The driver supports internal and external FDD units so the floppy_open
function must not hard-code the drive location.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: NStan Johnson <userm57@yahoo.com>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NLaurent Vivier <lvivier@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Reading to the end of a 720K disk results in an IO error instead of EOF
because the block layer thinks the disk has 2880 sectors. (Partly this
is a result of inverted logic of the ONEMEG_MEDIA bit that's now fixed.)

Initialize the density and head count in swim_add_floppy() to agree
with the device size passed to set_capacity() during drive probe.

Call set_capacity() again upon device open, after refreshing the density
and head count values.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: NStan Johnson <userm57@yahoo.com>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NLaurent Vivier <lvivier@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

The SWIM chip is compatible with GCR-mode Sony 400K/800K drives but
this driver only supports MFM mode. Therefore only Sony FDHD drives
are supported. Skip incompatible drives.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: NStan Johnson <userm57@yahoo.com>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NLaurent Vivier <lvivier@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

The Sony drive status bits use active-low logic. The swim_readbit()
function converts that to 'C' logic for readability. Hence, the
sense of the names of the status bit macros should not be inverted.

Mostly they are correct. However, the TWOMEG_DRIVE, MFM_MODE and
TWOMEG_MEDIA macros have inverted sense (like MkLinux). Fix this
inconsistency and make the following patches less confusing.

The same problem affects swim3.c so fix that too.

No functional change.

The FDHD drive status bits are documented in sonydriv.cpp from MAME
and in swimiii.h from MkLinux.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: NStan Johnson <userm57@yahoo.com>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NLaurent Vivier <lvivier@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

The 'eject' shell command may send various different ioctl commands.
This leads to error messages on the console even though the FDEJECT
ioctl succeeds.

~# eject floppy
SWIM floppy_ioctl: unknown cmd 21257
SWIM floppy_ioctl: unknown cmd 1

Don't log an error message for an invalid ioctl, just do as the
swim3 driver does and return -ENOTTY.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: NStan Johnson <userm57@yahoo.com>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NLaurent Vivier <lvivier@redhat.com>
Reviewed-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Fixes: 103db8b2 ("[PATCH] swim: stop sharing request queue across multiple gendisks")
Tested-by: NStan Johnson <userm57@yahoo.com>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NLaurent Vivier <lvivier@redhat.com>
Reviewed-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

In the floppy_find() function in swim.c is a call to
get_disk(swd->unit[drive].disk). The actual parameter to this call
can be a NULL pointer when drive == swd->floppy_count. This causes
an oops in get_disk().

Data read fault at 0x00000198 in Super Data (pc=0x1be5b6)
BAD KERNEL BUSERR
Oops: 00000000
Modules linked in: swim_mod ipv6 mac8390
PC: [<001be5b6>] get_disk+0xc/0x76
SR: 2004  SP: 9a078bc1  a2: 0213ed90
d0: 00000000    d1: 00000000    d2: 00000000    d3: 000000ff
d4: 00000002    d5: 02983590    a0: 02332e00    a1: 022dfd64
Process dd (pid: 285, task=020ab25b)
Frame format=B ssw=074d isc=4a88 isb=6732 daddr=00000198 dobuf=00000000
baddr=001be5bc dibuf=bfffffff ver=f
Stack from 022dfca4:
        00000000 0203fc00 0213ed90 022dfcc0 02982936 00000000 00200000 022dfd08
        0020f85a 00200000 022dfd64 02332e00 004040fc 00000014 001be77e 022dfd64
        00334e4a 001be3f8 0800001d 022dfd64 01c04b60 01c04b70 022aba80 029828f8
        02332e00 022dfd2c 001be7ac 0203fc00 00200000 022dfd64 02103a00 01c04b60
        01c04b60 0200e400 022dfd68 000e191a 00200000 022dfd64 02103a00 0800001d
        00000000 00000003 000b89de 00500000 02103a00 01c04b60 02103a08 01c04c2e
Call Trace: [<02982936>] floppy_find+0x3e/0x4a [swim_mod]
 [<00200000>] uart_remove_one_port+0x1a2/0x260
 [<0020f85a>] kobj_lookup+0xde/0x132
 [<00200000>] uart_remove_one_port+0x1a2/0x260
 [<001be77e>] get_gendisk+0x0/0x130
 [<00334e4a>] mutex_lock+0x0/0x2e
 [<001be3f8>] disk_block_events+0x0/0x6c
 [<029828f8>] floppy_find+0x0/0x4a [swim_mod]
 [<001be7ac>] get_gendisk+0x2e/0x130
 [<00200000>] uart_remove_one_port+0x1a2/0x260
 [<000e191a>] __blkdev_get+0x32/0x45a
 [<00200000>] uart_remove_one_port+0x1a2/0x260
 [<000b89de>] complete_walk+0x0/0x8a
 [<000e1e22>] blkdev_get+0xe0/0x29a
 [<000e1fdc>] blkdev_open+0x0/0xb0
 [<000b89de>] complete_walk+0x0/0x8a
 [<000e1fdc>] blkdev_open+0x0/0xb0
 [<000e01cc>] bd_acquire+0x74/0x8a
 [<000e205c>] blkdev_open+0x80/0xb0
 [<000e1fdc>] blkdev_open+0x0/0xb0
 [<000abf24>] do_dentry_open+0x1a4/0x322
 [<00020000>] __do_proc_douintvec+0x22/0x27e
 [<000b89de>] complete_walk+0x0/0x8a
 [<000baa62>] link_path_walk+0x0/0x48e
 [<000ba3f8>] inode_permission+0x20/0x54
 [<000ac0e4>] vfs_open+0x42/0x78
 [<000bc372>] path_openat+0x2b2/0xeaa
 [<000bc0c0>] path_openat+0x0/0xeaa
 [<0004463e>] __irq_wake_thread+0x0/0x4e
 [<0003a45a>] task_tick_fair+0x18/0xc8
 [<000bd00a>] do_filp_open+0xa0/0xea
 [<000abae0>] do_sys_open+0x11a/0x1ee
 [<00020000>] __do_proc_douintvec+0x22/0x27e
 [<000abbf4>] SyS_open+0x1e/0x22
 [<00020000>] __do_proc_douintvec+0x22/0x27e
 [<00002b40>] syscall+0x8/0xc
 [<00020000>] __do_proc_douintvec+0x22/0x27e
 [<0000c00b>] dyadic+0x1/0x28
Code: 4e5e 4e75 4e56 fffc 2f0b 2f02 266e 0008 <206b> 0198 4a88 6732 2428 002c 661e 486b 0058 4eb9 0032 0b96 588f 4a88 672c 2008
Disabling lock debugging due to kernel taint

