udbg_init_debug_opal() should be udbg_init_debug_opal_raw() as
the caller in arch/powerpc/kernel/udbg.c expects
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The driver supports a maximum number of ports configurable at compile
time. Make sure the probe() method fails when registering a port that
exceeds the maximum instead of returning success without registering the
port.

This fixes a crash at system suspend time, when the driver tried to
suspend a non-registered port using the UART core.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

When probing fails, the driver must not try to cleanup resources that
have not been initialized. Fix this.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We had a boot regression in Ux500 in the merge window because
two orthogonal pin control schemes for the PL011 were merged
at the same time:

- One using the .init() and .exit() hooks into the platform
  for Ux500 putting the pins into default vs sleep state
  respectively as the port was started/stopped.
  commit a0980660
  "ARM: ux500: switch to using pinctrl for uart0"

- One hogging the default setting at PL011 probe()
  commit 258e0551
  "serial: amba-pl011: adopt pinctrl support"

To get a solution that works for both let's scrap the stuff
in the platform callbacks, instead have the driver itself
select default and sleep states when the port is
started/stopped. Hopefully this works for all clients.
Platform callbacks are bad for device tree migration anyway,
so this rids us of another problem in Ux500.

Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix kconfig symbol test to use "defined":

drivers/tty/serial/serial_txx9.c: warning: "CONFIG_CONSOLE_POLL" is not defined [-Wundef]
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix kernel-doc warnings in drivers/tty/serial/8250/8250.c:

Warning(drivers/tty/serial/8250/8250.c:3128): No description found for parameter 'up'
Warning(drivers/tty/serial/8250/8250.c:3128): Excess function parameter 'port' description in 'serial8250_register_8250_port'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.

The main revert is d29f3ef3 ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:

  fde86d31 - tty: add lockdep annotations
  8f6576ad - tty: fix ldisc lock inversion trace
  d3ca8b64 - pty: Fix lock inversion
  b1d679af - tty: drop the pty lock during hangup
  abcefe5f - tty/amiserial: Add missing argument for tty_unlock()
  fd11b42e - cris: fix missing tty arg in wait_event_interruptible_tty call
  d29f3ef3 - tty_lock: Localise the lock

The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

tty_lock_pair() do the right thing to avoid deadlocks, but should
instruct LOCKDEP of this to avoid a splat.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is caused by tty_release using tty_lock_pair to lock both sides of
the pty/tty pair, and then tty_ldisc_release dropping and relocking one
side only.  We can drop both fine, so drop both to avoid any lock
ordering concerns.

Rework the release path to fix the new locking model.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ptmx_open path takes the tty and devpts locks in the wrong order
because tty_init_dev locks and returns a locked tty.  As far as I can
tell this is actually safe anyway because the tty being returned is new
so nobody can get a reference to lock it at this point.

However we don't even need the devpts lock at this point, it's only held
as a byproduct of the way the locks were pushe down.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We need to make sure that those parameters are setup to be correct.
As such the value of 0 is deemed invalid and we find that we
bail out. The hypervisor sets by default all of them to be zero
and when the hypercall is done does a simple:

 a.value = d->arch.hvm_domain.params[a.index];

Which means that if the Xen toolstack forgot to setup the proper
HVM_PARAM_CONSOLE_EVTCHN (or the PFN one), we would get the
default value of 0 and use that.

CC: stable@kernel.org
Fixes-Oracle-Bug: 14091238
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

We weren't resetting the parameter to be passed in to a
known default. Nor were we checking the return value of
hvm_get_parameter.

CC: stable@kernel.org
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

All of the error paths are doing the same logic. In which
case we might as well collapse them in one path.

CC: stable@kernel.org
Acked-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

If kzalloc() returns a NULL here, we pass a NULL to
xencons_disconnect_backend() which will cause an Oops.

Also I removed the __GFP_ZERO while I was at it since kzalloc() implies
__GFP_ZERO.

CC: stable@kernel.org
Acked-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Add devicetree and handling for our new clkdev clocks. The patch is rather
straightforward. .of_match_table is set and the 3 irqs are now loaded from the
devicetree.

This series converts the lantiq target to clkdev amongst other things. The
driver needs to handle two clocks now. The fpi bus clock used to derive the
divider and the clock gate needed on some socs to make the secondary port work.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3809/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In doing the evt2irq() + muxed vector conversion for various port types
it became apparent that some of the legacy port types will presently
error out due to the irq requesting logic attempting to acquire the
non-existent BRI IRQ. This adds some sanity checks to the request/free
path to ensure that non-existence of a source in itself is not an error.

