This patch adds some macros instead of fixed value for AMDTP according to
IEC 61883-1/6. These macros will also be used by followed patches.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch renames some functions, a structure and its member to reuse them
in both AMDTP in/out stream.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The if condition here was supposed to return on error but the return
statement is missing.  The effect is that the ->mixername is set to
"???" instead of "DT019X".
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The register CLASS_D_CONTROL_1 is marked as volatile because it contains
a bit, DAC_MUTE, which is also mirrored in the ADC_DAC_CONTROL_1
register. This causes problems for the "Speaker Switch" control, which
will report an error if the CODEC is suspended because it relies on a
volatile register.

To resolve this issue mark CLASS_D_CONTROL_1 as non-volatile and
manually keep the register cache in sync by updating both bits when
changing the mute status.
Reported-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

Commit 10df3509 ("ASoC: Intel: Fix Audio DSP usage when IOMMU is
enabled.") caused following regression in Baytrail SST:

baytrail-pcm-audio baytrail-pcm-audio: error: DMA alloc failed
baytrail-pcm-audio baytrail-pcm-audio: error: failed to load firmware

Fix this by calling dma_coerce_mask_and_coherent() in sst_byt_init() with
the same dma_dev device what is now used in sst_fw_new() when allocating the
DMA buffer.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Broadwell display controller has 3 stream DMA engines. DMA0 cannot update DMA
postion buffer properly while DMA1 and DMA2 can work well. So this patch masks
the buggy DMA0 by keeping it as opened.

This is a tentative workaround, so keep the change small as Takashi suggested.
Signed-off-by: NMengdong Lin <mengdong.lin@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Vendor ID 0x10de0071 is used by a yet-to-be-named GPU chip.
Signed-off-by: NAaron Plattner <aplattner@nvidia.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

According to Reference Manual -- ESAI Initialization chapter, as the
standard procedure of ESAI personal reset, the PCRC and PRRC registers
should be remained in its reset value and then configured after T/RCCR
and T/RCR configurations's done but before TE/RE's enabling.

So this patch moves PCRC and PRRC settings to the end of hw_params().
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

ESAI can only output EXTAL clock source directly. But for FSYS clock source,
ESAI can not output it without getting through PSR PM dividers.

So this patch adds an extra check in the code.
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The range here from 1 to 16 is confined to FP divider only while the
sck_div indicates if the calculation contains PSR and PM dividers. So
for the case using PSR and PM since the sck_div is true, the range of
ratio would simply become bigger than 16.

So this patch fixes the condition here and adds one line comments to
make the purpose here clear.
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Currently when the DAPM context bias level is SUSPEND and the target bias level
is OFF dapm_pre_sequence_async() will first transition to PREPARE and
dapm_post_sequence_async() will then transition back from PREPARE to STANDBY and
then to OFF.

This patch makes sure that dapm_pre_sequence_async() only transitions to PREPARE
when either going to ON or away from ON. This avoids the extra unnecessary
transitions.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

For CODEC to CODEC DAI links the paths are created in snd_soc_dapm_new_pcm().
Also for CODEC to CODEC links the widgets are connected cross-over via a DAI
link widget, meaning that the capture widget of one CODEC will be connected to
the playback widget of the other and vice versa. Whereas
snd_soc_dapm_connect_dai_link_widgets() directly connects the playback widget of
the CPU DAI to the playback widget of the CODEC DAI and the capture widget of
the CPU DAI to the capture widget of the CODEC DAI. So not skipping
CODEC<->CODEC links in snd_soc_dapm_connect_dai_link_widgets() will create
incorrect connections between the two CODECs which will cause DAPM to detect
active paths where there are none and unnecessarily power up widgets.

Fixes: b893ea5f ("ASoC: sapm: Automatically connect DAI link widgets in DAPM graph.")
Cc: <stable@vger.kernel.org> (for 3.14+)
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The regular state before we execute SNDRV_PCM_TRIGGER_SUSPEND should be
SNDRV_PCM_TRIGGER_START, not SNDRV_PCM_TRIGGER_STOP. Thus fix it.
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

When we plug a 3-ring headset on the Dell machines (VID: 0x10ec0255,
SID: 0x1028065c; VID: 0x10ec0255, SID: 0x10280680; VID: 0x10ec0292,
SID: 0x10280684), the headset mic can't be detected, after apply this
patch, the headset mic can work well.

