Table 6-2: CCCR bit Definitions, address 00h.  Part E1 SDIO Simplified
Specification Version 3.00, Feb. 25, 2011.

This patch has been tested with Marvell WLAN device SD8797.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

HPI command is defined in eMMC4.41.
This feature is important for eMMC4.5 devices.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds cache feature of eMMC4.5 Spec.
If device supports cache capability, host can utilize some specific
operations.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

MMC v4.5 supports the DISCARD feature (CMD38).  It's different from
trim and there's no check bit.  Currently it's only supported at v4.5.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In the v4.5, there's no secure erase & trim support.
Instead it supports the sanitize feature.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In dw_mmc 2.40a spec, Data register's offset is changed.
Before we used Data register offset 0x100. but if somebody uses a
2.40a controller, we must use 0x200 for Data register.

This patch adds a version-id checking point and uses SDMMC_DATA(x)
instead of SDMMC_DATA.  It assumes 2.40a is the latest version.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds support for the power off notify feature, available in
eMMC 4.5 devices. If the host has support for this feature, then the
mmc core will notify the device by setting the POWER_OFF_NOTIFICATION
byte in the extended csd register with a value of 1 (POWER_ON).

For suspend mode short timeout is used, whereas for the normal poweroff
long timeout is used.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

EXT_CSD[248] includes the default maximum timeout for CMD6.
This field is added at eMMC4.5 Spec. And it can be used for default
timeout except for some operations which don't define the timeout
(i.e. background operation, sanitize, flush cache) in eMMC4.5 Spec.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Ths patch allows runtime PM for sdhci-pci, runtime suspending after
inactivity of 50ms and ensuring runtime resume before SDHC registers
are accessed.  During runtime suspend, interrupts are masked.
The host controller state is restored at runtime resume.

For Medfield, the host controller's card detect mechanism is
supplanted by an always-on GPIO which provides for card detect wake-up.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

It allows gerneral purpose partitions in MMC Device.  And I try to simply
make mmc_blk_alloc_parts using mmc_part structure suggested by Andrei
Warkentin.  After patching, we see general purpose partitions like this:
> cat /proc/partitions
          179 0 847872 mmcblk0
          179 192 4096 mmcblk0gp3
          179 160 4096 mmcblk0gp2
          179 128 4096 mmcblk0gp1
          179 96  1052672 mmcblk0gp0
          179 64  1024 mmcblk0boot1
          179 32  1024 mmcblk0boot0
Signed-off-by: NNamjae Jeon <linkinjeon@gmail.com>
Acked-by: NAndrei Warkentin <awarkentin@vmware.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Intel Medfield platform blocks access to eMMC boot partitions which
results in switch errors.  Since there is no access, mmcboot0/1
devices should not be created.  Add a host capability to reflect that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds the power class selection feature available for mmc
versions 4.0 and above.  During the enumeration stage before switching
to the lower data bus, check if the power class is supported for the
current bus width. If the power class is available then switch to the
power class and use the higher data bus. If power class is not supported
then switch to the lower data bus in a worst case.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Provide platforms with a simplified way to specify MMCIF DMA slave IDs in
a way, similar to SDHI and other sh_dma clients.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

eMMC's may have a hardware reset line.  This patch provides a
host controller operation to implement hardware reset and
a function to reset and reinitialize the card.  Also, for MMC,
the reset is always performed before initialization.

The host must set the new host capability MMC_CAP_HW_RESET
to enable hardware reset.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The err condition in post_req() is set to undo a call made to pre_req()
that hasn't been started yet.  The err condition is not set if an MMC
request returns an error.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Adds a quirk which can be turned on for SDIO devices that do not support
512 byte requests in byte mode during CMD53. These requests will always
be sent in block mode instead.