Fix the array index bounds check to avoid this.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Fixes: 8852ecd9 ("[PATCH] m68k: mac - Add SWIM floppy support")
Tested-by: NStan Johnson <userm57@yahoo.com>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NLaurent Vivier <lvivier@redhat.com>
Reviewed-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

For reasons I don't understand, calling ioremap() then iounmap() on
the SWIM MMIO region causes a hang on 68030 (but not on 68040).

~# modprobe swim_mod
SWIM floppy driver Version 0.2 (2008-10-30)
SWIM device not found !
watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [modprobe:285]
Modules linked in: swim_mod(+)
Format 00  Vector: 0064  PC: 000075aa  Status: 2000    Not tainted
ORIG_D0: ffffffff  D0: d00c0000  A2: 007c2370  A1: 003f810c
A0: 00040000  D5: d0096800  D4: d0097e00
D3: 00000001  D2: 00000003  D1: 00000000
Non-Maskable Interrupt
Modules linked in: swim_mod(+)
PC: [<000075ba>] __iounmap+0x24/0x10e
SR: 2000  SP: 007abc48  a2: 007c2370
d0: d00c0000    d1: 000001a0    d2: 00000019    d3: 00000001
d4: d0097e00    d5: d0096800    a0: 00040000    a1: 003f810c
Process modprobe (pid: 285, task=007c2370)
Frame format=0
Stack from 007abc7c:
        ffffffed 00000000 006a4060 004712e0 007abca0 000076ea d0080000 00080000
        010bb4b8 007abcd8 010ba542 d0096000 00000000 00000000 00000001 010bb59c
        00000000 007abf30 010bb4b8 0047760a 0047763c 00477612 00616540 007abcec
        0020a91a 00477600 0047760a 010bb4cc 007abd18 002092f2 0047760a 00333b06
        007abd5c 00000000 0047760a 010bb4cc 00404f90 004776b8 00000001 007abd38
        00209446 010bb4cc 0047760a 010bb4cc 0020938e 0031f8be 00616540 007abd64
Call Trace: [<000076ea>] iounmap+0x46/0x5a
 [<00080000>] shrink_page_list+0x7f6/0xe06
 [<010ba542>] swim_probe+0xe4/0x496 [swim_mod]
 [<0020a91a>] platform_drv_probe+0x20/0x5e
 [<002092f2>] driver_probe_device+0x21c/0x2b8
 [<00333b06>] mutex_lock+0x0/0x2e
 [<00209446>] __driver_attach+0xb8/0xce
 [<0020938e>] __driver_attach+0x0/0xce
 [<0031f8be>] klist_next+0x0/0xa0
 [<00207562>] bus_for_each_dev+0x74/0xba
 [<000344c0>] blocking_notifier_call_chain+0x0/0x20
 [<00333b06>] mutex_lock+0x0/0x2e
 [<00208e44>] driver_attach+0x1a/0x1e
 [<0020938e>] __driver_attach+0x0/0xce
 [<00207e26>] bus_add_driver+0x188/0x234
 [<000344c0>] blocking_notifier_call_chain+0x0/0x20
 [<00209894>] driver_register+0x58/0x104
 [<000344c0>] blocking_notifier_call_chain+0x0/0x20
 [<010bd000>] swim_init+0x0/0x2c [swim_mod]
 [<0020a7be>] __platform_driver_register+0x38/0x3c
 [<010bd028>] swim_init+0x28/0x2c [swim_mod]
 [<000020dc>] do_one_initcall+0x38/0x196
 [<000344c0>] blocking_notifier_call_chain+0x0/0x20
 [<003331cc>] mutex_unlock+0x0/0x3e
 [<00333b06>] mutex_lock+0x0/0x2e
 [<003331cc>] mutex_unlock+0x0/0x3e
 [<00333b06>] mutex_lock+0x0/0x2e
 [<003331cc>] mutex_unlock+0x0/0x3e
 [<00333b06>] mutex_lock+0x0/0x2e
 [<003331cc>] mutex_unlock+0x0/0x3e
 [<00333b06>] mutex_lock+0x0/0x2e
 [<00075008>] __free_pages+0x0/0x38
 [<000045c0>] mangle_kernel_stack+0x30/0xda
 [<000344c0>] blocking_notifier_call_chain+0x0/0x20
 [<003331cc>] mutex_unlock+0x0/0x3e
 [<00333b06>] mutex_lock+0x0/0x2e
 [<0005ced4>] do_init_module+0x42/0x266
 [<010bd000>] swim_init+0x0/0x2c [swim_mod]
 [<000344c0>] blocking_notifier_call_chain+0x0/0x20
 [<0005eda0>] load_module+0x1a30/0x1e70
 [<0000465d>] mangle_kernel_stack+0xcd/0xda
 [<00331c64>] __generic_copy_from_user+0x0/0x46
 [<0033256e>] _cond_resched+0x0/0x32
 [<00331b9c>] memset+0x0/0x98
 [<0033256e>] _cond_resched+0x0/0x32
 [<0005f25c>] SyS_init_module+0x7c/0x112
 [<00002000>] _start+0x0/0x8
 [<00002000>] _start+0x0/0x8
 [<00331c82>] __generic_copy_from_user+0x1e/0x46
 [<0005f2b2>] SyS_init_module+0xd2/0x112
 [<0000465d>] mangle_kernel_stack+0xcd/0xda
 [<00002b40>] syscall+0x8/0xc
 [<0000465d>] mangle_kernel_stack+0xcd/0xda
 [<0008c00c>] pcpu_balance_workfn+0xb2/0x40e
Code: 2200 7419 e4a9 e589 2841 d9fc 0000 1000 <2414> 7203 c282 7602 b681 6600 0096 0242 fe00 0482 0000 0000 e9c0 11c3 ed89 2642