And on the machine with SID 0x10280684, and the Lineout and external
microphone should be routed to docking, this patch also fix this
problem.

BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: NHui Wang <hui.wang@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Block offset calculations are done in the contiguous allocator so
are not required here.
Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch fixes the following dereference check ordering.

 sound/soc/intel/sst-haswell-pcm.c:749 hsw_pcm_probe() warn: variable dereferenced before check 'pdata' (see line 746)

 git remote add asoc git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
 git remote update asoc
 git checkout 0b708c87
 vim +/pdata +749 sound/soc/intel/sst-haswell-pcm.c

 a4b12990 Mark Brown    2014-03-12  740  };
 a4b12990 Mark Brown    2014-03-12  741
 a4b12990 Mark Brown    2014-03-12  742  static int hsw_pcm_probe(struct snd_soc_platform *platform)
 a4b12990 Mark Brown    2014-03-12  743  {
 a4b12990 Mark Brown    2014-03-12  744  	struct sst_pdata *pdata = dev_get_platdata(platform->dev);
 a4b12990 Mark Brown    2014-03-12  745  	struct hsw_priv_data *priv_data;
 0b708c87 Liam Girdwood 2014-05-02 @746  	struct device *dma_dev = pdata->dma_dev;
 0b708c87 Liam Girdwood 2014-05-02  747  	int i, ret = 0;
 a4b12990 Mark Brown    2014-03-12  748
 a4b12990 Mark Brown    2014-03-12 @749  	if (!pdata)
 a4b12990 Mark Brown    2014-03-12  750  		return -ENODEV;
 a4b12990 Mark Brown    2014-03-12  751
 a4b12990 Mark Brown    2014-03-12  752  	priv_data = devm_kzalloc(platform->dev, sizeof(*priv_data), GFP_KERNEL);
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Since commit 1df5a06a ("ALSA: hda - hdmi: Fix programmed active channel
count") channel count is no longer being set if monitor_present is 0.
This is because setting the count was moved after the CA value is
determined, which is only after the monitor_present check in
hdmi_setup_audio_infoframe().

Unfortunately, in some cases, such as with a non-spec-compliant codec or
with a problematic video driver, monitor_present is always 0. As a
specific example, this seems to happen with gen1 ATV (SiI1390 codec),
causing left-channel-only stereo playback (multi-channel playback has
apparently never worked with this codec despite it reporting 8 channels,
reason unknown).

Simply setting converter channel count without setting the pin infoframe
and channel mapping as well does not theoretically make much sense as
this will just mean they are out-of-sync and multichannel playback will
have a wrong channel mapping.

However, adding back just setting the converter channel count even in
no-monitor case is the safest change which at least fixes the stereo
playback regression on SiI1390 codec. Do that.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Reported-by: NStephan Raue <stephan@openelec.tv>
Tested-by: NStephan Raue <stephan@openelec.tv>
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Read the stream offset and presentation position from DSP memory rather
than using the old estimated position. This fixes timing issues with
pulseaudio.
Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

hw_params() can be called multiple times. Make sure we release the DSP
stream that was allocated on previous hw_params() calls before allocating
a new DSP stream.
Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The Intel IOMMU requires that the ACPI device is used to allocate all
DMA memory buffers. This means we need to pass the DMA device pointer into child
component devices that allocate DMA memory.

We also only set the DMA mask for the ACPI device now instead of for each
component device.
Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Fix page table creation on Haswell and Broadwell to remove unsafe
virt_to_phys mappings and use more portable SG buffer. Use audio buffer
APIs to allocate DMA buffers.
Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Make sure we add the allocated blocks to the modules list of blocks.
Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Make sure we dont alloc blocks twice with requests spanning more
than one block.
Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The TEAC UD-H01 firmware sends wrong feedback frequency values, thus
causing the PC to send the samples at a wrong rate, which results in
clicks and crackles in the output.

