Any arm64 based parts that have cache aliasing issues can set it
manually.  Apparently dragged in from ARM(32) defaults in commit
8c2c3df3 "arm64: Build infrastructure".
Signed-off-by: NKim Phillips <kim.phillips@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

The make rpm target depends on proper UTS_MACHINE definition.  Also, use
the variable in arch/arm64/kernel/setup.c, so that it's not accidentally
removed in the future.
Reported-and-tested-by: NFabian Vogt <fvogt@suse.com>
Signed-off-by: NMichal Marek <mmarek@suse.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Cortex-A53 erratum 843419 is worked around by the linker, although it is
a configure-time option to GCC as to whether ld is actually asked to
apply the workaround or not.

This patch ensures that we pass --fix-cortex-a53-843419 to the linker
when both CONFIG_ARM64_ERRATUM_843419=y and the linker supports the
option.
Acked-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Now that we use the MPIDR to resume on the same CPU that we hibernated on,
we no longer need to refuse to hibernate if the boot cpu is offline. (Which
we can't possibly know if kexec causes logical CPUs to be renumbered).

This reverts commit 1fe492ce.
Signed-off-by: NJames Morse <james.morse@arm.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

disable_nonboot_cpus() assumes that the lowest numbered online CPU is
the boot CPU, and that this is the correct CPU to run any power
management code on.

On arm64 CPU0 can be taken offline. For hibernate/resume this means we
may hibernate on a CPU other than CPU0. If the system is rebooted with
kexec 'CPU0' will be assigned to a different CPU. This complicates
hibernate/resume as now we can't trust the CPU numbers.

We currently forbid hibernate if CPU0 has been hotplugged out to avoid
this situation without kexec.

Save the MPIDR of the CPU we hibernated on in the hibernate arch-header,
use hibernate_resume_nonboot_cpu_disable() to direct which CPU we should
resume on based on the MPIDR of the CPU we hibernated on. This allows us to
hibernate/resume on any CPU, even if the logical numbers have been
shuffled by kexec.
Signed-off-by: NJames Morse <james.morse@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

disable_nonboot_cpus() assumes that the lowest numbered online CPU is
the boot CPU, and that this is the correct CPU to run any power
management code on.

On x86 this is always correct, as CPU0 cannot (easily) by taken offline.

On arm64 CPU0 can be taken offline. For hibernate/resume this means we
may hibernate on a CPU other than CPU0. If the system is rebooted with
kexec 'CPU0' will be assigned to a different physical CPU. This
complicates hibernate/resume as now we can't trust the CPU numbers.
Arch code can find the correct physical CPU, and ensure it is online
before resume from hibernate begins, but also needs to influence
disable_nonboot_cpus()s choice of CPU.

Rename disable_nonboot_cpus() as freeze_secondary_cpus() and add an
argument indicating which CPU should be left standing. Follow the logic
in migrate_to_reboot_cpu() to use the lowest numbered online CPU if the
requested CPU is not online.
Add disable_nonboot_cpus() as an inline function that has the existing
behaviour.

Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Follow the example set by x86 in commit 9ccaf77c ("x86/mm:
Always enable CONFIG_DEBUG_RODATA and remove the Kconfig option"), and
make these protections a fundamental security feature rather than an
opt-in. This also results in a minor code simplification.

For those rare cases when users wish to disable this protection (e.g.
for debugging), this can be done by passing 'rodata=off' on the command
line.

As DEBUG_RODATA_ALIGN is only intended to address a performance/memory
tradeoff, and does not affect correctness, this is left user-selectable.
DEBUG_MODULE_RONX is also left user-selectable until the core code
provides a boot-time option to disable the protection for debugging
use-cases.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: NKees Cook <keescook@chromium.org>
Acked-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Kdump(kexec-tools) parses /proc/iomem to identify all the memory regions
on the system. Since the current kernel names "nomap" regions, like UEFI
runtime services code/data, as "System RAM," kexec-tools sets up elf core
header to include them in a crash dump file (/proc/vmcore).

Then crash dump kernel parses UEFI memory map again, re-marks those regions
as "nomap" and does not create a memory mapping for them unlike the other
areas of System RAM. In this case, copying /proc/vmcore through
copy_oldmem_page() on crash dump kernel will end up with a kernel abort,
as reported in [1].

