TV-out uses the same reference clock as everyone else. The only
difference seems to be in the slightly different CB tuning limit.

Note that PLL_REF_INPUT_TVCLKINBC is a reserved value on ilk+. Also
strictly speaking we don't support native TV-out on ilk+, hence all
that code is dead. But Bspec still contains some residual mentions of
native TV-out on some pch-split platforms, so I've figured it doesn't
hurt to keep the code around a bit longer (e.g. in the cb tune
function).

v2: Improve the commit message as Jani suggested in his review.
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have a very nice infrastructure for this now!

Note that the multifunction sdvo support is pretty neatly broken: We
completely ignore userspace's request for which connector to wire up
with the encoder and just use whatever the last detect callback has
seen.

Not something I'll fix in this patch, but unfortunately something
which is also broken in the DDI code ...

v2: Don't call sdvo_tv_clock twice.
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There are no more users for these, so remove them.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

is_pch_edp() will be removed by the next patch, so replace it by a check
for the port and device type.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

is_pch_edp() will be removed in a follow-up patch, so replace it
with a check for the port and VBT info (for port-D eDP).

Also make things a bit clearer by using a switch on the ports.

v2:
- make the comment about not setting the conder type for DP clearer
  (Ville)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On ILK-IVB the CPU side eDP is always on port-A.

Also reduce somewhat the debug verbosity.

v2:
- reduce debug verbosity
Signed-off-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On HSW the CPU side eDP is always on port-A, the PCH side eDP is always
on port-D.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Works pretty well actually.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In some cases, we may not need GTT address space allocated to a stolen
object, so allow passing -1 to the preallocated function to indicate as
much.

v2: remove BUG_ON(gtt_offset & 4095) now that -1 is allowed (Ville)
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

But we need to get the right stolen base and make pre-allocated objects
for BIOS stuff so we don't clobber it.  If the BIOS hasn't allocated a
power context, we allocate one here too, from stolen space as required
by the docs.

v2: fix stolen to phys if ladder (Ben)
    keep BIOS reserved space out of allocator altogether (Ben)
v3: fix mask of stolen base (Ben)
v4: clean up preallocated object on unload (Ben)
    don't zero reg on unload (Jesse)
    fix mask harder (Jesse)
v5: use unref for freeing stolen bits (Chris)
    move alloc/free to intel_pm.c (Chris)
v6: NULL pctx at disable time so error paths work (Ben)
v7: use correct PCI device for config read (Jesse)
Reviewed-by: NBen Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If the calculated FBC watermark is no good, we simply disable FBC
watermarks. But we fail to re-enable them later if the calculated
watermark becomes good again. Fix that, but remember to leave FBC
watermarks disabled on ILK since that's required by some workarounds.

v2: Fix checkpatch complaint
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For the device to enter D3 we should enable PCH clock gating.

v2:
- use HAS_PCH_LPT instead of IS_HASWELL (Ville, Paolo)
- rename lpt_allow_clock_gating to lpt_suspend_hw (Paolo)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

commit 142e2398
Author: Egbert Eich <eich@suse.de>
Date:   Thu Apr 11 15:57:57 2013 +0200

    drm/i915: Add bit field to record which pins have received HPD events (v3)

added a bit field for hotplug event tracking. There ended up being three
different v3 of the patch: [1], [2], and [3]. Apparently [1] was the
correct one, but some frankenstein combination of the three got
committed, which reversed the logic for setting the hotplug bits and
misplaced a continue statement, skipping the hotplug irq storm handling
altogether.

This lead to broken hotplug detection, bisected to
commit 321a1b30
Author: Egbert Eich <eich@suse.de>
Date:   Thu Apr 11 16:00:26 2013 +0200

    drm/i915: Only reprobe display on encoder which has received an HPD event (v2)

which uses the incorrectly set hotplug event bits.

Fix the mess.

[1] http://mid.gmane.org/1366112220-7638-6-git-send-email-eich@suse.de
[2] http://mid.gmane.org/1365688677-13682-1-git-send-email-eich@suse.de
[3] http://mid.gmane.org/1365688996-13874-1-git-send-email-eich@suse.deSigned-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We did not mention the workaround name when implementing those. This
should help us track what we already implement.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We already have the same check on intel_enable_ddi. This patch
prevents "unclaimed register" messages when the power well is
disabled.

V2: Reset intel_crtc->eld_vld to false after the mode_set function.
V3: Add both "type != INTEL_OUTPUT_EDP" requested.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This fixes "unclaimed register" messages when the power well is
disabled and there's a GPU hang.

v2: Use the new intel_display_power_enabled().
v3: Use the new domains for intel_display_power_enabled().
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In the error state function we read the registers without checking if
the power well is on, so after doing this we have to clear the
FPGA_DBG_RM_NOCLAIM bit to prevent the next I915_WRITE from detecting
it and printing an error message.

