* git://git.linux-nfs.org/pub/linux/nfs-2.6:
  SUNRPC: Fix sparse warnings
  NLM: Fix sparse warnings
  NFS: Fix more sparse warnings
  NFS: Fix some 'sparse' warnings...
  SUNRPC: remove dead variable 'rpciod_running'
  NFS4: Fix incorrect use of sizeof() in fs/nfs/nfs4xdr.c
  NFS: use zero_user_page
  NLM: don't use CLONE_SIGHAND in nlmclnt_recovery
  NLM: Fix locking client timeouts...

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  sata_via: pcim_iomap_regions() conversion missed BAR5
  libata: remove libata.spindown_compat
  sata_nv: fix fallout of devres conversion
  drivers/ata: remove the wildcard from sata_nv driver

pcim_iomap_regions() conversion missed BAR5.  Fix it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

With STANDBYDOWN tracking added, libata.spindown_compat isn't
necessary anymore.  If userspace shutdown(8) issues STANDBYNOW, libata
warns.  If userspace shutdown(8) doesn't issue STANDBYNOW, libata does
the right thing.  Userspace can tell whether kernel supports spindown
by testing whether sysfs node manage_start_stop exists as before.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As with all other drivers, sata_nv's hpriv is allocated with
devm_kzalloc() and there's no need to free it explicitly.  Kill
nv_remove_one() which incorrectly used kfree() instead of devm_kfree()
and use ata_pci_remove_one() directly.

Original fix is from Peer Chen.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Because nvidia SATA controllers onward base on AHCI, so wildcard in sata_nv
driver is unnecessary.  Also the wildcard sometimes cause sata_nv driver to
be loaded for AHCI controllers,which is not as expected.
Signed-off-by: NPeer Chen <pchen@nvidia.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

pci_enable_msi failure is a normal event so we should not print any error.
Going over the code I spotted a missing pci_disable_msi() leak when irq
allocation fails. The whole code also needed a cleanup, so I combined the
two different calls to pci_request_irq into a single call making this
look a lot better. All #ifdef CONFIG_PCI_MSI's have been removed.

Compile tested with both CONFIG_PCI_MSI enabled and disabled.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

pci_enable_msi calls can fail for normal operational reasons. Driver
should not print an error message in that case. Fix a leak that leaves
msi enabled if pci_request_irq fails. We can remove CONFIG_PCI_MSI
ifdefs alltogether
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

NetXen: Fix for driver on System-p
This patch will fix a ping issue on system-p

Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off by: Adhiraj Joshi <adhiraj@netxen.com>
Signed-by: NMithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Spidernet was the driver I original did all the node-aware netdevice
allocation for, but after a year it still hasn't hit mainline.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The hardware must not see that is given ownership of a buffer until it is
completely written, and when the driver receives ownership of a buffer,
it must ensure that any other reads to the buffer reflect its final
state.  Thus, I/O barriers are added where required.

Without this patch, I have observed GCC reordering the setting of
bdp->length and bdp->status in gfar_new_skb.  Hardware reordering
was also theoretically possible.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix link speed detection change.
Thanks to Stefan Roese <sr@denx.de> for finding this bug.

CC: Stefan Roese <sr@denx.de>
Signed-off-by: NEugene Surovegin <ebs@ebshome.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Original patch is from Jeff Haran  <jharan@brocade.com> with my minor style
fixes. His comments follow:

The first problem was in the function that configures the PHY for
autonegotiation, genmii_setup_aneg(). The original code does a
read/modify/write of the autonegotiation advertizement register (reg 4),
followed by a read/modify/write of the control register (reg 0). While
the original code follows the proper procedure as per reading the IEEE
specs, what I found is that on at least one PHY model (National DP83843)
the read of the control register comes back with the soft reset bit set
(bit 15). Because of the read/modify/write operation, this causes the
write to write a 1 back to the reset bit, which initiates a software
reset of the PHY. This software reset causes the PHY to return to its
power up state which advertizes all modes of operation, thus negating
the write to the autoneg advertizement register. The modification is to
spin reading the control register until the soft reset bit is clear
before doing the modify/write.
The second problem was in the function that configures the PHY for
forced operation, genmii_setup_forced(). The original code initiates a
software reset operation via a write of a 1 to bit 15 of the control
register (reg 0), but then proceeds to do a second write to that same
register without waiting until that reset bit is cleared by the PHY
itself (which according to the IEEE specs indicates that the PHY reset
is complete). This is a violation of how one is supposed to use this
software reset feature of these PHYs and I believe was the cause of
mysterious, difficult to reproduce link failures that we've observed on
some of our systems that use this driver. The fix is to modify the
function so that it spins waiting for the reset bit to clear after doing
the soft reset and before doing the subsequent write.
Signed-off-by: NJeff Haran <jharan@brocade.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NEugene Surovegin <ebs@ebshome.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix "Section mismatch" warnings
Signed-off-by: NEugene Surovegin <ebs@ebshome.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Do some memory barrier changes for safety/perfomance:
Don't need read after update to index, mmiowb() followed by read at end
of irq is sufficient.
Signed-off-by: NStephn Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This workaround was added to deal with NAPI core and how
it affected dual port shared polling. It turned out not to
be necessary. Stopping device 0 only doesn't stop NAPI from
working completely after that.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make sure that if we ever get a MIB counter overflow interrupt (normally
masked off), that the IRQ is cleared.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When driver can't allocate receive buffer it drops incoming
packet. Keep a counter.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Align the PHY setup of the sky2 driver with the vendor sk98lin (10.0.4.3)
driver. The PHY register settings are mostly black magic, even with access
to the documentation it isn't clear what the right values are. The changes
are mostly comments, the code change only affects the Yukon FE (100 mbit only)
version.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The problems with Gigabyte motherboards are system configuration dependent.
Since it works fine for some users, it doesn't make sense to deprive
them.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The function ipxrtr_route_packet() takes a 'len' argument of type
size_t. However, its prototype in af_ipx.c incorrectly suggests that the
corresponding argument is of type 'int' instead.