Add a workaround to detect and fix the corruption.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
[mick37@gmx.de: use sender->udh01_fb_quirk rather than
 ep->udh01_fb_quirk in snd_usb_handle_sync_urb()]
Reported-and-tested-by: NMick <mick37@gmx.de>
Reported-and-tested-by: NAndrea Messa <andr.messa@tiscali.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The recent addition of the USB audio mixer suspend/resume may lead to
deadlocks when the driver tries to call usb_autopm_get_interface()
recursively, since the function tries to sync with the finish of the
other calls.  For avoiding it, introduce a flag indicating the resume
operation and avoids the recursive usb_autopm_get_interface() calls
during the resume.
Reported-and-tested-by: NBryan Quigley <gquigs@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The suspend callback of usb-audio driver may be called multiple times
per suspend when multiple USB interfaces are bound to a single sound
card instance.  In such a case, it's superfluous to save the mixer
values multiple times.  This patch fixes it by checking the counter.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This (widely used) construction:

if(printk_ratelimit())
	dev_dbg()

Causes the ratelimiting to spam the kernel log with the "callbacks suppressed"
message below, even while the dev_dbg it is supposed to rate limit wouldn't
print anything because DEBUG is not defined for this device.

[  533.803964] retire_playback_urb: 852 callbacks suppressed
[  538.807930] retire_playback_urb: 852 callbacks suppressed
[  543.811897] retire_playback_urb: 852 callbacks suppressed
[  548.815745] retire_playback_urb: 852 callbacks suppressed
[  553.819826] retire_playback_urb: 852 callbacks suppressed

So use dev_dbg_ratelimited() instead of this construction.
Signed-off-by: NSander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When we plug a 3-ring headset on the Dell machine (VID: 0x10ec0255,
SID: 0x1028067e), the headset mic can't be detected, after apply this
patch, the headset mic can work well.

BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: NHui Wang <hui.wang@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The recent commit (ca460f86) changed the CORB RP reset procedure to
follow the specification with a couple of sanity checks.
Unfortunately, Nvidia controller chips seem not following this way,
and spew the warning messages like:
  snd_hda_intel 0000:00:10.1: CORB reset timeout#1, CORBRP = 0

This patch adds the workaround for such chips.  It just skips the new
reset procedure for the known broken chips.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When we plug a 3-ring headset on the Dell machine (VID: 0x10ec0255,
SID: 0x10280674), the headset mic can't be detected, after apply this
patch, the headset mic can work well.

BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: NHui Wang <hui.wang@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use a newline character appropriately.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

I suppose there is a possibility that hsw_notification_work() may run after
sst_hsw_stream_free() which can lead to a kernel crash since struct
sst_hsw_stream is freed at that point and
stream = container_of(work, struct sst_hsw_stream, notify_work) is not valid
when hsw_notification_work() is run.
Reported-by: NDerek Basehore <dbasehore@chromium.org>
Reported-by: NWenkai Du <wenkai.du@intel.com>
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

audmux_debugfs_init() is marked as __init, but is called from imx_audmux_probe()
which is not marked as __init. This creates a section mismatch and a potential
runtime crash (if imx_audmux_probe() is called after the .init section was
dropped). This patch removes the __init annotation from audmux_debugfs_init(),
which fixes the following warning:
	WARNING: sound/soc/built-in.o(.text+0x86960): Section mismatch in reference
	from the function imx_audmux_probe() to the function
	.init.text:audmux_debugfs_init()
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

rsnd_soc_dai_trigger() will be called
after rsnd_dai_pointer_update() function
which is using rsnd_lock().
Thus, it should be called from outside of rsnd_lock().
Kernel will be hangup without this patch.
Special thanks to Kataoka-san
Reported-by: NRyo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

There is a race between sst_byt_stream_free() and sst_byt_get_stream()
if sst_byt_get_stream() called from sst_byt_irq_thread() context is
accessing the byt->stream_list while a stream is deleted from the list.

A stream is added to byt->stream_list in sst_byt_stream_new() and deleted in
sst_byt_stream_free(). sst_byt_get_stream() is always protected by
sst->spinlock, but the stream addition and deletion are not protected.

The patch adds spinlock to both stream addition and deletion.