There's no need to call ioremap() for the SWIM address range, as it lies
within the usual IO device region at 0x5000 0000, which has already been
mapped by head.S.

Remove the redundant ioremap() and iounmap() calls to fix the hang.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: NStan Johnson <userm57@yahoo.com>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NLaurent Vivier <lvivier@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

We ran into an issue with loop and btrfs, where btrfs would complain about
checksum errors. It turns out that is because we don't handle short reads
at all, we just zero fill the remainder. Worse than that, we don't handle
the filling properly, which results in loop trying to advance a single
bio by much more than its size, since it doesn't take chaining into
account.

Handle short reads appropriately, by simply retrying at the new correct
offset. End the remainder of the request with EIO, if we get a 0 read.

Fixes: bc07c10a ("block: loop: support DIO & AIO")
Reviewed-by: NMing Lei <ming.lei@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

We can always get at the request from the payload, no need to store
a pointer to it.
Reviewed-by: NMing Lei <ming.lei@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

When blk_queue_enter() waits for a queue to unfreeze, or unset the
PREEMPT_ONLY flag, do not allow it to be interrupted by a signal.

The PREEMPT_ONLY flag was introduced later in commit 3a0a5299
("block, scsi: Make SCSI quiesce and resume work reliably").  Note the SCSI
device is resumed asynchronously, i.e. after un-freezing userspace tasks.

So that commit exposed the bug as a regression in v4.15.  A mysterious
SIGBUS (or -EIO) sometimes happened during the time the device was being
resumed.  Most frequently, there was no kernel log message, and we saw Xorg
or Xwayland killed by SIGBUS.[1]

[1] E.g. https://bugzilla.redhat.com/show_bug.cgi?id=1553979

Without this fix, I get an IO error in this test:

# dd if=/dev/sda of=/dev/null iflag=direct & \
  while killall -SIGUSR1 dd; do sleep 0.1; done & \
  echo mem > /sys/power/state ; \
  sleep 5; killall dd  # stop after 5 seconds

The interruptible wait was added to blk_queue_enter in
commit 3ef28e83 ("block: generic request_queue reference counting").
Before then, the interruptible wait was only in blk-mq, but I don't think
it could ever have been correct.
Reviewed-by: NBart Van Assche <bart.vanassche@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: NAlan Jenkins <alan.christopher.jenkins@gmail.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Pull overlayfs updates from Miklos Szeredi:
 "In addition to bug fixes and cleanups there are two new features from
  Amir:

   - Consistent inode number support for the case when layers are not
     all on the same filesystem (feature is dubbed "xino").

   - Optimize overlayfs file handle decoding. This one touches the
     exportfs interface to allow detecting the disconnected directory
     case"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: update documentation w.r.t "xino" feature
  ovl: add support for "xino" mount and config options
  ovl: consistent d_ino for non-samefs with xino
  ovl: consistent i_ino for non-samefs with xino
  ovl: constant st_ino for non-samefs with xino
  ovl: allocate anon bdev per unique lower fs
  ovl: factor out ovl_map_dev_ino() helper
  ovl: cleanup ovl_update_time()
  ovl: add WARN_ON() for non-dir redirect cases
  ovl: cleanup setting OVL_INDEX
  ovl: set d->is_dir and d->opaque for last path element
  ovl: Do not check for redirect if this is last layer
  ovl: lookup in inode cache first when decoding lower file handle
  ovl: do not try to reconnect a disconnected origin dentry
  ovl: disambiguate ovl_encode_fh()
  ovl: set lower layer st_dev only if setting lower st_ino
  ovl: fix lookup with middle layer opaque dir and absolute path redirects
  ovl: Set d->last properly during lookup
  ovl: set i_ino to the value of st_ino for NFS export

Pull thermal management update from Zhang Rui:

 - Fix race condition in imx_thermal_probe() (Mikhail Lappo)

 - Add cooling device's statistics in sysfs (Viresh Kumar)

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: Add cooling device's statistics in sysfs
  thermal: imx: Fix race condition in imx_thermal_probe()

Pull dmi updates from Jean Delvare.

