Add pci_enable_device() to aec62xx probe function
before doing any I/O.

Original probe function tries to read from device's
PCI region 4 before calling ide_setup_pci_device().
Since the device is not enabled at this point,
on machines that have no firmware PCI initialization
(e.g. ASUS WL-700gE router), corresponding PCI BAR 
is 0 and the following inb() causes a kernel oops.
Signed-off-by: NAleksandar Radovanovic <biblbroks@sezampro.yu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>,
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There is a problem in some hardware where the kernel will stall for
35 seconds waiting for disks that don't exist. This patch will skip
waiting for the BSY-bit on IDE drives to go away if you set "hdx=noprobe"
as a kernel option and the disk is not marked as 'present' (like when
you set the geometry by hand).

If no noprobe-option is set the code will work (more or less) as the
original but if set the code will skip the ide_wait_not_busy() for
that drive. Even if there would be a drive there and it is still busy
afterwards it should not matter since it isn't probed for later.

The code also honors the MAX_DRIVES variable instead of assuming that
there will be two harddrives on the bus.

Bart: minor cleanups
Signed-off-by: NJonas Stare <jonas.stare@purplescout.se>
CC: Andrew Morton <akpm@linux-foundation.org>,
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The intent behind siimage_reset() was probably to hard reset the interface and
the SATA PHY but as the code writes to two reserved bits instead, it obviously
has been ineffective from the start. So, just remove it.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix handling of the PIO modes for the pre-EIDE drives that did not support
the PIO Flow Control Transfer Mode value (00001 nnn) of the Set Transfer Mode
feature by skipping the actual mode programming.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

With newer kernels HDD in my old laptop is limited to UDMA 33.
With this patch I get UDMA 100 again.
Signed-off-by: NGabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Plip passes a string "name" that is allocated on stack to
parport_register_device.  parport_register_device holds the pointer to
"name" and when the registering function exits, it points nowhere.

On some machine, this bug causes bad names to appear in /proc, such as
/proc/sys/dev/parport/parport0/devices/T^/�X^/�, on others, the plip
proc node is completely missing.

The patch also fixes documentation to note this requirement.
Signed-off-by: NMikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

netif_rx is meant to be called from interrupts because it doesn't wake
up ksoftirqd.  For calling from outside interrupts, netif_rx_ni exists.

This fixes plip to use netif_rx_ni.  It fixes the infamous error "NOHZ:
local_softirq_panding 08" that happens on some machines with NOHZ and
plip --- it is caused by the fact that softirq is pending and ksoftirqd
is sleeping.
Signed-off-by: NMikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

... which I've found on a Sapphire X550 (Silent).
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndreas Herrmann <aherrman@arcor.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Amiga zorro bus: Add missing zorro_device_remove(). Without this ifconfig and
/proc/net/dev oops after unloading a Zorro network device driver module.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=9416Signed-off-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

if you are lucky (unlucky?) enough to have shared interrupts, the
interrupt handler can be called before the tasklet and lock are ready
for use.
Signed-off-by: Nchas williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

AMD Opteron processors before CG revision don't like C-states > 1.

This solves the long standing bugzilla #5303 and probably some more
on affected machines:

  http://bugzilla.kernel.org/show_bug.cgi?id=5303

[ tglx@linutronix.de: reworked the patch so it does not wreck ia64 ]
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

None of the drives I have follows what the standard says about
transfer chunk size.  Of the four SATA and six PATA ATAPI devices
tested, four ignore transfer chunk size completely and the ones which
honor it don't behave according to the spec when it's odd.

According to the spec, transfer chunk size can be odd if the amount of
data to transfer equals or is smaller than the chunk size and the
device can indicate the same odd number and transfer the whole thing
at one go with a pad byte appended.  However, in reality, none of the
drives I have does that.  They all indicate and transfer even number
of bytes one byte shorter than the chunk size first; then indicate and
transfer two bytes, which is clearly out of spec.

In addition to unnecessary second PIO data phase, this also creates a
weird problem when combined with SATA controllers which perform PIO
via DMA.  Some of these controllers use actualy number of bytes
received to update DMA pointer so chunks which are sized 4n + 2 makes
DMA pointer off by two bytes.  This causes data corruption and buffer
overruns.

