Add missing sysconfig/sysstatus information
to OMAP3 hwmod. The information has been
checked against OMAP34xx and OMAP36xx TRM.

Without this change DSI block is not reset
during boot, which is required for working
Nokia N950 display.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

If the module has no clkctrl register defined, module_wait_ready should
not try to access this. This can potentially cause an illegal register
access, and result in bad idle reporting also.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The previous implementation was racy in many locations, where the current
status of the clockdomain was read out, some operations were executed,
and the previous status info was used afterwards to decide next state
for the clockdomain. Instead, fix the implementation of the allow_idle /
deny_idle APIs to properly have usecounting support. This allows clean
handling internally within the clockdomain core, and simplifies the
usage also within hwmod.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With the introduction of hwmod module clocks, the name of the hwmod
main clk may not be available before hwmod setup, as hwmod setup
may lookup the main clock dynamically based on the hwmod name.
Thus, change the order of hwmod setup and main clock handling for
the timer code, to make sure the main clock is going to be
available.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With the transition to hwmod module clocks, all hwmods will have
their main clocks named <hwmod_name>_mod_ck. Use this info to
fetch main_clk, and use it if found.

Also, if a main_clk is found based on the hwmod name, disable
the direct PRCM modulemode access from hwmod.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This avoids the need to add most of the clock aliases under
drivers/clk/ti/clk-xyz.c files.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

I found one more make randconfig build error with the recent
SMP kexec changes. We need the mpuss now always available early.

Fixes: 0573b957 ("ARM: OMAP4+: Prevent CPU1 related hang
with kexec")
Signed-off-by: NTony Lindgren <tony@atomide.com>

Looks like I only partially fixed up things if CONFIG_SMP
is not set for the recent kexec changes. We don't have
boot_secondary available without SMP as reported by Arnd.

Fixes: 0573b957 ("ARM: OMAP4+: Prevent CPU1 related hang with kexec")
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Kexec needs omap4_cpu_kill, otherwise kexec will produce on SMP:

kexec_load failed: Invalid argument
Acked-by: NSantosh Shilimkar <ssantosh@kernel.org>
Tested-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

We need to reset CPU1 properly for kexec when booting different
kernel versions. Otherwise CPU1 will attempt to boot the the
previous kernel's start_secondary(). Note that the restctrl
register is different from the low-power mode wakeup register
CPU1_WAKEUP_NS_PA_ADDR. We need to configure both.

Let's fix the issue by defining SoC specific data to initialize
things in a more generic way. And let's also standardize omap-smp.c
to use soc_is instead of cpu_is while at it.
Acked-by: NSantosh Shilimkar <ssantosh@kernel.org>
Tested-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Kexec booted kernels on omap4 will hang early during the boot if the
booted kernel is different version from the previous kernel.

This is because the previous kernel may have configured low-power mode
using CPU1_WAKEUP_NS_PA_ADDR. In that case it points to the previous
kernel's omap4_secondary_startup(), and CPU1 can be in low power mode
from the previous kernel. When the new kernel configures the CPU1
clockdomain, CPU1 can wake from low power state prematurely during
omap44xx_clockdomains_init() running random code.

Let's fix the issue by configuring CPU1_WAKEUP_NS_PA_ADDR before we
call omap44xx_clockdomains_init(). Note that this is very early during
the init, and we will do proper CPU1 reset during SMP init a bit later
on in omap4_smp_prepare_cpus(). And we need to do this when SMP is
not enabled as the previous kernel may have had it enabled.
Acked-by: NSantosh Shilimkar <ssantosh@kernel.org>
Tested-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Prepare things for making kexec work on SMP omap variants by initializing
SARM RAM base early. This allows us to configure CPU1 for kexec in case
the previous kernel has put CPU1 in low power mode.

