This patch adds support for the I2C-SPI bridge which can be found on the Analog
Devices AD-FMCOMMS1-EBZ board.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use gpio_is_valid() to replace "gpio >= 0" or "gpio < 0".

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NHui Wang <jason77.wang@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The config.speed_hz is just setted at the two lines ahead of it,
obviously we don't need to copy the code to set the config.speed_hz
again. Remove it for a cleanup.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NHui Wang <jason77.wang@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The chip select line was configured as output with the initial value
being active explicitly. It was later deasserted during
spi_bitbang_setup() without any clock activity in between. So it makes
no sense to activate the device at all and the chip select line can
better start non-active.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use the dmaengine based Tegra APB DMA driver for
data transfer between SPI FIFO and memory in
place of legacy Tegra APB DMA.

The new driver is selected if legacy driver is not
selected and new DMA driver is enabled through config
file.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If we're gonna use runtime PM it's a pretty good idea to actually
enable it in probe() and disable it in remove() too, so it
gets used for real. Up until now we only fooled around with the
reference count.

Cc: Vinit Shenoy <vinit.shenoy@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This ASIC variant has been deleted from the ARM tree, no need
to keep support around.

Cc: Vinit Shenoy <vinit.shenoy@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commit ffbbdd21
"spi: create a message queueing infrastructure"
Accidentally deleted the logic to disable the port
when unused leading to higher power consumption.
Fix this up.

Cc: stable@kernel.org
Cc: Vinit Shenoy <vinit.shenoy@st.com>
Signed-off-by: NVirupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The acpi_pad driver can get stuck in destroy_power_saving_task()
waiting for kthread_stop() to stop a power_saving thread.  The problem
is that the isolated_cpus_lock mutex is owned when
destroy_power_saving_task() calls kthread_stop(), which waits for a
power_saving thread to end, and the power_saving thread tries to
acquire the isolated_cpus_lock when it calls round_robin_cpu().  This
patch fixes the issue by making round_robin_cpu() use its own mutex.

https://bugzilla.kernel.org/show_bug.cgi?id=42981

Cc: stable@vger.kernel.org
Signed-off-by: NStuart Hayes <Stuart_Hayes@Dell.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This fixes a regression in 3.4-rc1 caused by commit
ea9f8856
(ACPI video: Harden video bus adding.)

Some platforms don't have _DOS control method, but the ACPI
backlight still works.
We should not invoke _DOS for these platforms.

https://bugzilla.kernel.org/show_bug.cgi?id=43168

Cc: Igor Murzov <intergalactic.anonymous@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

In commit 7a879824 we added
a wrapper for the WDIOC_GETSTATUS ioctl call. The code results
however in a different behaviour: it returns an error if the
driver doesn't support the status operation. This is not
according to the API that says that when we don't support
the status operation, that we just should return a 0 value.
Only when the device isn't there anymore, we should return an
error.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This patch is to unregister for NMI events upon exit. Also we are now
making the default setting for allow_kdump enabled.
Signed-off-by: NThomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

The recent conversion of iTCO_wdt resulted in the driver no longer
getting loaded automatically, since it no longer has a
MODULE_DEVICE_TABLE() included. As the lpc_ich driver now creates a
platform device, auto-loading can easily be done by having a respective
module alias in place.
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This reverts commit f82cfb6b.

This breaks the backlight controls on my IVB asus zenbook with an eDP
panel.

I guess the right fix would be to read this bit and use either the pch
or the cpu register to frob the backlight values. But that is stuff
for -next.

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Commit e978aa7d ( cpuidle: Move
dev->last_residency update to driver enter routine; remove dev->last_state)
was  breaking suspend on laptops, as reported in the below link
	- https://lkml.org/lkml/2011/11/11/164

This was fixed in commit 3439a8da
(ACPI / cpuidle: Remove acpi_idle_suspend (to fix suspend regression)
by removing acpi_idle_suspend flag.
	- https://lkml.org/lkml/2011/11/14/74

But this did fix did not work on all systems
as Suspend/resume regression was reported on Lenovo S10-3
recently by Dave.
	- https://lkml.org/lkml/2012/5/27/115
It looked like with commit e978aa7d broke suspend and
with commit 3439a8da resume was not working with acpi_idle driver.

This patch fixes the regression that caused this issue
in the first place. acpi_idle_suspend flag is essential on
some x86 systems to prevent the cpus from going to deeper C-states
when suspend is triggered ( commit b04e7bdb )
So reverting the commit 3439a8da is essential.