The first version of this patch was checking for the power well state
and then avoiding reading registers that were off, but the reviewers
requested to just read the registers any way and then later clear the
FPGA_DBG_RM_NOCLAIM bit.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to dump these registers if we want to properly interpret the
others.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This should replace intel_using_power_well. The idea is that we're
adding the requested power domain as an argument, so this might enable
the code to look less platform-specific and also allows us to easily
add new domains in case we need.

v2: Add more domains to enum intel_display_power_domain
v3: Even more domains requested
Requested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Supposedly we should use the DAC divider for <300MHz pixel clocks, but as
that doesn't actually work as well as the high freq divider here in
practice, just use the high freq divider all the time.

v2: remove unconditional write (Jesse)
    check for pixel rate properly (Jesse)
v3: give up, the DAC divider apparently doesn't work, and low res modes
    work ok (Jesse)
    remove debug msg (Jesse)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NKenneth Graunke <kenneth@whitecape.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This regression was introduced in:

commit b074cec8
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Thu Apr 25 12:55:02 2013 -0700

    drm/i915: move PCH pfit controls into pipe_config

In refactoring this, it was only applied to eDP, which is incorrect.  In
fact, if we ever use the panel fitter to deal with overscan on HDMI,
we'll need to extend it again, so just drop the conditional altogether.

v2: drop check for eDP since we can use the fitter in any config (Daniel)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Both the docs and the existing code were wrong.  So fix both and use a
switch statement like we do elsewhere to make things simple & clear.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Instead of returning the cached value, which is just what the kernel
requested.
Reviewed-by: NKenneth Graunke <kenneth@whitecape.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Description:
intel_gmbus_is_forced_bit is no extern as its body is right below.
Likewise for intel_gmbus_is_port_valid.

This fixes a compilation issue with clang. An initial version of this patch
was developed by PaX Team <pageexec at freemail.hu>.
This is respin of this patch.

20130509: v2: (re-)add inline upon request.
Signed-off-by: NJan-Simon Möller <dl9pf@gmx.de>
CC: pageexec@freemail.hu
CC: daniel.vetter@ffwll.ch
CC: airlied@linux.ie
CC: intel-gfx@lists.freedesktop.org
CC: dri-devel@lists.freedesktop.org
CC: linux-kernel@vger.kernel.org
[danvet: Bikeshed commit message.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It also makes some sense IMO to have these two functions separate
irrespective of the number of callers.

Only the single caller for now, but that will change as we add more
PPGTTs.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because PPGTT PDEs within the GTT are calculated in cachelines
(HW guys consistency ftw) we do a divide which will wreak havoc if this
is wrong, and I know that from experience).

If/when we move to multiple PPGTTs this will have to become a WARN, and
return an error. For now however it should always be considered fatal,
and only a developer could hit it.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: s/BUG/WARN]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because our context refcounting doesn't grab a ref at lookup time, it is
unsafe to do so without the lock.

NOTE: We don't have an easy way to put the assertion in the lookup
function which is where this really belongs. Context switching is good
enough because it actually asserts even more correctness by protecting
the default_context.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: s/BUG/WARN/]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Only one caller. Also drop the intel_ prefix as is now customary for
platform specific and static functions.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

- PCH_ prefix for pch registers on ibx/cpt/ppt.
- Drop the DP_ from the link defines, redundant.
- Drop the GMCH from the data defines and instead give the special g4x
  registers a consistent _G4X postfix.

v2:
- Realign #defines and use tabs (Paulo).
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is possible thanks to moving the m/n stuff into pipe_config.

Unfortunately we need to move them a bit to avoid forward
declarations.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

While at it, also extract a common helper to copy the timings from the
cpu transcoder to the pch transcoder. That way it's really explicit
how the lpt transcoder is hardcoded.

v2:
- Re-align #defines properly (Paulo).
- Use cpu_transcoder when copying pipe timings (Paulo).
- s/intel_pch_transcoder_enable/intel_pch_transcoder_set_timings/
  since we already have a pch transcoder enable function, and this is
  clearer, too.
- Fixup 80 char line overflow in intel_display.c. I've opted to ignore
  this in i915_reg.h and i915_ums.c since meh.

Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Every time I read hsw code I get completely confused about this. So
call it what it is more explicitly.

Also, add an LPT_TRANSCONF for the pch transcoder A and use it in
lpt-only code, to really unconfuse me.

v2: s/plane/pipe/ in the TRANSCONF #define (Paulo).
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the hw state readout&check code it's important that the values we
keep around are the canonical ones. Unfortunately when adding the pipe
timings readout support I've missed that the write side adjusts the
timings in the pipe config.

Fix this up and so prevent the unsightly WARN noise in dmesg. This
regression has been introduced in

commit 1bd1bd80
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Mon Apr 29 21:56:12 2013 +0200

    drm/i915: hw state readout support for pipe timings
Reported-by: NPaulo Zanoni <przanoni@gmail.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Storing context reference into request struct
allows us to inspect context and its associated
objects when requests are retired.

Both ppgtt and arb robustness work will need
this.
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In order to be notified of when the context and all of its associated
objects is idle (for if the context maps to a ppgtt) we need a callback
from the retire handler. We can arrange this by using the kref_get/put
of the context for request tracking and by inserting a request to
demarque the switch away from the old context.

[Ben: fixed minor error to patch compile, AND s/last_context/from/]
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

dp_init_connector adjusts the encoder type if it is a eDP panel. Use
that to decide whether we should set up a hdmi connector or not.

To do so reorder the hdmi connector setup sequence in ddi_init a bit.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We can't read the pfit regs if the power well is off, so use the cached
value.

v2: re-add lost comment (Jesse)
    make sure the crtc using the fitter is actually enabled (Jesse)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Drop now unused dev_priv, as spotted by Mika.]
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>