This patch names all the "nomap" regions explicitly as "reserved" so that
we can exclude them from a crash dump file. acpi_os_ioremap() must also
be modified because those regions have WB attributes [2].

Apart from kdump, this change also matches x86's use of acpi (and
/proc/iomem).

[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2016-August/448186.html
[2] http://lists.infradead.org/pipermail/linux-arm-kernel/2016-August/450089.htmlReviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Tested-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NAKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

DEBUG_PAGEALLOC removes the valid bit of page table entries to prevent
any access to unallocated memory. Hibernate uses this as a hint that those
pages don't need to be saved/restored. This patch adds the
kernel_page_present() function it uses.

hibernate.c copies the resume kernel's linear map for use during restore.
Add _copy_pte() to fill-in the holes made by DEBUG_PAGEALLOC in the resume
kernel, so we can restore data the original kernel had at these addresses.

Finally, DEBUG_PAGEALLOC means the linear-map alias of KERNEL_START to
KERNEL_END may have holes in it, so we can't lazily clean this whole
area to the PoC. Only clean the new mmuoff region, and the kernel/kvm
idmaps.

This reverts commit da24eb1f.
Reported-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NJames Morse <james.morse@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Resume from hibernate needs to clean any text executed by the kernel with
the MMU off to the PoC. Collect these functions together into the
.idmap.text section as all this code is tightly coupled and also needs
the same cleaning after resume.

Data is more complicated, secondary_holding_pen_release is written with
the MMU on, clean and invalidated, then read with the MMU off. In contrast
__boot_cpu_mode is written with the MMU off, the corresponding cache line
is invalidated, so when we read it with the MMU on we don't get stale data.
These cache maintenance operations conflict with each other if the values
are within a Cache Writeback Granule (CWG) of each other.
Collect the data into two sections .mmuoff.data.read and .mmuoff.data.write,
the linker script ensures mmuoff.data.write section is aligned to the
architectural maximum CWG of 2KB.
Signed-off-by: NJames Morse <james.morse@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Each time new section markers are added, kernel/vmlinux.ld.S is updated,
and new extern char __start_foo[] definitions are scattered through the
tree.

Create asm/include/sections.h to collect these definitions (and include
the existing asm-generic version).
Signed-off-by: NJames Morse <james.morse@arm.com>
Reviewed-by: NMark Rutland <mark.rutland@arm.com>
Tested-by: NMark Rutland <mark.rutland@arm.com>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

The ARMv8 architecture allows execute-only user permissions by clearing
the PTE_UXN and PTE_USER bits. However, the kernel running on a CPU
implementation without User Access Override (ARMv8.2 onwards) can still
access such page, so execute-only page permission does not protect
against read(2)/write(2) etc. accesses. Systems requiring such
protection must enable features like SECCOMP.

This patch changes the arm64 __P100 and __S100 protection_map[] macros
to the new __PAGE_EXECONLY attributes. A side effect is that
pte_user() no longer triggers for __PAGE_EXECONLY since PTE_USER isn't
set. To work around this, the check is done on the PTE_NG bit via the
pte_ng() macro. VM_READ is also checked now for page faults.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Whenever we are hitting a kprobe from a none-kprobe debug exception handler,
we hit an infinite occurrences of "Unexpected kernel single-step exception
at EL1"

PSTATE.D is debug exception mask bit. It is set whenever we enter into an
exception mode. When it is set then Watchpoint, Breakpoint, and Software
Step exceptions are masked. However, software Breakpoint Instruction
exceptions can never be masked. Therefore, if we ever execute a BRK
instruction, irrespective of D-bit setting, we will be receiving a
corresponding breakpoint exception.

