Merge mt76x0_dev data structure in mt76x02_dev one and remove
duplicated code. Remove unused definition in mt76x0.h.
Moreover merge mt76x0_caldata and mt76x02_rx_freq_cal data structures.
This is a preliminary patch for rxwi unification.
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x2_dev in mt76x02_util.h and rename it in mt76x02_dev
in order to be shared between mt76x2 and mt76x0 driver
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Remove hw_atomic_mutex mutex in mt76x0_dev data structure
since mt76x0_phy_set_channel is already protected by mt76_dev
mutex while mt76x0_chip_onoff is used just at device probe or
cleanup
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Remove no longer used mac_lock spinlock and data array
in mt76x0_dev data structure
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Use shared mt76x02 utility routines for rssi tracking.
Moreover remove no longer used con_mon_lock spinlock
and following variable:
- ap_bssid
- bcn_freq_off
- bcn_phy_mode
- avg_rssi
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_rx_get_sta and mt76x02_rx_get_sta_wcid utility routines in
mt76x02-lib module since it will be used by mt76x0 driver in order to
unify rxwi parsing
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_phy_get_min_avg_rssi in mt76x02-lib module since
it will be used by mt76x0 driver in order to unify rxwi parsing
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Remove leftover configuration for legacy devices in
mt76x0_init_mac_registers routine. Moreover remove
unnecessary msleep delay
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Use mt76x02u_tx_prepare_skb routine to fill txwi in mt76x2u and
mt76x0u driver and remove duplicated code. Moreover add static
qualifier to mt76x02_mac_tx_rate_val and mt76x02_mac_fill_txwi
routines
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_mac_write_txwi in mt76x02_mac.c since it is shared between
mt76x0 and mt76x2 drivers. This is a preliminary patch to unify txwi
configuration between mt76x0 and mt76x2 drivers
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Add get_tx_txpwr_adj function pointer to mt76_driver_ops data structure
as a preliminary patch to unify txwi configuration between mt76x0 and
mt76x2 drivers since tpc is currently supported just by mt76x2 driver
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x02_tx_get_max_txpwr_adj routine in mt76x02-lib module
since now both mt76x0 and mt76x2 drivers read rate tx power gain from
rate_power data structure. Moreover remove get_max_txpwr_adj function
pointer from mt76_driver_ops data structure
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Stop mac and calibration work stopping the hw even if the
device has been removed

Fixes: b11e1969 ("mt76x0: add ieee80211_ops ops pointer to
mt76x0_alloc_device signature")
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

mt76u_alloc_queues need to be called before mt76u_mcu_init_rx
since it initializes rx_page_lock spinlock used in mt76u_buf_alloc
routine.

Fixes: b11e1969 ("mt76x0: add ieee80211_ops ops pointer to
mt76x0_alloc_device signature")
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

This is correct fix for c12128ce ("mt76: use a per rx queue page
fragment cache"). We use wrong length when we allocate segments for
MCU transmissions, which require bigger segment size than e->buf_size.

Commit 481bb043 ("mt76: usb: make rx page_frag_cache access atomic")
partially solved the problem or actually mask it by changing
mt76u_mcu_init_rx() and mt76u_alloc_queues() sequence, so e->buf_size
become non zero any longer, but still not big enough to handle MCU data.

Patch fixes memory corruption which can manifest itself as random,
not easy to reproduce crashes, during mt76 driver load or unload.

Fixes: c12128ce ("mt76: use a per rx queue page fragment cache")
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

The header guards that are #defined are different from those being
checked.  Fix this by #defining them to the correct name.

Fixes clang warnings:
drivers/net/wireless/mediatek/mt76/mt76x02_mcu.h:17:9:
warning: '__MT76x02_MCU_H' is used as a header guard here, followed
by #define of a different macro [-Wheader-guard]

drivers/net/wireless/mediatek/mt76/mt76x02_usb.h:17:9:
warning: '__MT76x02_USB_H' is used as a header guard here, followed
by #define of a different macro [-Wheader-guard]

Fixes: 905db747 ("mt76: usb: move mt76x02 mcu code in mt76x02-usb module")
Fixes: edaa580b ("mt76: move shared mcu_calibrate routine in mt76x02-lib module")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Move mt76x2 and mt76x2u drivers to mt76x2 subfolder and
leave just shared code in mt76 root folder
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Add mt76x0e_cleanup routine to tidy up the device
during device removal
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>

Current implementation of dump_station cfg80211 callback supports
AP mode only. Add support for STA mode as well: by default in STA
mode this callback is supposed to return AP on managed interface.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Command responses and events from the firmware are copied twice in
control path: at first in shm core (qtnf_shm_handle_new_data) and
then in pcie bus drivers (qtnf_pcie_control_rx_callback). There
is no need to copy this data twice, it can be done only once
in rx callbacks.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Firmware supports scan dwell time tuning for various types of scans.
Enable support for this feature:
- advertise capability to configure channel dwell time to host
- pass scan dwell parameters to wireless card in scan request
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Notify firmware to flush cache before scanning when needed.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On disconnect wireless core attempts to remove all the supported keys.
Following cfg80211_ops conventions, firmware returns -ENOENT code
for the out-of-bound key indexes. This is a normal behavior,
so no need to report errors for this case.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Driver retrieves information about supported extended capabilities
from wireless card. However this information is not propagated
further to Linux wireless core. Fix this by setting extended
capabilities fields of wiphy structure.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

SGI should be passed to wireless core as a part of rate structure.
Otherwise wireless core performs incorrect rate calculation when
SGI is enabled in hardware but not reported to host.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Do not cancel scan in disconnect callback. If there is an active scan,
it will be cancelled by firmware, then host driver will be properly
notified by event.

