When doing a channel set or a reset operation the pending
frames queued up for transmission have to be flushed and
sent to mac80211. Fixing this has to be done in two separate
steps:

  * Flush queued frames and kill the URB TX completion handler.
  * Complete all the frames that in the TX pending queue.

This patch adds proper support for draining and all the callsites
namely, channel change/reset/idle/stop are fixed. A separate queue
is used for handling failed frames.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Maintain a bitmap of slots for transmission and update
the cookie field for every packet with the slot value.
This value would be used for matching packets when TX
completion processing is added.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to do endpoint header removal in the ISR.
Also, this is needed when TX slot management is added later on.
Use a helper function to strip the driver header.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A new routine that takes an endpoint explicitly is
introduced. The normal htc_send() now retrieves the endpoint
from the packet's private data. This would be useful
in TX completion when the endpoint ID would be required.
While at it, use a helper function to map the queue to endpoint.

Data/mgmt/beacon packets use htc_send(), while WMI comamnds
pass the endpoint to HTC.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Handle queue start/stop properly by maintaining
a counter to check if the pending frame count has
exceeded the threshold. Otherwise, packets would be
dropped needlessly. While at it, use a simple flag
to track queue status and use helper functions too.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using a single URB for receiving WMI events is
insufficient, increase it to 64 to not lose
WMI events in high throughput situations.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This event will be generated by the target for packet completions.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a new cookie field that would be filled by the host.
This can be used to match the TX status WMI event with
the appropriate packet.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current max queue length of 1024 is quite large
and unnecessary. 256 suffices well enough even for high
throughput situations.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For all packets sent through the USB_WLAN_TX_PIPE endpoint,
the private area of the SKB's tx_info can be used to store
driver-specific information. For packets sent through USB_REG_OUT_PIPE,
this will not make a difference since they are routed through a
separate routine that doesn't access the private region.

This would help in situations where TX information is required
in the URB callback.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

WMI_TGT_TXQ_ENABLE_CMDID
WMI_HOST_ATTACH
WMI_DEBUG_INFO_CMDID
WMI_BEACON_UPDATE_CMDID
WMI_RESET_CMDID
WMI_RX_LINK_CMDID
WMI_STOP_DMA_RECV_CMDID
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The length of the received SKB could be equal to
HTC_RX_FRAME_HEADER_SIZE in case of packets with phy/crc errors,
in which case they are dropped without being processed.
Fix this check so that the error counters are updated correctly.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use a queue to handle WMI events and schedule a tasklet
to process the events. This fixes the race between the
WMI event ISR and the SWBA tasklet when the arrival of
WMI events in quick succession could overwrite the SWBA
data before the tasklet from a previous iteration could
have been scheduled. Also, drain the WMI queue properly.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Transmission of beacons becomes erratic when TX load
is high, since the latency involved in the generation
of a SWBA interrupt on the target to the actual sending
of a beacon is quite high for USB devices.

Fix this by adjusting the beacon response time.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the CAB endpoint to send buffered multicast or
broadcast frames after each SWBA event.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set operating parameters (cwmin, cwmax) for the beacon queue
in AP mode.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In multi-interface mode, beacons/probe responses that are
sent out must have their timestamp field updated. Calculate
the TSF adjustment value for each beaconing interface and set it
in the frame properly.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Beacon transmission is now handled through a slot mechanism.
This allows multiple beaconing interfaces to be be present.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Match the beacon header with that of the firmware.
Also, the firmware reports the TSF for an SWBA, so
store it.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also, update the wiphy information and use the correct
device pointer when registering. This would fix ethtool.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the new FW requires backward incompatible host driver changes,
rename the FW to allow older driver versions to work with the
older FW.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All the AR7010 devices supoprted by ath9k_htc are based
on version v1.1, so remove support for v1.0.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently ath9k only available in menuconfig if PCI bus
support is enabled. However the driver is required for
the built-in wireless MACs of the Atheros AR9130/AR9132
SoCs. These SoCs have no PCI controller, the wireless
MAC is connected to the AHB bus on them.

Introduce separated config options for the supported
buses, in order to allow building of ath9h without PCI
bus support.

As a bonus, this patch removes the cross-reference of
the ATHEROS_AR71XX option which is not present in the
kernel.

Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently the device id in the platform driver is hardcoded to an id
which is specific to AR9130/AR9132 SOCs as it supports only wmac (wireless mac)
of these SOCs. But this needs to be dynamic when we want to support different
wmac of SOCs. So add id_table to driver to make it extendable to more SOCs.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes random disconnect.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check whether index is within bounds before testing the element
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check whether index is within bounds before testing the element

Both spurChans arrays in modalHeader5G and modalHeader2G have 5 elements,
AR_EEPROM_MODAL_SPURS is defined 5. So unless a break occurs, in the
last iteration (i=5) we tried to access spurChansPtr[5] before testing
whether i was within bounds. Fix this.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Older versions have not been sold and the driver does not explicitly
check for them anyway, so we can simply ignore the macRev here.
Reduces ath9k_hw size on mips by more than 2 KB.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: configure beacons based on hw opmode" introduced
a regression which leads to kernel panic. Failed to stop ani timer
during the driver unload while any of the beaconing vif is running.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>