net/core/skbuff.c is a hodge-podge of symbol export placement.
Some of the exports are right after the definition of the
symbol being exported, others are clumped together into a big
group at the end of the file.

Make things consistent.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current "RTNETLINK answers: Invalid argument" warning, while trying to
add multiq qdisc to non-multiqueue device, isn't very helpful and some
of these devs can be changed btw., so let's use a better errno.

With feedback from Stephen Hemminger <shemminger@vyatta.com>
Reported-by: NBadalian Vyacheslav <slavon@bigtelecom.ru>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This kills of HAVE_ALLOC_SKB and HAVE_ALIGNABLE_SKB.

Nothing in-tree uses them and nothing in-tree has used them
since 2.0.x times.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tx_timeout reset path needs to re-init dev and re-apply nic cfg to
enable vlan stripping.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report all bad FCS errs as frames errs.  This includes frames with bad
FCS on wire detected by MAC and frames which may be truncated due to
ingress FIFO overruns.  No longer print a driver msg on bad FCS err.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return notify intr credits after notify intr from firmware.  This is
especially important for legacy PCI intr mode, where not returning
credits would cause PBA to remain asserted which would get us right
back into the ISR.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/gianfar.c

PPP is modular code so no initdata on netns hooks.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

> Kernel BUG at drivers/net/tun.c:444
> invalid opcode: 0000 [1] SMP
> last sysfs file: /class/net/lo/ifindex
> CPU 0
> Modules linked in: tun ipt_MASQUERADE iptable_nat ip_nat xt_state ip_conntrack
> nfnetlink ipt_REJECT xt_tcpudp iptable_filter d
> Pid: 6912, comm: qemu-kvm Tainted: G      2.6.18-128.el5 #1
> RIP: 0010:[<ffffffff886f57b0>]  [<ffffffff886f57b0>]
> :tun:tun_chr_readv+0x2b1/0x3a6
> RSP: 0018:ffff8102202c5e48  EFLAGS: 00010246
> RAX: 0000000000000000 RBX: ffff8102202c5e98 RCX: 0000000004010000
> RDX: ffff810227063680 RSI: ffff8102202c5e9e RDI: ffff8102202c5e92
> RBP: 0000000000010ff6 R08: 0000000000000000 R09: 0000000000000001
> R10: ffff8102202c5e94 R11: 0000000000000202 R12: ffff8102275357c0
> R13: ffff81022755e500 R14: 0000000000000000 R15: ffff8102202c5ef8
> FS:  00002ae4398db980(0000) GS:ffffffff803ac000(0000) knlGS:0000000000000000
> CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
> CR2: 00002ae4ab514000 CR3: 0000000221344000 CR4: 00000000000026e0
> Process qemu-kvm (pid: 6912, threadinfo ffff8102202c4000, task
> ffff81022e58d820)
> Stack:  00000000498735cb ffff810229d1a3c0 0000000000000000 ffff81022e58d820
>  ffffffff8008a461 ffff81022755e528 ffff81022755e528 ffffffff8009f925
>  000005ea05ea0000 ffff8102209d0000 00001051143e1600 ffffffff8003c00e
> Call Trace:
>  [<ffffffff8008a461>] default_wake_function+0x0/0xe
>  [<ffffffff8009f925>] enqueue_hrtimer+0x55/0x70
>  [<ffffffff8003c00e>] hrtimer_start+0xbc/0xce
>  [<ffffffff886f58bf>] :tun:tun_chr_read+0x1a/0x1f
>  [<ffffffff8000b3f3>] vfs_read+0xcb/0x171
>  [<ffffffff800117d4>] sys_read+0x45/0x6e
>  [<ffffffff8005d116>] system_call+0x7e/0x83
>
>
> Code: 0f 0b 68 40 62 6f 88 c2 bc 01 f6 42 0a 08 74 0c 80 4c 24 41
> RIP  [<ffffffff886f57b0>] :tun:tun_chr_readv+0x2b1/0x3a6
>  RSP <ffff8102202c5e48>
>  <0>Kernel panic - not syncing: Fatal exception

This crashed when an LRO packet generated by bnx2x reached a
tun device through the bridge.  We're supposed to drop it at
the bridge.  However, because the check was placed in br_forward
instead of __br_forward, it's only effective if we are sending
the packet through a single port.

