMIO
(the alternative would have been to left-shift all cookie numbers by 1).
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      99348004