* 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  firmware: dmi_scan: Use lowercase letters for UUID
  firmware: dmi_scan: Add DMI_OEM_STRING support to dmi_matches
  firmware: dmi_scan: Fix UUID length safety check

Merge tag 'chrome-platform-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform

Pull chrome platform updates from Benson Leung:

 - a series from Dmitry to remove platform data from chromeos_laptop.c,
   which was the only user of platform data for the atmel_mxt_ts driver.

 - a series to clean up sysfs and debugfs for cros_ec

 - other misc cleanups

* tag 'chrome-platform-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform: (22 commits)
  platform/chrome: mfd/cros_ec_dev: Add sysfs entry to set keyboard wake lid angle
  platform/chrome: cros_ec_debugfs: Add PD port info to debugfs
  platform/chrome: cros_ec_debugfs: Use octal permissions '0444'
  platform/chrome: cros_ec_sysfs: use permission-specific DEVICE_ATTR variants
  platform/chrome: cros_ec_sysfs: introduce to_cros_ec_dev define.
  platform/chrome: cros_ec_sysfs: Modify error handling
  platform/chrome: cros_ec_lpc: Add support for Google devices using custom coreboot firmware
  platform/chrome: cros_ec_lpc: wake up from s2idle on Chrome EC
  Input: atmel_mxt_ts - remove platform data support
  platform/chrome: chromeos_laptop - discard data for unneeded boards
  platform/chrome: chromeos_laptop - use device properties for Pixel
  platform/chrome: chromeos_laptop - rely on I2C to set up interrupt trigger
  platform/chrome: chromeos_laptop - use I2C notifier to create devices
  platform/chrome: chromeos_laptop - parse DMI IRQ data once
  platform/chrome: chromeos_laptop - rework i2c peripherals initialization
  platform/chrome: chromeos_laptop - factor out getting IRQ from DMI
  platform/chrome: chromeos_laptop - introduce pr_fmt()
  platform/chrome: chromeos_laptop - stop setting suspend mode for Atmel devices
  platform/chrome: chromeos_laptop - add SPDX identifier
  Input: atmel_mxt_ts - switch ChromeOS ACPI devices to generic props
  ...

Pull clk updates from Stephen Boyd:
 "The large diff this time around is from the addition of a new clk
  driver for the TI Davinci family of SoCs. So far those clks have been
  supported with a custom implementation of the clk API in the arch port
  instead of in the CCF. With this driver merged we're one step closer
  to having a single clk API implementation.

  The other large diff is from the Amlogic clk driver that underwent
  some major surgery to use regmap. Beyond that, the biggest hitter is
  Samsung which needed some reworks to properly handle clk provider
  power domains and a bunch of PLL rate updates.

  The core framework was fairly quiet this round, just getting some
  cleanups and small fixes for some of the more esoteric features. And
  the usual set of driver non-critical fixes, cleanups, and minor
  additions are here as well.

  Core:
   - Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
   - debugfs ops macroized to shave some lines of boilerplate code
   - Always calculate the phase instead of caching it in clk_get_phase()
   - More __must_check on bulk clk APIs

  New Drivers:
   - TI's Davinci family of SoCs
   - Intel's Stratix10 SoC
   - stm32mp157 SoC
   - Allwinner H6 CCU
   - Silicon Labs SI544 clock generator chip
   - Renesas R-Car M3-N and V3H SoCs
   - i.MX6SLL SoCs

  Removed Drivers:
   - ST-Ericsson AB8540/9540

  Updates:
   - Mediatek MT2701 and MT7622 audsys support and MT2712 updates
   - STM32F469 DSI and STM32F769 sdmmc2 support
   - GPIO clks can sleep now
   - Spreadtrum SC9860 RTC clks
   - Nvidia Tegra MBIST workarounds and various minor fixes
   - Rockchip phase handling fixes and a memory leak plugged
   - Renesas drivers switch to readl/writel from clk_readl/clk_writel
   - Renesas gained CPU (Z/Z2) and watchdog support
   - Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
   - Qualcomm PM8921 PMIC XO buffers
   - Amlogic migrates to regmap APIs
   - TI Keystone clk latching support
   - Allwinner H3 and H5 video clk fixes
   - Broadcom BCM2835 PLLs needed another bit to enable
   - i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
   - i.MX6UL/ULL epdc_podf support
   - Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (233 commits)
  clk: davinci: add a reset lookup table for psc0
  clk: imx: add clock driver for imx6sll
  dt-bindings: imx: update clock doc for imx6sll
  clk: imx: add new gate/gate2 wrapper funtion
  clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux
  clk: cs2000: set pm_ops in hibernate-compatible way
  clk: bcm2835: De-assert/assert PLL reset signal when appropriate
  clk: imx7d: Move clks_init_on before any clock operations
  clk: imx7d: Correct ahb clk parent select
  clk: imx7d: Correct dram pll type
  clk: imx7d: Add USB clock information
  clk: socfpga: stratix10: add clock driver for Stratix10 platform
  dt-bindings: documentation: add clock bindings information for Stratix10
  clk: ti: fix flag space conflict with clkctrl clocks
  clk: uniphier: add additional ethernet clock lines for Pro4
  clk: uniphier: add SATA clock control support
  clk: uniphier: add PCIe clock control support
  clk: Add driver for the si544 clock generator chip
  clk: davinci: Remove redundant dev_err calls
  clk: uniphier: add ethernet clock control support for PXs3
  ...