For example:

- We are executing kprobe pre/post handler, and kprobe has been inserted in
  one of the instruction of a function called by handler. So, it executes
  BRK instruction and we land into the case of KPROBE_REENTER. (This case is
  already handled by current code)

- We are executing uprobe handler or any other BRK handler such as in
  WARN_ON (BRK BUG_BRK_IMM), and we trace that path using kprobe.So, we
  enter into kprobe breakpoint handler,from another BRK handler.(This case
  is not being handled currently)

In all such cases kprobe breakpoint exception will be raised when we were
already in debug exception mode. SPSR's D bit (bit 9) shows the value of
PSTATE.D immediately before the exception was taken. So, in above example
cases we would find it set in kprobe breakpoint handler.  Single step
exception will always be followed by a kprobe breakpoint exception.However,
it will only be raised gracefully if we clear D bit while returning from
breakpoint exception.  If D bit is set then, it results into undefined
exception and when it's handler enables dbg then single step exception is
generated, however it will never be handled(because address does not match
and therefore treated as unexpected).

This patch clears D-flag unconditionally in setup_singlestep, so that we can
always get single step exception correctly after returning from breakpoint
exception. Additionally, it also removes D-flag set statement for
KPROBE_REENTER return path, because debug exception for KPROBE_REENTER will
always take place in a debug exception state. So, D-flag will already be set
in this case.
Acked-by: NSandeepa Prabhu <sandeepa.s.prabhu@gmail.com>
Acked-by: NMasami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: NPratyush Anand <panand@redhat.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Currently, x25 and x26 hold the physical addresses of idmap_pg_dir
and swapper_pg_dir, respectively, when running early boot code. But
having registers with 'global' scope in files that contain different
sections with different lifetimes, and that are called by different
CPUs at different times is a bit messy, especially since stashing the
values does not buy us anything in terms of code size or clarity.

So simply replace each reference to x25 or x26 with an adrp instruction
referring to idmap_pg_dir or swapper_pg_dir directly.
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

These objects are set during initialization, thereafter are read only.

Previously I only want to mark vdso_pages, vdso_spec, vectors_page and
cpu_ops as __read_mostly from performance point of view. Then inspired
by Kees's patch[1] to apply more __ro_after_init for arm, I think it's
better to mark them as __ro_after_init. What's more, I find some more
objects are also read only after init. So apply __ro_after_init to all
of them.

This patch also removes global vdso_pagelist and tries to clean up
vdso_spec[] assignment code.

[1] http://www.spinics.net/lists/arm-kernel/msg523188.htmlAcked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

The vm_special_mapping spec which is used for aarch32 vectors page is
never modified, so mark it as const.
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

It is not needed after booting, this patch moves the alloc_vectors_page
function to the __init section.
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

HAVE_CLK is select'ed by CLKDEV_LOOKUP, which is select'ed by
COMMON_CLK, which is select'ed by ARM64.  No sub-architecture
needs to select HAVE_CLK explicitly.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Even though perf_ops_bp was removed/renamed back in commit
b0a873eb ("perf: Register PMU implementations"), as part of
v2.6.37, its definition still lives on in some arch headers.

This patch removes the vestigal definition from arm64.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Use the builtin_platform_driver() to simplify code.
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

__dma_* routines have been converted to use start and size instread of
start and end addresses. The patch was origianlly for adding
__clean_dcache_area_poc() which will be used in pmem driver to clean
dcache to the PoC(Point of Coherency) in arch_wb_cache_pmem().

The functionality of __clean_dcache_area_poc()  was equivalent to
__dma_clean_range(). The difference was __dma_clean_range() uses the end
address, but __clean_dcache_area_poc() uses the size to clean.

Thus, __clean_dcache_area_poc() has been revised with a fallthrough
function of __dma_clean_range() after the change that __dma_* routines
use start and size instead of using start and end.

As a consequence of using start and size, the name of __dma_* routines
has also been altered following the terminology below:
    area: takes a start and size
    range: takes a start and end
Reviewed-by: NRobin Murphy <robin.murphy@arm.com>
Signed-off-by: NKwangwoo Lee <kwangwoo.lee@sk.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Currently ret_fast_syscall, work_pending, and ret_to_user form an ad-hoc
state machine that can be difficult to reason about due to duplicated
code and a large number of branch targets.

This patch factors the common logic out into the existing
do_notify_resume function, converting the code to C in the process,
making the code more legible.

