This device is sold as 'ThinkPad USB-C Dock Gen 2 (40AS)'.
Chipset is RTL8153 and works with r8152.
Without this, the generic cdc_ether grabs the device, and the device jam
connected networks up when the machine suspends.
Signed-off-by: NKazutoshi Noguchi <noguchi.kazutosi@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Printing the info message every time more than the max number of mac
addresses are requested generates unnecessary log spam.  Showing it only
when the hw is not already in promiscous mode is equally informative
without being annoying.
Signed-off-by: NMans Rullgard <mans@mansr.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add an error handling in aq_nic_set_multicast_list, it may not
work when hw_multicast_list_set error; and at the same time
it will remove gcc Wunused-but-set-variable warning.
Signed-off-by: NChenwandun <chenwandun@huawei.com>
Reviewed-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tx_clk, rx_clk, and tsu_clk are optional. Currently the macb driver
marks clock as not available if it receives an error when trying to get
a clock. This is wrong, because a clock controller might return
-EPROBE_DEFER if a clock is not available, but will eventually become
available.

In these cases, the driver would probe successfully but will never be
able to adjust the clocks, because the clocks were not available during
probe, but became available later.

For example, the clock controller for the ZynqMP is implemented in the
PMU firmware and the clocks are only available after the firmware driver
has been probed.

Use devm_clk_get_optional() in instead of devm_clk_get() to get the
optional clock and propagate all errors to the calling function.
Signed-off-by: NMichael Tretter <m.tretter@pengutronix.de>
Acked-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

xenvif_connect_data() calls module_put() in case of error. This is
wrong as there is no related module_get().

Remove the superfluous module_put().

Fixes: 279f438e ("xen-netback: Don't destroy the netdev until the vif is shut down")
Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NPaul Durrant <paul@xen.org>
Reviewed-by: NWei Liu <wei.liu@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the num_msi_left means the vector numbers of NIC,
but if the PF supported RoCE, it contains the vector numbers
of NIC and RoCE(Not expected).

This may cause interrupts lost in some case, because of the
NIC module used the vector resources which belongs to RoCE.

This patch adds a new variable num_nic_msi to store the vector
numbers of NIC, and adjust the default TQP numbers and rss_size
according to the value of num_nic_msi.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In mlx5_fw_fatal_reporter_dump if mlx5_crdump_collect fails the
allocated memory for cr_data must be released otherwise there will be
memory leak. To fix this, this commit changes the return instruction
into goto error handling.

Fixes: 9b1f2982 ("net/mlx5: Add support for FW fatal reporter dump")
Signed-off-by: NNavid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In mlx5_fpga_conn_create_cq if mlx5_vector2eqn fails the allocated
memory should be released.

Fixes: 537a5057 ("net/mlx5: FPGA, Add high-speed connection routines")
Signed-off-by: NNavid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The completion queue consumer index increments upon a call to
mlx5_cqwq_pop().
When dumping an error CQE, the index is already incremented.
Decrease one for the print command.

Fixes: 16cc14d8 ("net/mlx5e: Dump xmit error completions")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Once the kTLS TX resync function is called, it used to return
a binary value, for success or failure.

However, in case the TLS SKB is a retransmission of the connection
handshake, it initiates the resync flow (as the tcp seq check holds),
while regular packet handle is expected.

In this patch, we identify this case and skip the resync operation
accordingly.

Counters:
- Add a counter (tls_skip_no_sync_data) to monitor this.
- Bump the dump counters up as they are used more frequently.
- Add a missing counter descriptor declaration for tls_resync_bytes
  in sq_stats_desc.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Do not assume the crypto info is accessible during the
connection lifetime. Save a copy of it in the private
TX context.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Cipher type is checked upon connection addition.
No need to recheck it per every TX resync invocation.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

HW expects the data size in DUMP WQEs to be up to MTU.
Make sure they are in range.

We elevate the frag page refcount by 'n-1', in addition to the
one obtained in tx_sync_info_get(), having an overall of 'n'
references. We bulk increments by using a single page_ref_add()
command, to optimize perfermance.
The refcounts are released one by one, by the corresponding completions.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Before posting the context params WQEs, make sure there is enough
contiguous room for them, and fill frag edge if needed.