Merge tag 'pwm/for-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm updates from Thierry Reding:
 "This set of changes adds support for more generations of the RCar
  controller as well as runtime PM support. The JZ4740 driver gains
  support for device tree and can now be used on all Ingenic SoCs.

  Rounding things off is a random assortment of fixes and cleanups all
  across the board"

* tag 'pwm/for-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (29 commits)
  pwm: rcar: Add suspend/resume support
  pwm: rcar: Use PM Runtime to control module clock
  dt-bindings: pwm: rcar: Add bindings for R-Car M3N support
  pwm: rcar: Fix a condition to prevent mismatch value setting to duty
  pwm: sysfs: Use put_device() instead of kfree()
  dt-bindings: pwm: sunxi: Add new compatible strings
  pwm: sun4i: Simplify controller mapping
  pwm: sun4i: Drop unused .has_rdy member
  pwm: sun4i: Properly check current state
  pwm: Remove depends on AVR32
  pwm: stm32: LPTimer: Use 3 cells ->of_xlate()
  dt-bindings: pwm-stm32-lp: Add #pwm-cells
  pwm: stm32: Protect common prescaler for all channels
  pwm: stm32: Remove unused struct device
  pwm: mediatek: Improve precision in rate calculation
  pwm: mediatek: Remove redundant MODULE_ALIAS entries
  pwm: mediatek: Fix up PWM4 and PWM5 malfunction on MT7623
  pwm: jz4740: Enable for all Ingenic SoCs
  pwm: jz4740: Add support for devicetree
  pwm: jz4740: Implement ->set_polarity()
  ...

Pull watchdog updates from Wim Van Sebroeck:

 - Add Nuvoton NPCM watchdog driver

 - renesas_wdt: Add R-Car Gen2 support

 - renesas_wdt: add suspend/resume and restart handler support

 - hpwdt: convert to watchdog core and improve NMI

 - improve timeout setting/handling in various drivers

 - coh901327: make license text and module licence match

 - fix error handling in asm9260_wdt, sprd_wdt and davinci_wdt

 - aspeed imrovements

 - dw improvements (for control register & suspend/resume)

 - add SPDX identifiers for watchdog subsystem

* tag 'linux-watchdog-4.17-rc1' of git://www.linux-watchdog.org/linux-watchdog: (35 commits)
  watchdog: davinci_wdt: fix error handling in davinci_wdt_probe()
  watchdog: add SPDX identifiers for watchdog subsystem
  watchdog: aspeed: Allow configuring for alternate boot
  watchdog: Add Nuvoton NPCM watchdog driver
  dt-bindings: watchdog: Add Nuvoton NPCM description
  watchdog: dw: save/restore control and timeout across suspend/resume
  watchdog: dw: RMW the control register
  watchdog: sprd_wdt: Fix error handling in sprd_wdt_enable()
  watchdog: aspeed: Fix translation of reset mode to ctrl register
  watchdog: renesas_wdt: Add restart handler
  watchdog: renesas_wdt: Add R-Car Gen2 support
  watchdog: renesas_wdt: Add suspend/resume support
  watchdog: f71808e_wdt: Fix WD_EN register read
  watchdog: hpwdt: Update driver version.
  watchdog: hpwdt: Add dynamic debug
  watchdog: hpwdt: Programable Pretimeout NMI
  watchdog: hpwdt: remove allow_kdump module parameter.
  watchdog: hpwdt: condition early return of NMI handler on iLO5
  watchdog: hpwdt: Modify to use watchdog core.
  watchdog: hpwdt: Update nmi_panic message.
  ...

Merge tag 'apparmor-pr-2018-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor

Pull apparmor updates from John Johansen:
 "Features:
  - add base infrastructure for socket mediation. ABI bump and
    additional checks to ensure only v8 compliant policy uses socket af
    mediation.
  - improve and cleanup dfa verification
  - improve profile attachment logic
     - improve overlapping expression handling
     - add the xattr matching to the attachment logic
  - improve signal mediation handling with stacked labels
  - improve handling of no_new_privs in a label stack

  Cleanups and changes:
  - use dfa to parse string split
  - bounded version of label_parse
  - proper line wrap nulldfa.in
  - split context out into task and cred naming to better match usage
  - simplify code in aafs

  Bug fixes:
  - fix display of .ns_name for containers
  - fix resource audit messages when auditing peer
  - fix logging of the existence test for signals
  - fix resource audit messages when auditing peer
  - fix display of .ns_name for containers
  - fix an error code in verify_table_headers()
  - fix memory leak on buffer on error exit path
  - fix error returns checks by making size a ssize_t"