Note that this should not prevent moving other SAR RAM code to live
under drivers. However for kexec, we will need this very early.
Acked-by: NSantosh Shilimkar <ssantosh@kernel.org>
Tested-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As per the TRM: http://www.ti.com/lit/ug/spruh73m/spruh73m.pdf
offset 0x4 is reserved for PRM_PER. Hence removing the wrongly
defined address offset.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The ti81xx_rtc_hwmod is not exported, or declared outside the file
arch/arm/mach-omap2/omap_hwmod_81xx_data.c so make it static to
avoid the following warning:

arch/arm/mach-omap2/omap_hwmod_81xx_data.c:246:19: warning: symbol 'ti81xx_rtc_hwmod' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

pruss hwmod RSTST register wrongly points to PWRSTCTRL register in case of
am43xx. Fix the RSTST register offset value.

This can lead to setting of wrong power state values for PER domain.

Fixes: 1c7e224d ("ARM: OMAP2+: hwmod: AM335x: runtime register update")
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The addresses for DSS are provided in the DT data, so they can be
removed from the hwmod.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

QSPI address space information is passed from device tree. Therefore
remove legacy way of passing address space via hwmod data.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The new pdata callback (force_ick_on) is now used by the driver and the old
callback related code can be removed.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The McBSP sidetone (in OMAP3 McBSP2 and 3 module) is working with the
module's interface clock. When the sidetone is enabled the iclk must not
idle because it will result in choppy sidetone.
Switch to use the new callback for handling the iclk allow/deny idle
configuration.
For this the driver needs to get the module's ick clock and pass the clk
pointer to the callback.
In DT boot, the pdata-quirk is going to set up the callback for the driver
so save it if it is set in the pdata of the device.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The function will do more then removing the sysfs files in the future.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

McBSP2/3 module's sidetone module operates using the module's ICLK clock.
When the Sidetone is in use the interface clock of the module must not
idle. To prevent the iclk idling the driver expects to have pdata callback
to call. With this patch the callback is going to be set up for DT boot
also.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

McBSP2/3 module's sidetone module operates using the module's ICLK clock.
When the Sidetone is in use the interface clock of the module must not
idle. The new callback expects to receive the *clk of the module's ick and
not the id number of the McBSP. This will allow us more cleanups and going
to simplify the ICLK handling.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The McBSPLP's sidetone main clock is the McBSPLP's ICLK, not FCLK as the
sidetone only receives the ICLK from the main McBSP module.
Since the McBSP and sidetone is using the very same clock from PRCM level
the sidetone must not have the prcm section to check the clock status since
the sidetone is only used when McBSP is already configured.
If two separate hwmods looking at the same bit and they would use
pm_runtime in nested way (as it must happen with McBSP and it's ST module)
the hwmod would warn, because the idlest will not match what it is expected
after enable/disable of the clocks.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Devices that utilize the OCP registers and/or PRCM registers and
register bit fields should be modeled using hwmod. Since eQEP, ePWM and
eCAP don't fall under this category, remove their hwmod entries.

Instead these clocks simply use the clock that is passed through by its
parent PWMSS. Therefore, PWMSS handles the clock for itself and its
subdevices.
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NAndrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NAndrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NAndrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NAndrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NAndrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NAndrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NAndrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add tblck to the pwm nodes. This insures that the ehrpwm driver has access
to the time-based clk.

Do not remove similar entries for ehrpwm node. Later patches will switch
from using ehrpwm node name to pwm. But to maintain ABI compatibility we
shouldn't remove the old entries.
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Merge branch 'peter/for-4.8_omapdss_part1' of https://github.com/omap-audio/linux-audio into omap-for-v4.8/soc

Instead of the full omapdss internal header, include only the platform_data
header.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Create a new header file for platform data used by omapdss.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>

The omap_display_init() is implemented in the mach-omap2/display.c so the
declaration should have been there as well.
Change the board files to include display.h to avoid build breakage at the
same time.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

OMAP_DSS_VENC_TYPE_COMPOSITE is 0. There is no need to explicitly set the
connector_type.
This change is needed for the omapdss header cleanup.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

The self-test was updated to cover zero-length strings; the function
needs to be updated, too.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NGeorge Spelvin <linux@sciencehorizons.net>
Fixes: fcfd2fbf ("fs/namei.c: Add hashlen_string() function")
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>