Since the op_mode is leaving, the transport should set
its pointer to it to NULL to not point to freed memory.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The FH (DMA engine) tells the driver the index of the last
ready (closed) Rx buffer. This data is in closed_rb_num.
If we read this data several times we may get inconsistencies
between the code and the debug prints which can make it
harder to debug issues here.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

iwl-trans.h was included twice.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will allow to reduce slightly the number of interrupts
without sacrificing too much the latency in the Rx path.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It is not used outside pcie/rx.c.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Really trivial clean up.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Also, prefer the if(!X) notation over if(X == 0).
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When software crypto is enabled, it isn't safe
to enable MFP since the firmware interprets some
management packets, and with MFP it would do so
without proper validation.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

One one just a wrapper of the second, squash them.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Rename static functions. Function moved from trans.c to
tx.c. A few could be made static, others had to be exported.

Functions that implement the transport API are prefixed by
iwl_trans_pcie_, the others by iwl_pcie_.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Functions that implement the transport API are prefixed by
iwl_trans_pcie_, the others by iwl_pcie_.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Rename static functions. Function moved from trans.c to
rx.c. A few could be made static, others had to be exported.
Also, don't use rxb or rxbuf, but rb which stands for receive
buffer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is its natural place
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

1) s/tx_queue/txq
	for the sake of consistency.

2) s/rx_queue/rxq
	for the sake of consistency.

3) Make all functions begin with iwl_pcie_
	iwl_queue_init and iwl_queue_space are an exception
	since they are not PCIE specific although they are in
	pcie subdir.

4) s/trans_pcie_get_cmd_string/get_cmd_string
	it is much shorter and used in debug prints which
	are long lines.

5) s/iwl_bg_rx_replenish/iwl_pcie_rx_replenish_work
	this better emphasizes that it is a work

6) remove invalid kernelDOC markers

pcie/tx.c and pcie/trans.c still needs to be cleaned up.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is not needed, the comment there was wrong, it
is only needed when MSI was *not* enabled.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The allocation failure will already be very verbose.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a firmware error occurs, don't just abort synchronous
commands but also return an error (-EIO) and block any new
commands as well. Currently, an error is only returned if
WANT_SKB was set which is confusing and can lead to issues.

Blocking is done until a new firmware image is loaded.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The printk message should say RX, not TX.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to print the PCI resource
length and base address, nor the hardware
revision ID (which can be found in lspci)
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no reason to print these all the time,
the messages aren't all that interesting. Leave
them as DEBUG_INFO though, just in case.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the EEPROM reading was successful, don't print
a message by default, the EEPROM version isn't all
that interesting. Change the message to DEBUG_INFO
priority so it can still be obtained.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

People tend not to set the fields they want to leave as 0.
So make sure the struct is zeroed properly.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The ALIVE response of new fw inclues the base address of
the SCD in SRAM. Until we read it from a prph register,
which was set by the fw. Since the fw might well stop
updating the prph register, add a WARN when there is an
inconsitency between the ALIVE response and the register
to catch any change in the behavior.
Reviewed-by: NGregory Greenman <gregory.greenman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of open-coding it with a temporary list_head
pointer, just use list_first_entry.
Reviewed-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The flush_control parameter to iwlagn_txfifo_flush
is passed as an internal value (context flags) and
then sent to the device, that can't be right.

Fix the confusion by removing the parameter, always
use IWL_DROP_ALL that is redefined according to the
firmware API in the flush control.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no reason to clear the CTL_AMPDU flag on
transmitted frame status, it's not used by the
driver here and mac80211 only uses it for some
rate statistics.

Also remove a stray space in the function.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The flush command really flushes queues, not
FIFOs, and the first 32 bits indicate the
queues to flush, not FIFOs. Change the command
accordingly.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we unregister from mac80211 it will down the device anyway.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

No HCMD can be sent while RFKILL is asserted. If a SYNC
command is running while RFKILL is asserted the fw will
silently discard it. This means that the driver needs to
wake the process that sleeps on the CMD_SYNC.

Since the RFKILL interrupt is handled in the transport layer
and the code that sleeps in CMD_SYNC is also in the transport
layer, all this logic can be handled there.
This simplifies the work of the op_mode.

So the transport layer will now return -ERFKILL when a CMD
is sent and RFKILL is asserted. This will be the case even
when the CMD is SYNC. The transport layer will return
-ERFKILL straight away.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Clarify the documentation to indicate that these
flags can only be used at the end, i.e. after them
a copy TFD (no flags set) is invalid.
Reported-by: NInbal Hacohen <inbal.hacohen@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In addition to the NOCOPY flag, add a DUP flag that
tells the transport to kmemdup() the buffer and free
it after the command completes.

Currently this is only supported for a single buffer
in a given command, but that could be extended if it
should be needed.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remove the Kconfig option CONFIG_IWLWIFI_EXPERIMENTAL_MFP,
if the firmware doesn't support MFP then the user shouldn't
have the option to enable it as it won't work correctly.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since the queue might not be empty, we need to free the
pending Tx packets.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This can happen when we shut down suddenly an interface.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Once in bus enumeration is enough, no need to print it
again when the op_mode loads.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Doing the opposite is wrong, the SCD wouldn't like someone
to clear its data while the queue is still active.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of hardcoding the expression, use the macro
provided in the previous patch.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we disable a queue, we don't want the SCD to remember anything
about this queue (what packet was transmitted but not acked, what
packed was acked etc...).
Wipe out all this data in its SRAM.

Constify the arguments to iwl_write_targ_mem_dwords on the way.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>