* tag 'apparmor-pr-2018-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor: (36 commits)
  apparmor: fix memory leak on buffer on error exit path
  apparmor: fix dangling symlinks to policy rawdata after replacement
  apparmor: Fix an error code in verify_table_headers()
  apparmor: fix error returns checks by making size a ssize_t
  apparmor: update MAINTAINERS file git and wiki locations
  apparmor: remove POLICY_MEDIATES_SAFE
  apparmor: add base infastructure for socket mediation
  apparmor: improve overlapping domain attachment resolution
  apparmor: convert attaching profiles via xattrs to use dfa matching
  apparmor: Add support for attaching profiles via xattr, presence and value
  apparmor: cleanup: simplify code to get ns symlink name
  apparmor: cleanup create_aafs() error path
  apparmor: dfa split verification of table headers
  apparmor: dfa add support for state differential encoding
  apparmor: dfa move character match into a macro
  apparmor: update domain transitions that are subsets of confinement at nnp
  apparmor: move context.h to cred.h
  apparmor: move task related defines and fns to task.X files
  apparmor: cleanup, drop unused fn __aa_task_is_confined()
  apparmor: cleanup fixup description of aa_replace_profiles
  ...

Pull block fixes from Jens Axboe:
 "Followup fixes for this merge window. This contains:

   - Series from Ming, fixing corner cases in our CPU <-> queue mapping.

     This triggered repeated warnings on especially s390, but I also hit
     it in cpu hot plug/unplug testing while doing IO on NVMe on x86-64.

   - Another fix from Ming, ensuring that we always order budget and
     driver tag identically, avoiding a deadlock on QD=1 devices.

   - Loop locking regression fix from this merge window, from Omar.

   - Another loop locking fix, this time missing an unlock, from Tetsuo
     Handa.

   - Fix for racing IO submission with device removal from Bart.

   - sr reference fix from me, fixing a case where disk change or
     getevents can race with device removal.

   - Set of nvme fixes by way of Keith, from various contributors"

* tag 'for-linus-20180413' of git://git.kernel.dk/linux-block: (28 commits)
  nvme: expand nvmf_check_if_ready checks
  nvme: Use admin command effects for admin commands
  nvmet: fix space padding in serial number
  nvme: check return value of init_srcu_struct function
  nvmet: Fix nvmet_execute_write_zeroes sector count
  nvme-pci: Separate IO and admin queue IRQ vectors
  nvme-pci: Remove unused queue parameter
  nvme-pci: Skip queue deletion if there are no queues
  nvme: target: fix buffer overflow
  nvme: don't send keep-alives to the discovery controller
  nvme: unexport nvme_start_keep_alive
  nvme-loop: fix kernel oops in case of unhandled command
  nvme: enforce 64bit offset for nvme_get_log_ext fn
  sr: get/drop reference to device in revalidate and check_events
  blk-mq: Revert "blk-mq: reimplement blk_mq_hw_queue_mapped"
  blk-mq: Avoid that submitting a bio concurrently with device removal triggers a crash
  backing: silence compiler warning using __printf
  blk-mq: remove code for dealing with remapping queue
  blk-mq: reimplement blk_mq_hw_queue_mapped
  blk-mq: don't check queue mapped in __blk_mq_delay_run_hw_queue()
  ...

Pull more i2c updates from Wolfram Sang:

 - hot bugfix for i801 to make laptops with strange BIOS reboot again
   when using SMBUS Host notify

 - change to MAINTAINERS creating a specific fallback entry for I2C host
   drivers and settings its status to "Odd fixes"

 - a long overdue param checking for the I2C core

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: add param sanity check to i2c_transfer()
  MAINTAINERS: add maintainer for Renesas I2C related drivers
  MAINTAINERS: remove me as maintainer for I2C host drivers
  i2c: i801: Restore configuration at shutdown
  i2c: i801: Save register SMBSLVCMD value only once

Pull arch/sh updates from Rich Felker:
 "Fixes for bugs in futex, device tree, and userspace breakpoint traps,
  and for PCI issues on SH7786"

* tag 'sh-for-4.17' of git://git.libc.org/linux-sh:
  arch/sh: pcie-sh7786: handle non-zero DMA offset
  arch/sh: pcie-sh7786: adjust the memory mapping
  arch/sh: pcie-sh7786: adjust PCI MEM and IO regions
  arch/sh: pcie-sh7786: exclude unusable PCI MEM areas
  arch/sh: pcie-sh7786: mark unavailable PCI resource as disabled
  arch/sh: pci: don't use disabled resources
  arch/sh: make the DMA mapping operations observe dev->dma_pfn_offset
  arch/sh: add sh7786_mm_sel() function
  sh: fix debug trap failure to process signals before return to user
  sh: fix memory corruption of unflattened device tree
  sh: fix futex FUTEX_OP_SET op on userspace addresses

Pull more arm64 updates from Will Deacon:
 "A few late updates to address some issues arising from conflicts with
  other trees:

   - Removal of Qualcomm-specific Spectre-v2 mitigation in favour of the
     generic SMCCC-based firmware call

   - Fix EL2 hardening capability checking, which was bodged to reduce
     conflicts with the KVM tree

   - Add some currently unused assembler macros for managing SIMD
     registers which will be used by some crypto code in the next merge
     window"

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: assembler: add macros to conditionally yield the NEON under PREEMPT
  arm64: assembler: add utility macros to push/pop stack frames
  arm64: Move the content of bpi.S to hyp-entry.S
  arm64: Get rid of __smccc_workaround_1_hvc_*
  arm64: capabilities: Rework EL2 vector hardening entry
  arm64: KVM: Use SMCCC_ARCH_WORKAROUND_1 for Falkor BP hardening

