The Tegra30 I2S driver was writing the AHUB interface parameters to the
playback path register rather than the capture path register. This
caused the capture parameters not to be configured at all, so if
capturing using non-HW-default parameters (e.g. 16-bit stereo rather
than 8-bit mono) the audio would be corrupted.

With this fixed, audio capture from an analog microphone works correctly
on the Cardhu board.

Cc: stable@vger.kernel.org
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

CS42L52 Beep control uses 2dB scale from -56dB
Signed-off-by: NBrian Austin <brian.austin@cirrus.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Beep Volume Min/Max was backwards.
Change to SOC_SONGLE_SX_TLV for correct volume representation
Signed-off-by: NBrian Austin <brian.austin@cirrus.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@kernel.org

list_first_entry() will always return a valid pointer, even if the list is
empty. So the check whether path is NULL will always be false. So we end up
calling dapm_create_or_share_mixmux_kcontrol() with a path struct that points
right in the middle of the widget struct and by trying to modify the path the
widgets memory will become corrupted. Fix this by using list_emtpy() to check if
the widget doesn't have any paths.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

The SGTL5000 Capture Attenuate Switch (or "ADC Volume Range Reduction"
as it is called in the manual) is single bit only.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

When a sound capture/playback is terminated while a playback/capture
is running, power_vag_event() will clear SGTL5000_CHIP_ANA_POWER in
the SND_SOC_DAPM_PRE_PMD event, thus muting the respective other
channel.

Don't clear SGTL5000_CHIP_ANA_POWER when both DAC and ADC are active
to prevent this.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

If kzalloc() fails for `img' then we are going to leak the memory
for `out'.  We are freeing the memory of all the tx/rx transfers
but the tx/rx buf pointers will be NULL if we drop out earlier.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

d8b51c11 [ASoC: ac97c: Use
module_platform_driver()] broke the build:

 CC      sound/soc/au1x/ac97c.o
/home/ralf/src/linux/upstream-sfr/sound/soc/au1x/ac97c.c:344:1: error: expected identifier or ‘(’ before ‘&’ token
/home/ralf/src/linux/upstream-sfr/sound/soc/au1x/ac97c.c:344:1: error: pasting "__initcall_" and "&" does not give a valid preprocessing token
/home/ralf/src/linux/upstream-sfr/sound/soc/au1x/ac97c.c:344:1: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘&’ token
/home/ralf/src/linux/upstream-sfr/sound/soc/au1x/ac97c.c:344:1: error: expected identifier or ‘(’ before ‘&’ token
/home/ralf/src/linux/upstream-sfr/sound/soc/au1x/ac97c.c:344:1: error: pasting "__exitcall_" and "&" does not give a valid preprocessing token
/home/ralf/src/linux/upstream-sfr/sound/soc/au1x/ac97c.c:344:1: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘&’ token
/home/ralf/src/linux/upstream-sfr/sound/soc/au1x/ac97c.c:334:31: warning: ‘au1xac97c_driver’ defined but not used [-Wunused-variable]
make[5]: *** [sound/soc/au1x/ac97c.o] Error 1
make[4]: *** [sound/soc/au1x] Error 2
make[3]: *** [sound/soc] Error 2
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

If CONFIG_SND_BF5XX_HAVE_COLD_RESET is enabled building the blackfin ac97 driver
fails with the following compile error:
	sound/soc/blackfin/bf5xx-ac97.c: In function ‘asoc_bfin_ac97_probe’:
	sound/soc/blackfin/bf5xx-ac97.c:297: error: expected ‘;’ before ‘{’ token
	sound/soc/blackfin/bf5xx-ac97.c:302: error: label ‘gpio_err’ used but not defined

The issue was introduced in commit 6dab2fd7 ("ASoC: bf5xx-ac97: Convert to
devm_gpio_request_one()").
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

As part of the multiplatform refactoring for AC'97 the AC'97 bus ops were
staticised meaning that the prototype (which was never needed) conflicts
with the declaration causing build failures.
Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>

The ALSA core expect the put callback of a control to return 1 if the value of
the control changed and 0 if it did not. Both snd_soc_dapm_put_volsw() and
snd_soc_dapm_put_enum_virt() currently always returns 0. For both functions we
already have a 'change' variable which either contains 1 or 0 depending on
whether the value has changed or not, so just return that.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The errors were caused by copy/paste mistake in below commit
since v3.10:
3489d506 ASoC: tegra: Use common DAI DMA data struct

It also corrects slave_id initialization in tegra20_ac97 driver.
Signed-off-by: NRichard Zhao <rizhao@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLucas Stach <dev@lynxeye.de>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org> # 3.10

There are three callers for this function, and none of them want it to
free platform for them.  It leads to a double free.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Fix the build of this driver. It was broken by:

Commit 453807f3
ASoC: ep93xx: Use ep93xx_dma_params instead of ep93xx_pcm_dma_params

The removed struct ep93xx_pcm_dma_params use the member 'dma_port' to
select the dma channel. The struct ep93xx_dma_data uses the member
'port'.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

It's not always the case that clock is already available when sgtl5000
get probed at the first time, e.g. the clock is provided by CPU DAI
which may be probed after sgtl5000.  So let's defer the probe when
devm_clk_get() call fails and give it chance to try later.

It fixes the regression on imx28 since commit 9e13f345 (ASoC: sgtl5000:
Let the codec acquire its clock).

[    1.927637] sgtl5000 0-000a: Failed to get mclock: -2
[    1.934280] sgtl5000: probe of 0-000a failed with error -2
[    1.945906] mxs-sgtl5000 sound.13: ASoC: CODEC (null) not registered
[    1.953787] mxs-sgtl5000 sound.13: snd_soc_register_card failed (-517)
[    1.960865] platform sound.13: Driver mxs-sgtl5000 requests probe deferral
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

snd_pcm_stop() must be called in the PCM substream lock context.