This patch tries to closely mirror the existing behaviour while using
the usual C control flow primitives. As local_irq_{disable,enable} may
be instrumented, we balance exception entry (where we will almost most
likely enable IRQs) with a call to trace_hardirqs_on just before the
return to userspace.
Signed-off-by: NChris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

In break_before_make_ttbr_switch we perform broadcast TLB maintenance
for the inner shareable domain, and use a DSB ISH to complete this.
However, at the point we execute this, secondary CPUs are either
physically offline, or executing code outside of the kernel. Upon
entering the kernel, secondary CPUs will invalidate their TLBs before
enabling their MMUs.

Thus we do not need to invalidate TLBs of other CPUs, and as with
idmap_cpu_replace_ttbr1 we can reduce the scope of maintenance to the
TLBs of the local CPU. This keeps our TLB maintenance code consistent,
and is a minor optimisation.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Pull two parisc fixes from Helge Deller:
 "The first patch ensures that the high-res cr16 clocksource (which was
  added in kernel 4.7) gets choosen as default clocksource for parisc.

  The second patch moves the #define of EREFUSED down inside errno.h and
  thus unbreaks building the gccgo compiler"

* 'parisc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix order of EREFUSED define in errno.h
  parisc: Fix automatic selection of cr16 clocksource

This is an entirely new driver instead of yet another set of patches
to sb_edac.c because:

1) Mapping from PCI devices to socket/memory controller is significantly
   different. Skylake scatters devices on a socket across a number of
   PCI buses.
2) There is an extra level of interleaving via the "mcroute" register
   that would be a little messy to squeeze into the old driver.
3) Validation is getting too expensive. Changes to sb_edac need to
   be checked against Sandy Bridge, Ivy Bridge, Haswell, Broadwell and
   Knights Landing.
Acked-by: NAristeu Rozanski <aris@redhat.com>
Acked-by: NBorislav Petkov <bp@suse.de>
Signed-off-by: NTony Luck <tony.luck@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When building gccgo in userspace, errno.h gets parsed and the go include file
sysinfo.go is generated.

Since EREFUSED is defined to the same value as ECONNREFUSED, and ECONNREFUSED
is defined later on in errno.h, this leads to go complaining that EREFUSED
isn't defined yet.

Fix this trivial problem by moving the define of EREFUSED down after
ECONNREFUSED in errno.h (and clean up the indenting while touching this line).
Signed-off-by: NHelge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org

Commit 54b66800 (parisc: Add native high-resolution sched_clock()
implementation) added support to use the CPU-internal cr16 counters as reliable
clocksource with the help of HAVE_UNSTABLE_SCHED_CLOCK.

Sadly the commit missed to remove the hack which prevented cr16 to become the
default clocksource even on SMP systems.
Signed-off-by: NHelge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 4.7+

The kernel test robot reported a usercopy failure in the new hardened
sanity checks, due to a page-crossing copy of the FPU state into the
task structure.

This happened because the kernel test robot was testing with SLOB, which
doesn't actually do the required book-keeping for slab allocations, and
as a result the hardening code didn't realize that the task struct
allocation was one single allocation - and the sanity checks fail.

Since SLOB doesn't even claim to support hardening (and you really
shouldn't use it), the straightforward solution is to just make the
usercopy hardening code depend on the allocator supporting it.
Reported-by: Nkernel test robot <xiaolong.ye@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull i2c fixes from Wolfram Sang:
 "I2C has some pretty standard driver bugfixes and one minor cleanup"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: meson: Use complete() instead of complete_all()
  i2c: brcmstb: Use complete() instead of complete_all()
  i2c: bcm-kona: Use complete() instead of complete_all()
  i2c: bcm-iproc: Use complete() instead of complete_all()
  i2c: at91: fix support of the "alternative command" feature
  i2c: ocores: add missed clk_disable_unprepare() on failure paths
  i2c: cros-ec-tunnel: Fix usage of cros_ec_cmd_xfer()
  i2c: mux: demux-pinctrl: properly roll back when adding adapter fails

Pull device mapper fixes from Mike Snitzer:

 - a stable fix for DM round robin multipath path selector to disable
   preemption before using this_cpu_ptr()

 - a slight increase in DM crypt's mempool reserves to make swap ontop
   of DM crypt more performant