This patch rounds nbytes up to the nearest even number such that ATAPI
devices don't split data transfer for the last odd byte.  This
shouldn't confuse controllers which depend on transfer chunk size as
devices will report the rounded-up number, actually transfer that much
and padding buffer is there to receive them.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

INT status can be OR.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

If a card has no IRQ then pass no interrupt handler but allow polled
usage.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Hopefully there is a better long term solution but for now lets favour
reliability.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

And next time I'll be able to find the ata tape spec easily...
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Should use ioread* as discussed previously
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

sil24 unnecessarily used LIBATA_MAX_PRD and ATAPI sg table was short
by one entry which might cause very obscure problems.  This patch
updates sg table sizing such that

* One full page is used for PRB + sg table.  On 4k page,
  this results in 253 sg's.

* Make ATAPI sg block properly sized.

* Make build fail if command block size doesn't equal PAGE_SIZE.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There are two bugs in disabled port handling.

* test in PORT_PATA0 is reversed
* ->prereset should return -ENOENT for disabled ports not 0

The first bug makes the PATA channel considered disabled but the
second bug saves the day by returning 0.  The net result is that cable
is always left at ATA_CBL_UNKNOWN.  This results in false 80c
configuration and thus transfer errors.

This patch fixes both bugs.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Since writing to two reserved bits ain't much of a housekeeping, I think it's
time we get rid of the custom error handler in this driver. ;-)
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Move the code which marks the minor number as free to mmc_blk_put() so
that it happens on the final close() (or removal), instead of doing it
at removal even when the device is still logically open.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

It is possible to handle arbitrary block sizes with tifm card reader by
conditionally switching to PIO in case such block has to be delivered. At
the beginning of each request, DMA is either disabled (non-power-of-2 block
size) or set to load time user preference.
Signed-off-by: NAlex Dubov <oakad@yahoo.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Some cards have been reported to signal that they're ready prematurely.
Checking both the busy bit and card state solves the issue.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Some controllers fail to send confirmation GPE after address or data write.
Detect this and don't expect such confirmation in future.
This is a generalization of previous workaround
(66c5f4e7), which did only read address.

Reference: http://bugzilla.kernel.org/show_bug.cgi?id=9327Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: NRomano Giannetti <romano.giannetti@gmail.com>
Tested-by: Mats Johannesson
Signed-off-by: NLen Brown <len.brown@intel.com>

Sometimes it is usefull to see raw protocol dump.
Uncomment '#define DEBUG' at the beginning of file to make EC
really verbose.
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

This reverts commit f2d68935.

Make sure all subchannel handling is done on the slow path workqueue
so that we don't have races between an old subchannel unregistering
and a new subchannel with the same name registering.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Modify the sense id channel program to allow device sensing of pav
alias devices which belong to a base device with ungrouped paths.
Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Use mp_irqs[] to get PNP device's interrupt polarity and trigger.
There are two reasons to do this:
1. BIOS bug for PNP interrupt
2. BIOS explictly does override
mp_irqs[] should cover all the cases.

http://bugzilla.kernel.org/show_bug.cgi?id=5243
http://bugzilla.kernel.org/show_bug.cgi?id=7679
http://bugzilla.kernel.org/show_bug.cgi?id=9153

[lenb: fixed !IOAPIC and 64-bit !SMP builds]
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fix for http://bugzilla.kernel.org/show_bug.cgi?id=9355

cpuidle always used to fallback to C2 if there is some bm activity while
entering C3. But, presence of C2 is not always guaranteed. Change cpuidle
algorithm to detect a safe_state to fallback in case of bm_activity and
use that state instead of C2.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Port 2aa44d05
(sched: sched_clock_idle_[sleep|wakeup]_event()) to cpuidle.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Port 18eab855
(Enable C3 even when PM2_control is zero) to cpuidle.

Without this patch, some systems will notice a regression
when enabling CPU_IDLE -- C3 would no longer be available.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

set_ibm_param() could OOPS with a NULL pointer derreference if one did not give
any values for a module parameter it handles.  This would, of course, cause all
sort of trouble for future modprobing and require a reboot to clean up
properly.

Fix it by returning -EINVAL if no values are given for the parameter, and also
avoid any nastyness from BUG_ON while at it.

How to reproduce: modprobe thinkpad-acpi brightness
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Tested-by: NMike Kershaw <dragorn@kismetwireless.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

This reverts commit 9cd8047b.

Option to init EC early inserted to handle #8598 ASUS problem,
introduced several others.

EC driver in this particular case has fake _INI method, not present on
other machines, which don't need or break from this workaround, so lets use
its presence as a flag for early init.

http://bugzilla.kernel.org/show_bug.cgi?id=9262
http://bugzilla.kernel.org/show_bug.cgi?id=8598
https://bugzilla.novell.com/show_bug.cgi?id=334806Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>