Cc: <stable@vger.kernel.org>
Acked-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

snd_pcm_stop() must be called in the PCM substream lock context.

Cc: <stable@vger.kernel.org>
Acked-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The registers of max98088 are 8 bits, not 16 bits. This bug causes the
contents of registers to be overwritten with bad values when the codec
is suspended and then resumed.
Signed-off-by: NChih-Chung Chang <chihchung@chromium.org>
Signed-off-by: NDylan Reid <dgreid@chromium.org>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

wm8978 needs .symmetric_rates = 1.
The playback/capture will be strange without this patch
when it used asymmetric rate in same time
Tested-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The DMA resource no longer available via this API when booting with DT.
When the board is booted with DT do not use platform_get_resource_byname(),
instead set the dma_data.filter_data to the name of the DMA channel and omap-pcm
can use this name to request the DMA channel.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The DMA resource no longer available via this API when booting with DT.
DMIC is only available on OMAP4/5 and both can boot with DT only.
Set the dma_data.filter_data to the DMA name which will be used by omap-pcm
to request the DMA channel.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The DMA resource no longer available via this API when booting with DT.
McPDM is only available on OMAP4/5 and both can boot with DT only.
Set the dma_data.filter_data to the DMA name which will be used by omap-pcm
to request the DMA channel.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

When booting with DT the platform_get_resource_byname() is not available to
get the DMA resource. In this case the DAI drivers will set the filter_data to
the name of the DMA and omap-pcm can use this to request the DMA channel.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

As per the User Manual, the RFS and BFS should be set in slave mode
for correct operation.
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Reviewed-by: NSimon Glass <sjg@google.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This was committed in error.
Signed-off-by: NMark Brown <broonie@linaro.org>

SGTL5000_PLL_FRAC_DIV_MASK is used to mask bits 0-10 (11 bits in total) of
register CHIP_PLL_CTRL, so fix the mask to accomodate all this bit range.
Reported-by: NOskar Schirmer <oskar@scara.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

According to the sgtl5000 reference manual, the default value of CHIP_SSS_CTRL
is 0x10.
Reported-by: NOskar Schirmer <oskar@scara.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

There is an error in merge commit 384b8345 on conflict resolution which
causes the following NULL pdata pointer bug.

wm8962 0-001a: customer id 0 revision D
Unable to handle kernel NULL pointer dereference at virtual address 00000004
pgd = 80004000
[00000004] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.0+ #1
task: bf870000 ti: bf874000 task.ti: bf874000
PC is at wm8962_probe+0x134/0x6c8
LR is at regmap_unlock_mutex+0x10/0x14
pc : [<80452100>]    lr : [<80304cf4>]    psr: a0000113
sp : bf875c98  ip : 00000000  fp : bf875cd4
r10: 00000000  r9 : bfb1830c  r8 : 80779bc4
r7 : 00000000  r6 : 00000001  r5 : bfbac010  r4 : bfb33e00
r3 : 80304ce4  r2 : 00000000  r1 : 00000001  r0 : fffffffb
Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c53c7d  Table: 1000404a  DAC: 00000017
Process swapper/0 (pid: 1, stack limit = 0xbf874238)
Stack: (0xbf875c98 to 0xbf876000)
...

Fix the error by assigning pdata a correct pointer.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

If the ssi or codec drivers are not loaded (for instance, because spi or i2c
bus drivers are not loaded), returning -EINVAL will for people to unload and
then reload the module to get sound working. Returning E_PROBE_DEFER will
mitigate this.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

There is a typo in the filename (i2c mentioned instead of i2s).
However, this is a redundant piece of information. Delete it
altogether.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

We still need video & sound drivers with device tree enabled.
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NTony Lindgren <tony@atomide.com>

spacr64 gcc-3.4.5 (at least) spits this back.

Cc: Andrey Smirnov <andrey.smirnov@convergeddevices.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since the Samsung platforms have moved to pinctrl for pin muxing and that
is handled in the core the old GPIO based muxing code can just be removed.
Something similar had been submitted by Thomas Abraham back in March but
a resubmission following review never happened.
Signed-off-by: NMark Brown <broonie@linaro.org>

Mostly the mxs system design uses saif0 mclk output as the clock source
of codec.  Since the mclk is implemented as a general divider with the
saif clk as the parent clock, let's register the mclk as a basic
clk-divider to common clock framework.  Then with it being a clock
provdier, clk_get() call in codec driver probe function will just work.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

codec->control_data has to be left unset to make the ASoC core access
the regmap properly.

That bug slipped in during a rebase session of the driver refactoring.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Replace calls to snd_soc_update_bits() with regmap_update_bits().
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

commit b047e1cc (ASoC: ac97: Support multi-platform AC'97) introduced
some build failures for modules wanting to access the generic
soc_ac97_ops.  For example:

ERROR: "soc_ac97_ops" [sound/soc/codecs/snd-soc-wm9712.ko] undefined!

To fix, export soc_ac97_ops to modules.

Cc: Mark Brown <broonie@linaro.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

commit b047e1cc (ASoC: ac97: Support multi-platform AC'97) introduced
some build failures for the pxa2xx-ac97 support, fix them.

Cc: Mark Brown <broonie@linaro.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

With the conversion to devm_ioremap_resource() the memregion variable is
no longer used so it can be dropped.
Signed-off-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

devm_ioremap_resource() already outputs an error message when any of the
operations it performs fails, so the duplicate in the caller can be
removed.
Signed-off-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NMark Brown <broonie@linaro.org>