Pull  more s390 updates from Martin Schwidefsky:
 "Three notable larger changes next to the usual bug fixing:

   - update the email addresses in MAINTAINERS for the s390 folks to use
     the simpler linux.ibm.com domain instead of the old
     linux.vnet.ibm.com

   - an update for the zcrypt device driver that removes some old and
     obsolete interfaces and add support for up to 256 crypto adapters

   - a rework of the IPL aka boot code"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (23 commits)
  s390: correct nospec auto detection init order
  s390/zcrypt: Support up to 256 crypto adapters.
  s390/zcrypt: Remove deprecated zcrypt proc interface.
  s390/zcrypt: Remove deprecated ioctls.
  s390/zcrypt: Make ap init functions static.
  MAINTAINERS: update s390 maintainers email addresses
  s390/ipl: remove reipl_method and dump_method
  s390/ipl: correct kdump reipl block checksum calculation
  s390/ipl: remove non-existing functions declaration
  s390: assume diag308 set always works
  s390/ipl: avoid adding scpdata to cmdline during ftp/dvd boot
  s390/ipl: correct ipl parmblock valid checks
  s390/ipl: rely on diag308 store to get ipl info
  s390/ipl: move ipl_flags to ipl.c
  s390/ipl: get rid of ipl_ssid and ipl_devno
  s390/ipl: unite diag308 and scsi boot ipl blocks
  s390/ipl: ensure loadparm valid flag is set
  s390/qdio: lock device while installing IRQ handler
  s390/qdio: clear intparm during shutdown
  s390/ccwgroup: require at least one ccw device
  ...

RFC 4122 asks for letters a-f in UUID to be lowercase. Follow this
recommendation.

Suggested by Paul Dagnelie at:
https://savannah.nongnu.org/bugs/index.php?53569Signed-off-by: NJean Delvare <jdelvare@suse.de>

OEM strings are defined by each OEM and they contain customized and
useful OEM information. Supporting it provides more flexible uses of
the dmi_matches function.
Signed-off-by: NAlex Hung <alex.hung@canonical.com>
Signed-off-by: NJean Delvare <jdelvare@suse.de>

The test which ensures that the DMI type 1 structure is long enough
to hold the UUID is off by one. It would fail if the structure is
exactly 24 bytes long, while that's sufficient to hold the UUID.

I don't expect this bug to cause problem in practice because all
implementations I have seen had length 8, 25 or 27 bytes, in line
with the SMBIOS specifications. But let's fix it still.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Fixes: a814c359 ("firmware: dmi_scan: Check DMI structure length")
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>

Pull drm fixes from Dave Airlie:
 "One omap, and one alsa pm fix (we merged the breaking patch via drm
  tree).

  Otherwise it's two bunches of amdgpu fixes, removing an unneeded file,
  some DC fixes, HDMI audio regression fix, and some vega12 fixes"

* tag 'drm-fixes-for-v4.17-rc1' of git://people.freedesktop.org/~airlied/linux: (27 commits)
  Revert "drm/amd/display: disable CRTCs with NULL FB on their primary plane (V2)"
  Revert "drm/amd/display: fix dereferencing possible ERR_PTR()"
  drm/amd/display: Fix regamma not affecting full-intensity color values
  drm/amd/display: Fix FBC text console corruption
  drm/amd/display: Only register backlight device if embedded panel connected
  drm/amd/display: fix brightness level after resume from suspend
  drm/amd/display: HDMI has no sound after Panel power off/on
  drm/amdgpu: add MP1 and THM hw ip base reg offset
  drm/amdgpu: fix null pointer panic with direct fw loading on gpu reset
  drm/radeon: add PX quirk for Asus K73TK
  drm/omap: fix crash if there's no video PLL
  drm/amdgpu: Fix memory leaks at amdgpu_init() error path
  drm/amdgpu: Fix PCIe lane width calculation
  drm/radeon: Fix PCIe lane width calculation
  drm/amdgpu/si: implement get/set pcie_lanes asic callback
  drm/amdgpu: Add support for SRBM selection v3
  Revert "drm/amdgpu: Don't change preferred domian when fallback GTT v5"
  drm/amd/powerply: fix power reading on Fiji
  drm/amd/powerplay: Enable ACG SS feature
  drm/amdgpu/sdma: fix mask in emit_pipeline_sync
  ...

Pull tracing fixes from Steven Rostedt:
 "A few clean ups and bug fixes:

   - replace open coded "ARRAY_SIZE()" with macro

   - updates to uprobes

   - bug fix for perf event filter on error path"

* tag 'trace-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Enforce passing in filter=NULL to create_filter()
  trace_uprobe: Simplify probes_seq_show()
  trace_uprobe: Use %lx to display offset
  tracing/uprobe: Add support for overlayfs
  tracing: Use ARRAY_SIZE() macro instead of open coding it

Add copyright in two files before they get autorubberstamped.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull PCI fixes from Bjorn Helgaas:

 - mark Extended Tags as broken on Broadcom HT1100 and HT2000 Root Ports
   to fix drm/Xorg hangs and unresponsive keyboards (Sinan Kaya)

 - remove useless messages during resource reassignment (Desnes A. Nunes
   do Rosario)

* tag 'pci-v4.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Remove messages about reassigning resources
  PCI: Mark Broadcom HT1100 and HT2000 Root Port Extended Tags as broken