This patch fixes it by moving the check into __br_forward.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the user creates IPv6 over IPv6 tunnel, the device name created
by the kernel isn't set to t->parm.name, which is referred as the
result of ioctl().
Signed-off-by: NNoriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ira Snyder found that commit 8c7396ae
"gianfar: Merge Tx and Rx interrupt for scheduling clean up ring" can
cause hangs. It's because there was removed clearing of interrupts in
gfar_schedule_cleanup() (which is called by an interrupt handler) in
case when netif scheduling has been disabled. This patch brings back
this action and a comment.
Reported-by: NIra Snyder <iws@ovro.caltech.edu>
Reported-by: NPeter Korsgaard <jacmet@sunsite.dk>
Bisected-by: NIra Snyder <iws@ovro.caltech.edu>
Tested-by: NPeter Korsgaard <jacmet@sunsite.dk>
Tested-by: NIra Snyder <iws@ovro.caltech.edu>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When user tries to map all chunks given in argument, kernel
works on a copy of the chunkmap, but at the end it doesn't
check the copy, but the orginal one.
Signed-off-by: NQu Haoran <haoran.qu@6wind.com>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes echoing if the socket that has sent the request to
create/update/delete an entry is not subscribed to any multicast
group. With the current code, ctnetlink would not send the echo
message via unicast as nfnetlink_send() would be skip.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an inconsistency in the current ctnetlink code
since NAT sequence adjustment bit can only be updated but not set
in the conntrack entry creation.

This patch is used by conntrackd to successfully recover newly
created entries that represent connections with helpers and NAT
payload mangling.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes connection tracking handling for ICMPv6 messages
related to Stateless Address Autoconfiguration, MLD, and MLDv2. They
can not be tracked because they are massively using multicast (on
pre-defined address). But they are not invalid and should not be
detected as such.
Signed-off-by: NEric Leblond <eric@inl.fr>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch fixes a typo in the inverse mapping of Node Information
request. Following draft-ietf-ipngwg-icmp-name-lookups-09, "Querier"
sends a type 139 (ICMPV6_NI_QUERY) packet to "Responder" which answer
with a type 140 (ICMPV6_NI_REPLY) packet.
Signed-off-by: NEric Leblond <eric@inl.fr>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the crystal frequency calculations in the b2062 init code.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A few bugs were fixed in the LP baseband init specs.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for the SSB PMU.
A PMU is found on Low-Power devices.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

pos[4] can't be both 0x43 and 0x04, 2nd should be pos[5]
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In certain cases it is required to perform board specific actions
before activating libertas G-SPI interface. These actions may include
power up of the chip, GPIOs setup, proper pin-strapping and SPI
controller config.
This patch adds ability to call board specific setup/teardown methods
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NAndrey Yurovsky <andrey@cozybit.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no point having the bss information of currently associated AP
when the AP is detected to be out of range.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The nl80211 rule flags were being used.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds initialization code for the 2062 radio.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds code for the baseband init of LP-PHY >=2.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixed led device naming for the iwlwifi (iwl-3945) driver. Due
to the documentation of the led subsystem/class the naming should
be "devicename:colour:function" while not applying sections
should be left blank.

This should lead to e.g. "iwl-%s::RX" instead of "iwl-%s:RX".
Signed-off-by: NDanny Kukawka <dkukawka@suse.de>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixed led device naming for the rt2x00 driver. Due to the
documentation of the led subsystem/class the naming should be
"devicename:colour:function" while not applying sections
should be left blank.

This should lead to e.g. "%s::radio" instead of "%s:radio".
Signed-off-by: NDanny Kukawka <dkukawka@suse.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixed led device naming for the b43legacy driver. Due to the
documentation of the led subsystem/class the naming should be
"devicename:colour:function" while not applying sections
should be left blank.

This should lead to e.g. "b43legacy-%s::rx" instead of
"b43legacy-%s:rx".
Signed-off-by: NDanny Kukawka <dkukawka@suse.de>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixed led device naming for the ath9k driver. Due to the
documentation of the led subsystem/class the naming should be
"devicename:colour:function" while not applying sections
should be left blank.

This should lead to e.g. "ath9k-%s::rx" instead of "ath9k-%s:rx".
Signed-off-by: NDanny Kukawka <dkukawka@suse.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds register definitions for the LP-PHY.
This also adds a few minor empty function bodies for the LP-init.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This lets userspace request to get the currently set
regulatory domain.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Monitor mode is able to TX by using injected frames. We should
not allow injected frames to be sent unless allowed by regulatory
rules. Since AP mode uses a monitor interfaces to transmit
management frames we have to take care to not break AP mode as
well while resolving this. We can deal with this by allowing compliant
APs solutions to inform mac80211 if their monitor interface is
intended to be used for an AP by setting a cfg80211 flag for the
monitor interface. hostapd, for example, currently does its own
checks to ensure AP mode is not used on channels which require radar
detection. Once such solutions are available it can can add this
flag for monitor interfaces.
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also call our own ieee80211_master_setup routine instead of
overwriting almost all the values from ether_setup; this
loses a few assignments that are pointless on the master
interface anyway.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert to new net_device_ops in 2.6.28 and later.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Giving the signal in dB isn't much more useful to userspace
than giving the signal in unspecified units. This removes
some radiotap information for zd1211 (the only driver using
this flag), but it helps a lot for getting cfg80211-based
scanning which won't support dB, and zd1211 being dB is a
little fishy anyway.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>