 - a few DM raid fixes to issues found while testing changes that were
   merged in v4.8-rc1

* tag 'dm-4.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm raid: support raid0 with missing metadata devices
  dm raid: enhance attempt_restore_of_faulty_devices() to support more devices
  dm raid: fix restoring of failed devices regression
  dm raid: fix frozen recovery regression
  dm crypt: increase mempool reserve to better support swapping
  dm round robin: do not use this_cpu_ptr() without having preemption disabled

Pull SCSI fixes from James Bottomley:
 "Six fairly small fixes.  The ipr, mpt3sas and ses ones all trigger
  oopses.  The megaraid one fixes an attach failure on io mapped only
  cards, the fcoe one is an obvious problem in the error path and the
  aacraid one is a theoretical security issue (ability to trick the
  kernel into a buffer overrun)"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  ses: Fix racy cleanup of /sys in remove_dev()
  mpt3sas: Fix resume on WarpDrive flash cards
  ipr: Fix sync scsi scan
  megaraid_sas: Fix probing cards without io port
  aacraid: Check size values after double-fetch from user
  fcoe: Use kfree_skb() instead of kfree()

Pull USB fixes from Greg KH:
 "Here are a number of USB fixes for reported issues for your tree.

  The normal amount of gadget fixes, xhci fixes, new device ids, and a
  few other minor things.  All of them have been in linux-next for a
  while, the full details are in the shortlog below"

* tag 'usb-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (43 commits)
  xhci: don't dereference a xhci member after removing xhci
  usb: xhci: Fix panic if disconnect
  xhci: really enqueue zero length TRBs.
  xhci: always handle "Command Ring Stopped" events
  cdc-acm: fix wrong pipe type on rx interrupt xfers
  usb: misc: usbtest: add fix for driver hang
  usb: dwc3: gadget: stop processing on HWO set
  usb: dwc3: don't set last bit for ISOC endpoints
  usb: gadget: rndis: free response queue during REMOTE_NDIS_RESET_MSG
  usb: udc: core: fix error handling
  usb: gadget: fsl_qe_udc: off by one in setup_received_handle()
  usb/gadget: fix gadgetfs aio support.
  usb: gadget: composite: Fix return value in case of error
  usb: gadget: uvc: Fix return value in case of error
  usb: gadget: fix check in sync read from ep in gadgetfs
  usb: misc: usbtest: usbtest_do_ioctl may return positive integer
  usb: dwc3: fix missing platform_set_drvdata() in dwc3_of_simple_probe()
  usb: phy: omap-otg: Fix missing platform_set_drvdata() in omap_otg_probe()
  usb: gadget: configfs: add mutex lock before unregister gadget
  usb: gadget: u_ether: fix dereference after null check coverify warning
  ...

Merge tag 'xfs-iomap-for-linus-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs

Pull xfs and iomap fixes from Dave Chinner:
 "Changes in this update:

  Regression fixes for XFS changes introduce in 4.8-rc1:
   - buffer IO accounting assert failure
   - ENOSPC block accounting reservation issue
   - DAX IO path page cache invalidation fix
   - rmapbt on-disk block count in agf
   - correct classification of rmap block type when updating AGFL.
   - iomap support for attribute fork mapping

  Regression fixes for iomap infrastructure in 4.8-rc1:
   - fiemap: honor FIEMAP_FLAG_SYNC
   - fiemap: implement FIEMAP_FLAG_XATTR support to fix XFS regression
   - make mark_page_accessed and pagefault_disable usage consistent with
     other IO paths"

* tag 'xfs-iomap-for-linus-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
  xfs: remove OWN_AG rmap when allocating a block from the AGFL
  xfs: (re-)implement FIEMAP_FLAG_XATTR
  xfs: simplify xfs_file_iomap_begin
  iomap: mark ->iomap_end as optional
  iomap: prepare iomap_fiemap for attribute mappings
  iomap: fiemap should honor the FIEMAP_FLAG_SYNC flag
  iomap: remove superflous pagefault_disable from iomap_write_actor
  iomap: remove superflous mark_page_accessed from iomap_write_actor
  xfs: store rmapbt block count in the AGF
  xfs: don't invalidate whole file on DAX read/write
  xfs: fix bogus space reservation in xfs_iomap_write_allocate
  xfs: don't assert fail on non-async buffers on ioacct decrement