Pull parisc updates from Helge Deller:

 - fix panic when halting system via "shutdown -h now"

 - drop own coding in favour of generic CONFIG_COMPAT_BINFMT_ELF
   implementation

 - add FPE_CONDTRAP constant: last outstanding parisc-specific cleanup
   for Eric Biedermans siginfo patches

 - move some functions to .init and some to .text.hot linker sections

* 'parisc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Prevent panic at system halt
  parisc: Switch to generic COMPAT_BINFMT_ELF
  parisc: Move cache flush functions into .text.hot section
  parisc/signal: Add FPE_CONDTRAP for conditional trap handling

On SuperH, the base of the physical memory might be different from
zero. In this case, PCI address zero will map to a non-zero physical
address. In order to make sure that the DMA mapping API takes care of
this DMA offset, we must fill in the dev->dma_pfn_offset field for PCI
devices. This gets done in the pcibios_bus_add_device() hook, called
for each new PCI device detected.

The dma_pfn_offset global variable is re-calculated for every PCI
controller available on the platform, but that's not an issue because
its value will each time be exactly the same, as it only depends on
the memory start address and memory size.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NRich Felker <dalias@libc.org>

The code setting up the PCI -> SuperHighway mapping doesn't take into
account the fact that the address stored in PCIELARx must be aligned
with the size stored in PCIELAMRx.

For example, when your physical memory starts at 0x0800_0000 (128 MB),
a size of 64 MB or 128 MB is fine. However, if you have 256 MB of
memory, it doesn't work because the base address is not aligned on the
size.

In such situation, we have to round down the base address to make sure
it is aligned on the size of the area. For for a 0x0800_0000 base
address with 256 MB of memory, we will round down to 0x0, and extend
the size of the mapping to 512 MB.

This allows the mapping to work on platforms that have 256 MB of
RAM. The current setup would only work with 128 MB of RAM or less.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NRich Felker <dalias@libc.org>

The current definition of the PCIe IO and MEM resources for SH7786
doesn't match what the datasheet says. For example, for PCIe0
0xfe100000 is advertised by the datasheet as a PCI IO region, while
0xfd000000 is advertised as a PCI MEM region. The code currently
inverts the two.

The SH4A_PCIEPARL and SH4A_PCIEPTCTLR registers allow to define the
base address and role of the different regions (including whether it's
a MEM or IO region). However, practical experience on a SH7786 shows
that if 0xfe100000 is used for LEL and 0xfd000000 for IO, a PCIe
device using two MEM BARs cannot be accessed at all. Simply using
0xfe100000 for IO and 0xfd000000 for MEM makes the PCIe device
accessible.

It is very likely that this was never seen because there are two other
PCI MEM region listed in the resources. However, for different
reasons, none of the two other MEM regions are usable on the specific
SH7786 platform the problem was encountered. Therefore, the last MEM
region at 0xfe100000 was used to place the BARs, making the device
non-functional.

This commit therefore adjusts those PCI MEM and IO resources
definitions so that they match what the datasheet says. They have only
been tested with PCIe 0.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NRich Felker <dalias@libc.org>

Depending on the physical memory layout, some PCI MEM areas are not
usable. According to the SH7786 datasheet, the PCI MEM area from
1000_0000 to 13FF_FFFF is only usable if the physical memory layout
(in MMSELR) is 1, 2, 5 or 6. In all other configurations, this PCI MEM
area is not usable (because it overlaps with DRAM).

Therefore, this commit adjusts the PCI SH7786 initialization to mark
the relevant PCI resource as IORESOURCE_DISABLED if we can't use it.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NRich Felker <dalias@libc.org>

Some PCI MEM resources are marked as IORESOURCE_MEM_32BIT, which means
they are only usable when the SH core runs in 32-bit mode. In 29-bit
mode, such memory regions are not usable.

The existing code for SH7786 properly skips such regions when
configuring the PCIe controller registers. However, because such
regions are still described in the resource array, the
pcibios_scanbus() function in the SuperH pci.c will register them to
the PCI core. Due to this, the PCI core will allocate MEM areas from
this resource, and assign BARs pointing to this area, even though it's
unusable.

In order to prevent this from happening, we mark such regions as
IORESOURCE_DISABLED, which tells the SuperH pci.c pcibios_scanbus()
function to skip them.

Note that we separate marking the region as disabled from skipping it,
because other regions will be marked as disabled in follow-up patches.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NRich Felker <dalias@libc.org>

In pcibios_scanbus(), we provide to the PCI core the usable MEM and IO
regions using pci_add_resource_offset(). We travel through all
resources available in the "struct pci_channel".

Also, in register_pci_controller(), we travel through all resources to
request them, making sure they don't conflict with already requested
resources.

However, some resources may be disabled, in which case they should not
be requested nor provided to the PCI core.

In the current situation, none of the resources are disabled. However,
follow-up patches in this series will make some resources disabled,
making this preliminary change necessary.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NRich Felker <dalias@libc.org>

Some devices may have a non-zero DMA offset, i.e an offset between the
DMA address and the physical address. Such an offset can be encoded
into the dma_pfn_offset field of "struct device", but the SuperH
implementation of the DMA mapping API does not observe this
information.

This commit fixes that by ensuring the DMA address is properly
calculated depending on this DMA offset.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NRich Felker <dalias@libc.org>