It doesn't hurt and on my notebook despite clearing the
wake flag the remote still wakes up the system.

This way it doesn't.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

While we can delay IRQ intialization, we need the interrupt number
right away because unusually hardware have programable interrupt number,
and thus we give it the number that was allocated by BIOS
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

We have reorganized the error handling into a simpler and more canonical
format.
Additionally we removed extra empty lines, switched to devm_kzalloc(), and
substitute 'minor' by 'ret' in the igorplugusb_remote_probe() function.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Set fmt.pix.priv to zero in vidioc_try_fmt_vid_cap.
Catched by v4l2-compliance.
Signed-off-by: NAlban Browaeys <prahal@yahoo.com>
[hans.verkuil@cisco.com: dropping unnecessary change to g_fmt_vid_cap]
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Current stereo detection code is wrong - it reads TUNED bit instead of STEREO bit.
Fix that and implement signal strength detection too.
Also remove useless s_stereo functionn.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Aztech radio card is based on LM7001 chip which is (software) compatible with LM7000.
So remove the LM7000-specific code from the driver and use generic code.
Also found that the card does not have A0..A2 ISA pins connected, which means that the region size is 8 bytes.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Kodicom 4400R and Geovision GV-800 code in bttv driver abuses mbox_we (int)
in struct bttv as char *.
Remove this hack and add a proper sw_status array to struct bttv instead.
This is a a preparation to remove mbox_we.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Move HW initialization to separate function to allow using the code without
the v4l parts. This is needed for use in the bttv driver.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This commit adds an early check to vidioc_s_std() to detect if the
new and current standards are equal, and exit with success in that
case.
This is needed to prevent userspace applications that might attempt
to re-set the same standard from failing if that's done when streaming
has started.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Remove the check as there's no reason to prevent the input from
being set when the device is streaming. This allows surveillance
applications (such as motion, zoneminder, etc.) to configure the
input while streaming.
Reported-by: NSergey 'Jin' Bostandzhyan <jin@mediatomb.cc>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Remove including <linux/version.h> that don't need it.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NLubomir Rintel <lkundrak@v3.sk>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

ML86V7667 always transmits top field first for both PAL and  NTSC -- that makes
application incorrectly  treat interlaced  fields when relying on the standard.
Hence we must set V4L2_FIELD_INTERLACED_TB format explicitly.

[Sergei: added a comment.]
Reported-by: NKatsuya MATSUBARA <matsu@igel.co.jp>
Signed-off-by: NVladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: NKatsuya MATSUBARA <matsu@igel.co.jp>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Alongside already existing Composite input.
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

check_firmware() makes sure firmware is in a device.
It returns zero on success and error code otherwise.
Also it sets down_firmware flag to 1 if downloading occurs.
The only caller poseidon_probe() checks down_firmware flag and
returns 0 without any initialization if it is set.
That looks very strange, so the patch removes down_firmware argument
of check_firmware() and returns error code if check_firmware() fails
in poseidon_probe().
Not tested on real hardware.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

All poseidon init functions properly return error codes,
but they are ignored by poseidon_probe(). The patch implements
handling of error cases.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

use module_pci_driver instead of init/exit, make code clean
Signed-off-by: NLibo Chen <libo.chen@huawei.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch switchs to resource managed allocation and request in mmp-driver.
It can remove free resource operations.
Signed-off-by: NAlbert Wang <twang13@marvell.com>
Signed-off-by: NLibin Yang <lbyang@marvell.com>
Acked-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch adds the SOFx/EOFx pair check for marvell-ccic.
When switching format, the last EOF may not arrive when stop streamning.
And the EOF will be detected in the next start streaming.
Must ensure clear the left over frame flags before every really start streaming.
Signed-off-by: NAlbert Wang <twang13@marvell.com>
Signed-off-by: NLibin Yang <lbyang@marvell.com>
Acked-by: NJonathan Corbet <corbet@lwn.net>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch adds some planar formats support for marvell-ccic.
Signed-off-by: NAlbert Wang <twang13@marvell.com>
Signed-off-by: NLibin Yang <lbyang@marvell.com>
Acked-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch refines mcam_set_contig_buffer() in mcam core.
It can remove redundant code line and enhance readability.
Signed-off-by: NAlbert Wang <twang13@marvell.com>
Signed-off-by: NLibin Yang <lbyang@marvell.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch adds the reset ccic phy operation when stop streaming.
Stop streaming without reset ccic phy, the next start streaming
may be unstable.
Also need add CCIC2 definition when PXA688/PXA2128 support dual ccics.
Signed-off-by: NAlbert Wang <twang13@marvell.com>
Signed-off-by: NLibin Yang <lbyang@marvell.com>
Acked-by: NJonathan Corbet <corbet@lwn.net>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch adds the clock tree support for marvell-ccic.
Signed-off-by: NLibin Yang <lbyang@marvell.com>
Signed-off-by: NAlbert Wang <twang13@marvell.com>
Acked-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch adds the MIPI support for marvell-ccic.
Board driver should determine whether using MIPI or not.
Signed-off-by: NAlbert Wang <twang13@marvell.com>
Signed-off-by: NLibin Yang <lbyang@marvell.com>
Acked-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

add OF support for the adv7343 driver.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch makes the platform data members as array wherever
possible, so as this makes easier while collecting the data
in DT case and read the entire array at once.
This patch also makes appropriate changes to board-da850-evm.c
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for asynchronous subdevice probing, using the v4l2-async API.
The legacy synchronous mode is still supported too, which allows to
gradually update drivers and platforms.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for asynchronous subdevice probing, using the v4l2-async API.
The legacy synchronous mode is still supported too, which allows to
gradually update drivers and platforms.
Signed-off-by: NPrabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Both synchronous and asynchronous tvp514x subdevice probing
is supported by this patch.
This patch also fixes the error path by calling
media_entity_cleanup() on failure in probe when
CONFIG_MEDIA_CONTROLLER is enabled.
Signed-off-by: NPrabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Both synchronous and asynchronous tvp7002 subdevice probing
is supported by this patch.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Both synchronous and asynchronous adv7343 subdevice probing is supported by
this patch.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

add OF support for the ths8200 driver.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch supports both synchronous and asynchronous
ths8200 subdevice probing.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add a bitstream ringbuffer using kfifo. Queued source buffers are to be copied
into the bitstream ringbuffer immediately and marked as done, if possible.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch splits the global workbuf into a global tempbuf and a per-context
workbuf, adds the codec mode aux register, and restores the work buffer
pointer on commands. With the new firmware, there is only a single set of
read/write pointers which need to be restored between context switches.
This allows more than four active contexts at the same time.
All auxiliary buffers are now allocated through a helper function to avoid
code duplication.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The encoder only ever needs two buffers, but we'll have to increase
CODA_MAX_FRAMEBUFFERS for the decoder.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This sets up IRAM areas used as temporary memory for the different
hardware units depending on the frame size.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>