[Jarkko: Same fix added to sst-haswell-ipc.c too]
Signed-off-by: NWenkai Du <wenkai.du@intel.com>
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Commit 0406a40a ("ASoC: jz4740: Use the generic dmaengine PCM driver")
jz4740-pcm.c file, but neglected to remove the Makefile entries.

Fixes: 0406a40a ("ASoC: jz4740: Use the generic dmaengine PCM driver")
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Reported-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

There were occasional ADSP crash during reboot testing:

[   11.883364] BUG: unable to handle kernel paging request at ffffc90121700000
[   11.883380] IP: [<ffffffffc024d8bc>] sst_module_insert_fixed_block+0x24f/0x26d [snd_soc_sst_dsp]
[   11.883397] PGD 7800b067 PUD 0
[   11.883405] Oops: 0002 [#1] SMP
[   11.886418] gsmi: Log Shutdown Reason 0x03

The virtual address, ffffc90121700000, was out of range. The virtual
address is calculated by adding LPE base address with an offset:

sst_memcpy32(dsp->addr.lpe + data->offset, data->data, data->size);

The offset is calculated in sst_byt_parse_module, by subtraction of
two virtual addresses dsp->addr.fw_ext and dsp->addr.lpe:

block_data.offset = block->ram_offset + (dsp->addr.fw_ext - dsp->addr.lpe);

These virtual addresses are assigned by kernel from ioremap:

sst->addr.lpe = ioremap(pdata->lpe_base, pdata->lpe_size);
sst->addr.fw_ext = ioremap(pdata->fw_base, pdata->fw_size);

In current driver code, offset is defined as unsigned int32:

struct sst_module_data {
...
	u32 offset;		/* offset in FW file */
};

Most of the time kernel assigned virtual addresses with addr.fw_ext
greater than addr.lpe. But sometimes it was the other way round.

Fix the problem by declaring offset as signed int32_t.
Signed-off-by: NWenkai Du <wenkai.du@intel.com>
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Commit 9e1fda4ae158 ("ASoC: dapm: Implement mixer input auto-disable")
is trying to free the widget it allocated by snd_soc_dapm_new_control()
call in dapm_kcontrol_data_alloc() by adding kfree(data->widget) to
dapm_kcontrol_free().

This is causing a widget double free with auto-disabled DAPM kcontrols
in sound card unregistration because widgets are already freed before
dapm_kcontrol_free() is called.

Reason for that is all widgets are added into dapm->card->widgets list
in snd_soc_dapm_new_control() and freed in dapm_free_widgets() during
execution of snd_soc_dapm_free().

Now snd_soc_dapm_free() calls for different DAPM contexts happens before
snd_card_free() call from where the call chain to dapm_kcontrol_free()
begins:

soc_cleanup_card_resources()
  soc_remove_dai_links()
    soc_remove_link_dais()
      snd_soc_dapm_free(&cpu_dai->dapm)
    soc_remove_link_components()
      soc_remove_platform()
        snd_soc_dapm_free(&platform->dapm)
      soc_remove_codec()
        snd_soc_dapm_free(&codec->dapm)
  snd_soc_dapm_free(&card->dapm)
  snd_card_free()
    snd_card_do_free()
      snd_device_free_all()
        snd_device_free()
          snd_ctl_dev_free()
            snd_ctl_remove()
              snd_ctl_free_one()
                dapm_kcontrol_free()

This wasn't making harm with ordinary DAPM kcontrols since data->widget is NULL for
them.

Fixes: 9e1fda4ae158 (ASoC: dapm: Implement mixer input auto-disable)
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

Fix an incorrect sizeof() usage in sst_hsw_stream_get_volume(). sst_dsp_read()
is called to read into a variable of type u32, but is passed sizeof(u32 *) for
argument 'size_t bytes'. Detected by Coverity: CID 1195260.
Signed-off-by: NChristian Engelmayer <cengelma@gmx.at>
Signed-off-by: NMark Brown <broonie@linaro.org>

The intent was to say "sizeof(*pos)" and not "sizeof(pos)".

The sizeof(*pos) is 8 bytes so the bug won't show up on 64 bit systems.
The sizeof(*dx) is 172 bytes so that will be a bugfix.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMark Brown <broonie@linaro.org>