This patch also enables this quirk for ST-Ericsson CW1200 WLAN device.
Signed-off-by: NStefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: NUlf HANSSON <ulf.hansson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Allow named IRQs to use corresponding specific handlers. If named IRQs are
used, at least an "sdcard" IRQ has to be specified by the platform. If
names are not used, an arbitrary number of IRQs can be provided by the
platform, in which case the generic ISR will be used for each of them.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NMagnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
[g.liakhovetski@gmx.de: style and typo corrections, platform data check]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This adds support to inject data errors after a completed host transfer.
The mmc core will return error even though the host transfer is successful.
This simple fault injection proved to be very useful to test the
non-blocking error handling in the mmc_blk_issue_rw_rq().
Random faults can also test how the host driver handles pre_req()
and post_req() in case of errors.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Acked-by: NAkinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

"mmc: dw_mmc: Fix DDR mode support" removed the last user.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Non default Drive Strength cannot be set automatically.  It is a function
of the board design and only if there is a specific platform handler can
it be set.  The platform handler needs to take into account the board
design.  Pass to the platform code the necessary information.

For example:  The card and host controller may indicate they support HIGH
and LOW drive strength.  There is no way to know what should be chosen
without specific board knowledge.  Setting HIGH may lead to reflections
and setting LOW may not suffice.  There is no mechanism (like ethernet
duplex or speed pulses) to determine what should be done automatically.

If no platform handler is defined -- use the default value.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Reviewed-by: NArindam Nath <arindam.nath@amd.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Previously there has only been one function mmc_wait_for_req()
to start and wait for a request. This patch adds:

 * mmc_start_req() - starts a request wihtout waiting
   If there is on ongoing request wait for completion
   of that request and start the new one and return.
   Does not wait for the new command to complete.

This patch also adds new function members in struct mmc_host_ops
only called from core.c:

 * pre_req - asks the host driver to prepare for the next job
 * post_req - asks the host driver to clean up after a completed job

The intention is to use pre_req() and post_req() to do cache maintenance
while a request is active. pre_req() can be called while a request is
active to minimize latency to start next job. post_req() can be used after
the next job is started to clean up the request. This will minimize the
host driver request end latency. post_req() is typically used before
ending the block request and handing over the buffer to the block layer.

Add a host-private member in mmc_data to be used by pre_req to mark the
data. The host driver will then check this mark to see if the data is
prepared or not.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NVenkatraman S <svenkatr@ti.com>
Tested-by: NSourav Poddar <sourav.poddar@ti.com>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

There are several situations when dw_mci_submit_data_dma() decides to
fall back to PIO mode instead of using DMA, due to a short (to avoid
overhead) or "complex" (e.g. with unaligned buffers) transaction, even
though host->use_dma is set. However dw_mci_stop_dma() decides whether
to stop DMA or set the EVENT_XFER_COMPLETE event based on host->use_dma.
When falling back to PIO mode this results in data timeout errors
getting missed and the driver locking up.

Therefore add host->using_dma to indicate whether the current
transaction is using dma or not, and adjust dw_mci_stop_dma() to use
that instead.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some host controllers will not operate without a hardware
timeout that is limited in value.  However large discards
require large timeouts, so there needs to be a way to
specify the maximum discard size.

A host controller driver may now specify the maximum discard
timeout possible so that max_discard_sectors can be calculated.

However, for eMMC when the High Capacity Erase Group Size
is not in use, the timeout calculation depends on clock
rate which may change.  For that case Preferred Erase Size
is used instead.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Update functions for PIO pushing and pulling data to and from the FIFO
so that they can handle unaligned output buffers and unaligned buffer
lengths. This makes more of the tests in mmc_test pass.

Unaligned lengths in pulls are handled by reading the full FIFO item,
and storing the remaining bytes in a small internal buffer (part_buf).
The next data pull will copy data out of this buffer first before
accessing the FIFO again. Similarly, for pushes the final bytes that
don't fill a FIFO item are stored in the part_buf (or sent anyway if
it's the last transfer), and then the part_buf is included at the
beginning of the next buffer pushed.