By default, irqs are disabled in cpu_idle arch specific call
and re-enabled in idle state return path . During suspend,
the acpi_idle_suspend flag is set, which
prevents the cpus from going to deeper idle states,
it is essential to enabling the irqs in this return path too.

To address the suspend issue,
we were not re-enabling the interrupts while returning from
acpi_idle_enter_bm() routine if acpi_idle_suspend flag is set.
and this caused suspend failure.

In addition to the above, to improve the readability of the code,
return of -ENIVAL is replaced with -EBUSY in acpi_idle_suspend
return path. Implying that the system is currently busy when suspend
is in progress, which prevents the cpus from entering deeper C-states.
Reported-and-Tested-by: NDav Hansen <dave@linux.vnet.ibm.com>
Tested-by: NPreeti Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: NDeepthi Dharwar <deepthi@linux.vnet.ibm.com>
Reviewed-by: NSrivatsa S Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Commit "e9b4cf20 UBI: fix debugfs-less systems support" fixed one
regression but introduced a different regression - the debugfs is now always
compiled out. Root cause: IS_ENABLED() arguments should be used with the
CONFIG_* prefix.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

The freescale arm i.MX series platform can support this driver, and
usually the arm cpu works in the little endian mode by default, while
device tree entry value is stored in big endian format, we should use
be32_to_cpup() to handle them, after modification, it can work well
both on the le cpu and be cpu.

Cc: stable <stable@vger.kernel.org> # v3.2+
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: NHui Wang <jason77.wang@gmail.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Just forgot this when I posted it, and yes I'm the only person
to have changed the file since.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fixes:
[   15.470311] WARNING: at /local/scratch/ianc/devel/kernels/linux/fs/sysfs/file.c:498 sysfs_attr_ns+0x95/0xa0()
[   15.470326] sysfs: kobject eth0 without dirent
[   15.470333] Modules linked in:
[   15.470342] Pid: 12, comm: xenwatch Not tainted 3.4.0-x86_32p-xenU #93
and
[    9.150554] BUG: unable to handle kernel paging request at 2b359000
[    9.150577] IP: [<c1279561>] linkwatch_do_dev+0x81/0xc0
[    9.150592] *pdpt = 000000002c3c9027 *pde = 0000000000000000
[    9.150604] Oops: 0002 [#1] SMP
[    9.150613] Modules linked in:

This is http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=675190Reported-by: NGeorge Shuklin <george.shuklin@gmail.com>
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Tested-by: NWilliam Dauchy <wdauchy@gmail.com>
Cc: stable@kernel.org
Cc: 675190@bugs.debian.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some architectures address spaces are set up in a way that this is
not necessary to work properly but on some others (like s390) it is.
Make sure we operate on the user address space to allow copy_xxx_user()
from the vhost_worker() thread by setting it explicitly before calling
use_mm() and revert it after unuse_mm().
Signed-off-by: NJens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FCoE target mode was experiencing issues due to the fact that we were
sending up data frames that were padded to 60 bytes after the DDP logic had
already stripped the frame down to 52 or 56 depending on the use of VLANs.
This was resulting in the FCoE DDP logic having issues since it thought the
frame still had data in it due to the padding.

To resolve this, adding code so that we do not pad FCoE frames prior to
handling them to the stack.

CC: <stable@vger.kernel.org>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds 10 device IDs for CP210x based devices from the following manufacturers:
Timewave
Clipsal
Festo
Link Instruments
Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This device is also known as the Verizon USB551L.
Signed-off-by: NForest Bond <forest.bond@rapidrollout.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

USB phy layer driver are only built if usb host is selected, but they
are used too by USB_GADGET drivers
Signed-off-by: NAlexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch reverts the commit dba3c29e.

After bisecting, this commit dba3c29e is found to ruin micro-SD card data
(writing incorrect file, or fs is corrupt after several times mount)
on the beagle-xm revB, and reverting the commit will fix the problem.

Also from TRM of OMAP3/OMAP4/DM37x, the below is mentioned about
the Auto CMD12 Enable bit.
        - SDIO does not support this feature.
        - SD card only.
Looks it is not suitable to always enable Auto CMD12 in host controller
driver.

Considered that the commit is not mature enough, so ask to revert it
first.