Cancelling scan in disconnect callback occasionally may lead to the
following race issue. Host is able to queue one scan after scan
abort in disconnect callback, and another scan after scan abort
in event handler. As a result, firmware receives second scan
before the first scan completes.
Signed-off-by: NIgor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Unify command error handling using qtnf_cmd_resp_result_decode
function. Do not duplicate error messages in command handlers
and cfg80211 callbacks: report 'cmd exec fail' only on control
path internal failure. Remove redundant 'unlikely' macros.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Several members of pwr-MAC structure are re-initialized several times
together with per-VIF initialization. Fix that and simplify the code.
Signed-off-by: NIgor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In case firmware reports that it can not do OBSS scanning for 40MHz
2.4GHz channels itself, tell userpsace to do that instead by setting
NL80211_FEATURE_NEED_OBSS_SCAN flag.
Signed-off-by: NIgor mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When cfg80211 disconnect callback is triggered and command is
processed by firmware, disconnect event with local parameter
set must be sent immediately. Indicating that it's a "local"
event (not from AP) will help upper layers to process this
event correctly.
Signed-off-by: NIgor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Remove STA connection states tracking from driver.
Leave it wireless core on host and to firmware.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/wireless/broadcom/b43/main.c: In function 'b43_one_core_detach':
drivers/net/wireless/broadcom/b43/main.c:5496:17: warning:
 variable 'wl' set but not used [-Wunused-but-set-variable]

After commit 644aa4d6 ("b43: remove list of IEEE 802.11 devices")
'wl' is not used any more.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Replace "Fallthough" with a proper "fall through" annotation.

This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NMichael Buesch <m@bues.ch>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

lockdep_assert_held() is better suited to checking locking requirements,
since it won't get confused when someone else holds the lock. This is
also a step towards possibly removing spin_is_locked().
Signed-off-by: NLance Roy <ldr709@gmail.com>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <linux-wireless@vger.kernel.org>
Cc: <netdev@vger.kernel.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Now with wlcore using PM runtime, we can also add support for Linux
generic wakeirq handling for it if configured in the dts file.

The wakeirq can be configured as the second interrupt in the dts file
with interrupts-extended property where it is the padconf irq of the OOB
GPIO pin used for wlcore interrupt.

Note that eventually we should also allow configuring wlcore to use the
SDIO dat1 IRQ for wake-up, and in that case the the wakeirq should be
configured to be the padconf interrupt of the dat1 pin and not the
padconf interrupt of the OOB GPIO pin.

Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We do not currently clear wl->elp_compl on ELP timeout and we have bogus
lingering pointer that wlcore_irq then will try to access after recovery
is done:

BUG: spinlock bad magic on CPU#1, irq/255-wl12xx/580
...
(spin_dump) from [<c01b9344>] (do_raw_spin_lock+0xc8/0x124)
(do_raw_spin_lock) from [<c09b3970>] (_raw_spin_lock_irqsave+0x68/0x74)
(_raw_spin_lock_irqsave) from [<c01a02f0>] (complete+0x24/0x58)
(complete) from [<bf572610>] (wlcore_irq+0x48/0x17c [wlcore])
(wlcore_irq [wlcore]) from [<c01c5efc>] (irq_thread_fn+0x2c/0x64)
(irq_thread_fn) from [<c01c623c>] (irq_thread+0x148/0x290)
(irq_thread) from [<c016b4b0>] (kthread+0x160/0x17c)
(kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
...

After that the system will hang. Let's fix this by adding a flag for
recovery and moving the recovery work call to to the error handling
section.

And we want to set WL1271_FLAG_INTENDED_FW_RECOVERY and actually clear
it too in wl1271_recovery_work() and just downgrade the error to a
warning to prevent overly verbose output.

Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The following:
 bool efuse_re_pg_sec1flag;
 u8 efuse_re_pg_data[8];
are not referenced anywhere in the rtlwifi code.

This patch is originally created by Rick Veens <rickveens92@gmail.com>,
and Joe Perches <joe@perches.com> reminded to apply it to rtlwifi.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The driver sends an action frame down and waits for a completion signal
triggered by the received BRCMF_E_ACTION_FRAME_OFF_CHAN_COMPLETE event
to continue the process. However, the action frame could be transmitted
either on the current channel or on an off channel. For the on-channel
case, only BRCMF_E_ACTION_FRAME_COMPLETE event will be received when
the frame is transmitted, which make the driver always wait a full
timeout duration. This patch has the completion signal be triggered by
receiving the BRCMF_E_ACTION_FRAME_COMPLETE event for the on-channel
case.

This change fixes WFA p2p certification 5.1.19 failure.
Signed-off-by: NChung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Finding a common channel to send an action frame out is required for
some action types. Since a loop with several scan retry is used to find
the channel, a short wait time could be considered for each attempt.
This patch reduces the wait time from 1500 to 450 msec for each action
frame scan.

This patch fixes the WFA p2p certification 5.1.20 failure caused by the
long action frame send time.
Signed-off-by: NChung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

mt76 patches for 4.20

* unify code between mt76x0, mt76x2
* mt76x0 fixes
* tx power configuration fix for 76x2
* more progress on mt76x0e support
* support for getting firmware version via ethtool
* fix for rx buffer allocation regression on usb
* fix for handling powersave responses
* fix for mt76x2 beacon transmission