When posting only a nop, no need for room check, as it needs a single
WQEBB, meaning no contiguity issue.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

All references for frag pages that are obtained in tx_sync_info_get()
should be released.
Release usually occurs in the corresponding CQE of the WQE.
In error flows, not all fragments have a WQE posted for them, hence
no matching CQE will be generated.
For these pages, release the reference in the error flow.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Access the record fragments only under the TLS ctx lock.
In the resync flow, save a copy of them to be used when
preparing and posting the required DUMP WQEs.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In TX resync flow where DUMP WQEs are posted, keep a pointer to
the fragment page to unref it upon completion, instead of saving
the whole fragment.

In addition, move it the end of the arguments list in tx_fill_wi().

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

No Eth segment, so no dynamic inline headers.
The size of a Dump WQE is fixed, use constants and remove
unnecessary checks.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

A call to kTLS completion handler was missing in the TXQSQ release
flow. Add it.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Not all fields of WQE info are being written in the function,
having some leftovers from previous rounds.
Zero-memset it upon update.

Particularly, not nullifying the wi->resync_dump_frag field
will cause double free of the kTLS DUMPed frags.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Cited patch removed the assumption only in datapath.
Here we remove it also form control/cleanup flow.

Fixes: 9ab02337 ("net/mlx5e: Tx, Don't implicitly assume SKB-less wqe has one WQEBB")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

As soon as the netdev is registers, the kernel can start using the
interface. If the driver connects the MAC to the PHY after the netdev
is registered, there is a race condition where the interface can be
opened without having the PHY connected.

Change the order to close this race condition.

Fixes: 92571a1a ("lan78xx: Connect phy early")
Reported-by: NDaniel Wagner <dwagner@suse.de>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NDaniel Wagner <dwagner@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

devlink maintains packets and bytes statistics for each trap. Since
eth_type_trans() was called to set the skb's protocol, the data pointer
no longer points to the start of the packet and the bytes accounting is
off by 14 bytes.

Fix this by pushing the skb's data pointer to the start of the packet.

Fixes: b5ce611f ("mlxsw: spectrum: Add devlink-trap support")
Reported-by: NAlex Kushnarov <alexanderk@mellanox.com>
Tested-by: NAlex Kushnarov <alexanderk@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EPHY integrated into the 40nm Set-Top Box devices can falsely
detect energy when connected to a disabled peer interface. When the
peer interface is enabled the EPHY will detect and report the link
as active, but on occasion may get into a state where it is not
able to exchange data with the connected GENET MAC. This issue has
not been observed when the link parameters are auto-negotiated;
however, it has been observed with a manually configured link.

It has been empirically determined that issuing a soft reset to the
EPHY when energy is detected prevents it from getting into this bad
state.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It turns out that the "Workaround for putting the PHY in IDDQ mode"
used by the internal EPHYs on 40nm Set-Top Box chips when powering
down puts the interface to the GENET MAC in a state that can cause
subsequent MAC resets to be incomplete.

Rather than restore the forced soft reset when powering up internal
PHYs, this commit moves the invocation of phy_init_hw earlier in
the MAC initialization sequence to just before the MAC reset in the
open and resume functions. This allows the interface to be stable
and allows the MAC resets to be successful.

The bcmgenet_mii_probe() function is split in two to accommodate
this. The new function bcmgenet_mii_connect() handles the first
half of the functionality before the MAC initialization, and the
bcmgenet_mii_config() function is extended to provide the remaining
PHY configuration following the MAC initialization.

Fixes: 484bfa15 ("Revert "net: bcmgenet: Software reset EPHY after power on"")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The internal 40nm EPHYs use a "Workaround for putting the PHY in
IDDQ mode." These PHYs require a soft reset to restore functionality
after they are powered back up.

This commit defines the soft_reset function to use genphy_soft_reset
during phy_init_hw to accommodate this.