This should restore functionality for legacy PORT_SCI ports.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The support for CONFIG_MCA is being removed, since the 20
year old hardware simply isn't capable of meeting today's
software demands on CPU and memory resources.

This commit removes the MCA specific 8250 UART code.

Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-serial@vger.kernel.org
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Simplify serial data width calculation and adapt to bf609 LCR bit mask.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Change hardware flow control code to adapt to both bf5xx and bf60x.
Disabled serial device before set termios for bf60x.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Check if xmit buffer pointers are set to zero.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The serial4 controller on bf60x is an enhanced version of serial controller
on bf5xx. MMR size is 32 bits other than 16 bits. MMR GCTL, MCR and LCR are
combined into one control MMR. MSR and LSR are combined into one status MMR.

This patch adapts current bf5xx serial driver to serial4 controller on bf60x.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 64218087.

Buffer overruns are for hardware reported overruns, not software ones,
which will only happen if we run out of memory and you will get lots of
-ENOMEM errors at the same time.

Thanks to Alan Cox for catching this.
Reported-by: NAlan Cox <alan@linux.intel.com>
Cc: Corbin Atkinson <corbinat@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver is a module and needs module.h, otherwise it will break when
we remove a bogus usage of module.h from one of the other MIPS headers.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3447/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This driver is a module and needs module.h, otherwise it will break when we
remove a bogus usage of module.h from one of the other MIPS headers.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3446/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

If kzalloc() returns a NULL here, we pass a NULL to
xencons_disconnect_backend() which will cause an Oops.

Also I removed the __GFP_ZERO while I was at it since kzalloc() implies
__GFP_ZERO.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

3.4-rc introduced a regression when setting the LEDS. We do the right thing
but then return an error code.

Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=43144
Reported-by: Christian Casteyde
Signed-off-by: NAlan Cox <alan@linux/intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

3.4-rc introduced a regression when setting the LEDS. We do the right thing
but then return an error code.

Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=43144
Reported-by: Christian Casteyde
Signed-off-by: NAlan Cox <alan@linux/intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is legitimate but because we don't clear the drv->state pointer in the
unregister code causes a bogus BUG().

Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42880Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Cc: linux-serial@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Cc: linux-serial@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Using a single definition for the physical and virtual address register for all
variants boards clps711x. This patch also includes the use of a single function
clps_read/write in some units.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Cc: linux-serial@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NDong Aisheng <dong.aisheng@linaro.org>

The global wait_queue that is used for line discipline idle handling is
moved to a separate wait_queue for each line instance. This prevents
unnecessary blocking on one line, because of idle handling on another
line.
Signed-off-by: NIvo Sieben <meltedpianoman@gmail.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Update the 8250_em driver to support DT.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Update the 8250_em driver to correctly handle the case
where no clock is associated with the device.

The return value of clk_get() needs to be checked with
IS_ERR() to avoid NULL pointer referencing.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, serial drivers don't report buffer overruns. When a buffer overrun
occurs, tty_insert_flip_char returns 0, and no attempt is made to insert that
same character again (i.e. it is lost). This patch reports buffer overruns via
the buf_overrun field in the port's icount structure.
Signed-off-by: NCorbin Atkinson <corbin.atkinson@ni.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In theory we don't need it, in practice we are hitting some ill understood
deadlock when we don't drop it. The old code dropped it here so we are not
undoing anything problematic for pty. If pty could be unloaded it would be
a problem but it can't.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The PC BIOS does provide a NUMLOCK flag containing the desired state
of this LED. This patch sets the current state according to the data
in the bios.

[ hpa: fixed __weak declaration without definition, changed "inline"
  to "static inline" ]
Signed-Off-By: NJoshua Cov <joshuacov@googlemail.com>
Link: http://lkml.kernel.org/r/CAKL7Q7rvq87TNS1T_Km8fW_5OzS%2BSbYazLXKxW-6ztOxo3zorg@mail.gmail.comAcked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Commit d29f3ef3

    "tty_lock: Localise the lock"

added a tty arg to wait_event_interruptible_tty() but it missed
this arch specific instance for cris, causing a compile failure.

Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d29f3ef3 ("tty_lock: Localise the lock")
missed that d3a7b83f ("drivers/tty/amiserial.c:
add missing tty_unlock") just added a new caller of tty_unlock():

drivers/tty/amiserial.c: In function ‘set_serial_info’:
drivers/tty/amiserial.c:1077: error: too few arguments to function ‘tty_unlock’
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>