Cc: Balaji T K <balajitk@ti.com>
Cc: Venkatraman S <svenkatr@ti.com>
Buglink: https://lkml.org/lkml/2012/6/10/225Reported-by: NPaolo Pisati <p.pisati@gmail.com>
Reported-bisected-and-tested-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Acked-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

If multi block write operation fails for SD card, during
error handling we send the SD_APP_SEND_NUM_WR_BLKS (ACMD22)
to know how many blocks were already programmed by card.

But mmc_sd_num_wr_blocks() function which sends the ACMD22
calculates the data timeout value from csd.tacc_ns and
csd.tacc_clks parameters which will be 0 for block addressed
(>2GB cards) SD card. This would result in timeout_ns and
timeout_clks being 0 in the mmc_request passed to host driver.
This means host controller would program its data timeout timer
value with 0 which could result in DATA TIMEOUT errors from
controller.

To fix this issue, mmc_sd_num_wr_blocks() should instead
just call the mmc_set_data_timeout() to calculate the
data timeout value. mmc_set_data_timeout() function
ensures that non zero timeout value is set even for
block addressed SD cards.
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

nv_two_heads() was never meant to be used outside of pre-nv50 code.  The
code checks for >= NV_10 for 2 CRTCs, then downgrades a few specific
chipsets to 1 CRTC based on (pci_device & 0x0ff0).

The breakage example seen is on GTX 560Ti, with a pciid of 0x1200, which
gets detected as an NV20 (0x020x) with 1 CRTC by nv_two_heads(), causing
memory corruption because there's actually 2 CRTCs..

This switches fbcon to use the CRTC count directly from the mode_config
structure, which will also fix the same issue on Kepler boards which have
4 CRTCs.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

The struct clk_lookup are marked as __initdata, resulting in being
removed from memory after the kernel finished booting. However this
leads to a NULL pointer de-ref if loading a module which uses clk_get.

This patch removes the __initdata from the struct clk_lookup.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The definition of clocks ref_io0 and ref_io1 were inverted.  It causes
a mmc regression on some boards right away.  Fix the regression by
correcting the ref_io clock definition.
Reported-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

clk_change_rate() is accessing parent's rate without checking
if the parent exists at all. In case of root clocks this will
cause NULL pointer dereference.

This patch follows what clk_calc_new_rates() does in such
situation.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>
Cc: stable@kernel.org

Parent clocks for muxes are cached in clk->parents to
avoid frequent lookups, however the cache allocation happens
only during clock registeration and later clk_set_parent()
assumes a cache space available and allocated.

This is not entirely true for platforms which do early clock
registerations wherein the cache allocation using kzalloc
could fail during clock registeration.

Allow cache allocation to happen later as part of clk_set_parent()
to help such cases and avoid crashes assuming a cache being
available.

While here also replace existing kmalloc() with kzalloc()
in the file.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>
Cc: stable@kernel.org

Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add a missing resource release in ring cleanup.
Not doing this leaves a range of QPs that are being reserved,
and no one can use them.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a crash at the error flow of NOP command which caused the driver to try and use
a completion vector which wasn't allocated.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set valid port parameters: MTU and flow control configuration when
configuring the port during HW device initialization,
prior to the net device open() being called.
Using  invalid parameters (such as all zeros)
could lead to bad firmware behavior.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for the iPad to the ipheth driver.
(product id = 0x129a)
Signed-off-by: NDavide Gerhard <rainbow@irh.it>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a missing return, causing access to freed memory.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When receiving a piggyback'ed descriptor containing an
embedded frame, but no payload, the embedded frame was
lost.
Signed-off-by: NPer Ellefsen <per.ellefsen@stericsson.com>
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It makes sense to label "Digital Thermal Sensor" as "DTS", but
unfortunately the string "dts" was already used for "Debug Store", and
/proc/cpuinfo is a user space ABI.

Therefore, rename this to "dtherm".

This conflict went into mainline via the hwmon tree without any x86
maintainer ack, and without any kind of hint in the subject.

    a4659053 x86/hwmon: fix initialization of coretemp
Reported-by: NJean Delvare <khali@linux-fr.org>
Link: http://lkml.kernel.org/r/4FE34BCB.5050305@linux.intel.com
Cc: Jan Beulich <JBeulich@suse.com>
Cc: <stable@vger.kernel.org> v2.6.36..v3.4
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

The generic HID driver is obviously not a special driver, so move it
outside of the special drivers menu. Explain the usage and make the
default follow the HID setting. This should simplify migration from
older kernels. While at it, remove the redundant HID_SUPPORT option
and modify the HID and USB_HID entries to better explain the bus
structure.
Reported-by: NJan Beulich <jbeulich@suse.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>