Fixes: 6e2d85ec ("net: phy: Stop with excessive soft reset")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When commit 28b2e0d2 ("net: phy: remove parameter new_link from
phy_mac_interrupt()") removed the new_link parameter it set the
phydev->link state from the MAC before invoking phy_mac_interrupt().

However, once commit 88d6272a ("net: phy: avoid unneeded MDIO
reads in genphy_read_status") was added this initialization prevents
the proper determination of the connection parameters by the function
genphy_read_status().

This commit removes that initialization to restore the proper
functionality.

Fixes: 88d6272a ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches.
Update the PHY ID and name to reflect that, as this family of switches
is commonly refered to as KSZ87xx
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the
same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs
in the micrel PHY driver, it is used even with the KSZ87xx switch. This
is wrong, since the KSZ8051 configures registers of the PHY which are
not present on the simplified KSZ87xx switch PHYs and misconfigures
other registers of the KSZ87xx switch PHYs.

Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the
KSZ87xx switch by checking the Basic Status register Bit 0, which is
read-only and indicates presence of the Extended Capability Registers.
The KSZ8051 PHY has those registers while the KSZ87xx switch does not.

This patch implements simple check for the presence of this bit for
both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct
PHY driver instance.

Fixes: 9d162ed6 ("net: phy: micrel: add support for KSZ8795")
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The KSZ driver uses one regmap per register width (8/16/32), each with
it's own lock, but accessing the same set of registers. In theory, it
is possible to create a race condition between these regmaps, although
the underlying bus (SPI or I2C) locking should assure nothing bad will
really happen and the accesses would be correct.

To make the driver do the right thing, add one single shared mutex for
all the regmaps used by the driver instead. This assures that even if
some future hardware is on a bus which does not serialize the accesses
the same way SPI or I2C does, nothing bad will happen.

Note that the status_mutex was unused and only initied, hence it was
renamed and repurposed as the regmap mutex.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The KSZ87xx driver calls mutex_init() on mutexes already inited in
ksz_common.c ksz_switch_register(). Do not do it twice, drop the
reinitialization.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The stmmac_pcs_ctrl_ane() expects a register address as
argument 1, but for some reason the mac_device_info is
being passed.

Fix the warning (and possible bug) from sparse:

drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17:    expected void [noderef] <asn:2> *ioaddr
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17:    got struct mac_device_info *hw
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Depending on when MC connects the DPNI to a MAC, Tx FQIDs may
not be available during probe time.

Read the FQIDs each time the link goes up to avoid using invalid
values. In case an error occurs or an invalid value is retrieved,
fall back to QDID-based enqueueing.

Fixes: 1fa0f68c ("dpaa2-eth: Use FQ-based DPIO enqueue API")
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IRQ for the DPNI endpoint change event, resolving the issue
when a dynamically created DPNI gets a randomly generated hw address
when the endpoint is a DPMAC object.
Signed-off-by: NFlorin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The serial state information must not be embedded into another
data structure, as this interferes with cache handling for DMA
on architectures without cache coherence..
That would result in data corruption on some architectures
Allocating it separately.

v2: fix syntax error
Signed-off-by: NOliver Neukum <oneukum@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

disable ptp_ref_clk in suspend flow, and enable it in resume flow.

Fixes: f573c0b9 ("stmmac: move stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to platform structure")
Signed-off-by: NBiao Huang <biao.huang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.

The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.

This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.

Fixes: 88d6272a ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Reviewed-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure res does not contain random value if the call to
sr_read_cmd fails for some reason.

Reported-by: syzbot+f1842130bbcfb335bac1@syzkaller.appspotmail.com
Signed-off-by: NValentin Vidic <vvidic@valentin-vidic.from.hr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RGMII_MODE_EN bit value was 0 for GENET versions 1 through 3, and
became 6 for GENET v4 and above, account for that difference.

Fixes: aa09677c ("net: bcmgenet: add MDIO routines")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NDoug Berger <opendmb@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tc_flow_parsers is not used outside of the driver, so
make it static to avoid the following sparse warning:

drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c:516:3: warning: symbol 'tc_flow_parsers' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>