Merge tag 'hwmon-for-linus-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "Fix a bug in it87 driver and URLs in ftsteutates driver"

* tag 'hwmon-for-linus-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (ftsteutates) Correct ftp urls in driver documentation
  hwmon: (it87) Features mask must be 32 bit wide

Pull more drm fixes from Dave Airlie:
 "Daniel pointed out I'd missed some i915 fixes, and I also found a
  single etnaviv fix I missed.

  So here they are"

* tag 'drm-fixes-for-4.8-rc3-2' of git://people.freedesktop.org/~airlied/linux:
  drm/etnaviv: take GPU lock later in the submit process
  drm/i915: Fix modeset handling during gpu reset, v5.
  drm/i915: fix aliasing_ppgtt leak
  drm/i915: fix WaInsertDummyPushConstPs
  drm/i915: Fix iboost setting for SKL Y/U DP DDI buffer translation entry 2
  drm/i915/gen9: Give one extra block per line for SKL plane WM calculations
  drm/i915: Acquire audio powerwell for HD-Audio registers
  drm/i915: Add missing rpm wakelock to GGTT pread
  drm/i915/fbc: FBC causes display flicker when VT-d is enabled on Skylake
  drm/i915: Clean up the extra RPM ref on CHV with i915.enable_rc6=0
  drm/i915: Program iboost settings for HDMI/DVI on SKL
  drm/i915: Fix iboost setting for DDI with 4 lanes on SKL
  drm/i915: Handle ENOSPC after failing to insert a mappable node
  drm/i915: Flush GT idle status upon reset

Pull DeviceTree fixes from Rob Herring:

 - a couple of DT node ref counting fixes

 - fix __unflatten_device_tree for PPC PCI hotplug case

 - rework marking irq controllers as OF_POPULATED in cases where real
   driver is used.

 - disable of_platform_default_populate_init on PPC.  The change in
   initcall order causes problems which need to be sorted out later.

* tag 'devicetree-fixes-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of: fix reference counting in of_graph_get_endpoint_by_regs
  of/platform: disable the of_platform_default_populate_init() for all the ppc boards
  ARM: imx6: mark GPC node as not populated after irq init to probe pm domain driver
  of/irq: Mark interrupt controllers as populated before initialisation
  drivers/of: Validate device node in __unflatten_device_tree()
  of: Delete an unnecessary check before the function call "of_node_put"

Pull documentation fixes from Jonathan Corbet:
 "Three small fixes for Sphinx-formatted documentation generation"

* tag '4.8-doc-fixes' of git://git.lwn.net/linux:
  doc-rst: customize RTD theme, drop padding of inline literal
  docs: kernel-documentation: remove some highlight directives
  docs: Set the Sphinx default highlight language to "guess"

Collection of i915 fixes.

* tag 'drm-intel-fixes-2016-08-15' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Fix modeset handling during gpu reset, v5.
  drm/i915: fix aliasing_ppgtt leak
  drm/i915: fix WaInsertDummyPushConstPs
  drm/i915: Fix iboost setting for SKL Y/U DP DDI buffer translation entry 2
  drm/i915/gen9: Give one extra block per line for SKL plane WM calculations
  drm/i915: Acquire audio powerwell for HD-Audio registers
  drm/i915: Add missing rpm wakelock to GGTT pread
  drm/i915/fbc: FBC causes display flicker when VT-d is enabled on Skylake
  drm/i915: Clean up the extra RPM ref on CHV with i915.enable_rc6=0
  drm/i915: Program iboost settings for HDMI/DVI on SKL
  drm/i915: Fix iboost setting for DDI with 4 lanes on SKL
  drm/i915: Handle ENOSPC after failing to insert a mappable node
  drm/i915: Flush GT idle status upon reset

Single GPU recovery fix
* 'drm-etnaviv-fixes' of git://git.pengutronix.de/git/lst/linux:
  drm/etnaviv: take GPU lock later in the submit process