Discovered by building with --combine and letting the compiler see it
all at once.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After a suspend/resume cycle, the UART may have been reset into
low-speed mode -- either because it's actually been reset, or because
the firmware pokes at the old-style divisor registers. If we detected it
as a NS16550A SuperIO chip in the first place and set baud_base to
921600, then we should do so again in the resume path.

This patch adds that code to serial8250_resume_port(), and also makes
serial8250_resume() actually call serial8250_resume_port() for each port
instead of just calling uart_resume_port() directly. And thus fixes
serial port operation after suspend/resume.

It also fixes a bogus comment where we write the EXCR2 register with a
comment saying /* EXCR1 */
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Re-introduce rmap verification patches that Hugh removed when he removed
PG_map_lock. PG_map_lock actually isn't needed to synchronise access to
anonymous pages, because PG_locked and PTL together already do.

These checks were important in discovering and fixing a rare rmap corruption
in SLES9.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

grow_dev_page() simply passes GFP_NOFS to find_or_create_page.  This means
the allocation of radix tree nodes is done with GFP_NOFS and the allocation
of a new page is done using GFP_NOFS.

The mapping has a flags field that contains the necessary allocation flags
for the page cache allocation.  These need to be consulted in order to get
DMA and HIGHMEM allocations etc right.  And yes a blockdev could be
allowing Highmem allocations if its a ramdisk.

Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The sysfs files /sys/power/disk and /sys/power/state do not work as
documented, since they allow the user to write only a few initial
characters of the input string to trigger the option (eg.  'echo pl >
/sys/power/disk' activates the platform mode of hibernation).  Fix it.

Special thanks to Peter Moulder <Peter.Moulder@infotech.monash.edu.au> for
pointing out the problem.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

i_mutex on quota files is special.  Unlike i_mutexes for other inodes it is
acquired under dqonoff_mutex.  Tell lockdep about this lock ranking.  Also
comment and code in quota_sync_sb() seem to be bogus (as i_mutex for quota
file can be acquired under dqonoff_mutex).  Move truncate_inode_pages()
call under dqonoff_mutex and save some problems with races...
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

No other architecture calls check_pgt_cache() from within flush_tlb_mm(),
and i386 is already calling check_pgt_cache() from the usual places,
tlb_finish_mmu() and cpu_idle() (the latter being odd, but not unusual).
flush_tlb_mm() has no business to be freeing pages: remove that line, which
sneaked in with slub's i386 support.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Cc: Andi Kleen <ak@suse.de>
Acked-by: NChristoph Lameter <clameter@sgi.com>
Acked-by: NWilliam Lee Irwin III <wli@holomorphy.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use zero_user_page() instead of open-coding it.
Signed-off-by: NNate Diller <nate.diller@gmail.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make sysctl/kernel/core_pattern and fs/exec.c agree on maximum core
filename size and change it to 128, so that extensive patterns such as
'/local/cores/%e-%h-%s-%t-%p.core' won't result in truncated filename
generation.
Signed-off-by: NDan Aloni <da-x@monatomic.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch add new sub-device-id to support new adapter and changed the
interrupt irq number for unsigned char to unsigned int.

[akpm@osdl.org: fix whitespace in device table]
Signed-off by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make drivers/rtc/Kconfig be clearer about what the various "interfaces"
actually mean, by showing path names.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix typo which breaks build.  How did that happen?
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Loosen gpio_{request,free}() and gpio_direction_{in,out}put() call context
restrictions slightly, so a common idiom is no longer an error: board init
code setting up spinlock-safe GPIOs before tasking is enabled.

The issue was caught by some paranoid code with might_sleep() checks.  The
legacy platform-specific GPIO interfaces stick to spinlock-safe GPIOs, so this
change reflects current implementations and won't break anything.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Andi Kleen pointed out to me that the kernel locking cheat sheet
table entries are unreadable.

Make table entries smaller so that pdf and ps output is readable
(columns were being overwritten and garbled) by using abbreviations.
This allows the tables to fit on one page cleanly.
Add a Legend for the abbreviations:
  SLIS: spin_lock_irqsave
  SLI:  spin_lock_irq
  SL:   spin_lock
  SLBH: spin_lock_bh
  DI:   down_interruptible
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

linux-parport is subscribers-only:

Your mail to 'Linux-parport' with the subject
    Re: [QUESTION] parallel console configuration
Is being held until the list moderator can review it for approval.
The reason it is being held:
    Post by non-member to a members-only list
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It is a known fact that freezeable multithreaded workqueues doesn't like
CPU_DEAD. We keep them only for the incoming CPU-hotplug rework.

Sadly, we can't just kill create_freezeable_workqueue() right now, make
them singlethread.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Refine SCREEN_INFO sanity check for vgacon initialization.

Checking video mode field only to see whenever SCREEN_INFO is
initialized is not enougth, in some cases it is zero although
a vga card is present.  Lets additionally check cols and lines.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Cc: Alan <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>