If the L1 entrance latency is not calibrated properly
in the EEPROM in WB222 boards, there could be problems
in connectivity. Check and correct the calibrated value
if it doesn't match the optimal value for WB222, 4us.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for dropping gratuitous ARP frames which is
requirement for WFA Hotspot2.0.

Hotspot2.0 capability is enabled in driver if extended capabilities
IE from BSS descriptor has 11u interworking enabled.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

EXT_CAPAB_IE format involves IEEE header followed by bytestream of
capabilities. Current structure has incorrect member u8 for data;
fix it by defining it as u8[0].
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have usb_deregister() call in our rmmod routine. deauth,
shutdown etc. commands will be sent to FW later when bus
driver calls disconnect handler.

This mechanism works fine with SDIO and PCIe interfaces, but
there is an issue with USB.

USB bus driver returns all URBs submitted for receiving data
and command response immediately after usb_deregister() with
failure status. Hence we don't send deauth, shutdown etc.
command to firmware.

The problem is fixed by moving code from disconnect handler to
rmmod routine for USB interface.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tell the PCIe host core when the wifi is activated.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

replace the calls to bcma_core_pci_extend_L1timer() by calls to the
newly introduced bcma_core_pci_ip() and bcma_core_pci_down()
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The values written into the BCN_OFFSET[01] registers are
hardcoded in the rt2800_init_register function.

Add a macro and a helper function to derive these values
directly from the base address of a given beacon, and use
the new function instead of the hardcoded numbers.

The patch contains no functional changes. The programmed
register values are the same before and after the patch.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The HW_BEACON_BASE() macro returns the base address
of a given beacon, however the returned values are
not usable on all chipsets. On devices which have
selectable shared memory parts, some beacon may be
located in the high part of the shared memory.

Instead of extending the already complicated macro,
add a new helper function and use that to get the
base address of a given beacon.

The actual patch contains no functional changes, the
helper function will be extended in a further patch
to handle different chipsets' requirements.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch completes the changes needed for supporting the
iPA variant cards of the BCM4313 wireless chipset.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When changing channels the TSSI based power control needs to be
reinitialized.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A number of additional phy registers needs to be programmed when
using TSSI-based power control.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rework the code path in lcnphy tbl_init() for switch control
table programming. This also takes the iPA BT-combo card into
account.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For lcnphy revision 1 or when hardware supports i/q calibration the
function wlc_lcnphy_set_txpwr_by_index() was called twice.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The baseband multiplier must be zero during TSSI idle estimation
and restored afterwards.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The gain level control for the test tone has been changed. This
calbration test tone is used to determine the i/q compensation.
The i/q calibration routine has been reworked to accomodate this.

Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the transmit gain table for bcm4313 chip family.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For debug purposes it is good to have the phy and radio information
available in the log. Only logged when driver is built when BRCMDBG
or BRCM_TRACING kconfig are set.
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch converts all sizeof(x)/sizeof(x[0]) instances to
ARRAY_SIZE macro in phytbl_lcn.c. The patch was made using
spatch with ARRAY_SIZE.cocci (see [1]).

[1] https://github.com/coccinelle/coccinelle/tree/master/demos/janitorings

Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function wlc_lcnphy_load_tx_gain_table() has a target PA
gain specified for the iPA variant of the bcm4313. This gain
value is reduced to avoid PA distortion. The if-statement is
removed because it was rather redundant in the first place.
Please note that this patch does not provide full iPA support.

Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cleaning up some code fragments reducing indentation and uncluttering
some lines. Apart from whitespace there are no actual code changes
made.

Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a AR9485/WB225 based card.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bug 60747 - 1286:2044 [Microsoft Surface Pro]
    Marvell 88W8797 wifi show 3 interface under network
https://bugzilla.kernel.org/show_bug.cgi?id=60747

This issue was also reported previously by OLPC and some folks from
the community.

There are 3 network interfaces with different types being created
when mwifiex driver is loaded:

1. mlan0 (infra. STA)
2. uap0 (AP)
3. p2p0 (P2P_CLIENT)

The Network Manager attempts to use all 3 interfaces above without
filtering the managed interface type. As the result, 3 identical
interfaces are displayed under network manager. If user happens to
click on an entry under which its interface is uap0 or p2p0, the
association will fail.

Work around it by removing the creation of AP and P2P interfaces
at driver loading time. These interfaces can be added with 'iw' or
other applications manually when they are needed.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This improves RX diversity and performance for AR9485.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Along with other chipsets, the Ralink driver uses the
frequency adjustment code for RF3053 as well. Remove
the bogus place-holder comment from the RF3053 specific
channel configuration function and call the frequency
adjustment function instead

Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RT3593_ChipSwitchChannel function in chips/rt3593.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the rt2800_adjust_freq_offset function before
the channel configuration functions to make it usable
from those without a forward declaration.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver, the RFCSR17 register can't be programmed in
one step on devices which are using the frequency
offset adjustment code.

Update the code to use step-by-step adjustment.

Reference:
  RT30xxWriteRFRegister function in common/rt_rf.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to the Ralink driver, there is an MCU
command which can be used to send the frequency
offset value directly to the USB device without
going through the RFCSR writing sequence.

Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't write the new value into the register if it is
the same as the old value to avoid unncessary USB bus
traffic with USB devices. The change also saves a few
cycle on MMIO based devices.

Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current code in the 'rt2800_adjust_freq_offset'
function limits the device specific frequency offset
value to FREQ_BOUND but ignores the fact that the
uppermost bit is not part of the frequency offset
value. As the result, the driver always uses the
FREQ_BOUND value if the uppermost bit is set.

Update the code to use the correct source value
for calculating the boundary.

Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of precomputing the beacon base in
each caller, pass the beacon index to the
'rt2800_clear_beacon_register' function
and compute the beacon base in there.

This allows to simplify the caller functions
a bit.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The name of the HW_BEACON_OFFSET macro is a
bit confusing. It returns with one of the
HW_BEACON_BASE* values, so rename the macro
to HW_BEACON_BASE to reflect that.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 2011_1007_RT5390_RT5392_Linux_STA_V2.5.0.3_DPO
driver enables PCIe wakeup for these chips as well.
Do the same in rt2x00.

References:
  rt28xx_init in common/rtmp_init_intf.c
  RTMPInitPCIeLinkCtrlValue in os/linux/rt_rbus_pci_drv.c
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rt2800pci driver uses the same [RT]XWI size
for all chipsets, however some chips requires
different values.

The size of the [RT]XWI structures is a constant
value for a given chipset and it does not depend
on the underlying interface. Add a helper function
which returns the correct values for the actual
chipset and use the new helper both in the rt2800usb
and in the rt2800pci drivers. This ensures that both
drivers are using the correct values.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CSA is only enabled for one interface, but the same limitation applies
for mac80211 too. It checks whether the beacon has been sent (different
approaches for non-EDMA-enabled and EDMA-enabled devices), and completes
the channel switch after that.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>