Unaligned buffers in pulls are handled specially if the architecture
cannot do efficient unaligned accesses, by reading FIFO items into a
aligned local buffer, and memcpy'ing them into the output buffer, again
storing any remaining bytes in the internal buffer. Similarly for pushes
the buffer is memcpy'd into an aligned local buffer then written to the
FIFO.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The FIFO_DEPTH hardware configuration parameter can be found from the
power-on value of RX_WMark in the FIFOTH register. This is used to
initialise the watermarks, but when calculating the number of free fifo
spaces a preprocessor definition is used which is hard coded to 32.

Fix reading the value out of FIFOTH (the default value in the RX_WMark
field is FIFO_DEPTH-1 not FIFO_DEPTH). Allow the fifo depth to be
overriden by platform data (since a bootloader may have changed FIFOTH
making auto-detection unreliable). Store the fifo_depth for later use.
Also fix the calculation to find the number of free bytes in the fifo to
include the fifo depth in the left shift by the data shift, since the
fifo depth is measured in fifo items not bytes.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Convert the card insert/remove tasklet to a workqueue, and call the
setpower platform specific callback without the spinlock held. This
means neither of the setpower or get_cd callbacks are called from atomic
context which allows them to sleep.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some controllers require waiting for the bus to become idle
before writing to some registers. I have implemented this
by adding a hook to sd_ctrl_write16() and implementing
a hook for SDHI which waits for the bus to become idle.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NChris Ball <cjb@laptop.org>

This reflects at least the current usage of this register
and I think it improves the readability of the code ever so slightly.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NChris Ball <cjb@laptop.org>

If the MMC_SEND_STATUS command is not successful, we should not return
a zero status word, but instead allow the caller to know positively
that an error occurred.

Convert the open-coded get_card_status() to use the helper function,
and provide definitions for the card state field.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Standardize the checks for multiple MMC header file inclusion,
including adding comments to terminating #endif's, and fixing
one incorrect comment.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NChris Ball <cjb@laptop.org>

The structure sdhci_pltfm_data is not necessarily to be in a public
header like include/linux/mmc/sdhci-pltfm.h, so the patch moves it
into drivers/mmc/host/sdhci-pltfm.h and eliminates the former one.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Reviewed-by: NGrant Likely <grant.likely@secretlab.ca>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The patch turns the common stuff in sdhci-pltfm.c into functions, and
add device drivers their own .probe and .remove which in turn call
into the common functions, so that those sdhci-pltfm device drivers
register itself and keep all device specific things away from common
sdhci-pltfm file.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Reviewed-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

On reading the ext_csd for the first time (in 1 bit mode), save the
ext_csd information needed for bus width compare.

On every pass we make re-reading the ext_csd, compare the data
against the saved ext_csd data.

This fixes a regression introduced in 3.0-rc1 by 08ee80cc
("mmc: core: eMMC bus width may not work on all platforms"), which
incorrectly assumed we would be re-reading the ext_csd at resume-
time.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Enables Auto-CMD23 support where available (SDHCI 3.0 controllers)
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Tested-by: NArindam Nath <arindam.nath@amd.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

SD cards operating at UHS104 or better support SET_BLOCK_COUNT.
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Reviewed-by: NArindam Nath <arindam.nath@amd.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Implements support for multiblock transfers bounded
by SET_BLOCK_COUNT (CMD23).
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

CMD23-prefixed instead of open-ended multiblock transfers
have a performance advantage on some MMC cards.
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Conditional add/remove quirks for MMC and SD.
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

eMMC voltage change not required for 1.8V.  3.3V and 1.8V vcc
are capable of doing DDR. vccq of 1.8v is not required.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Reviewed-by: NArindam Nath <arindam.nath@amd.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Supply a link to TMIO private data for platforms to implement their
own card detection.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>