Some controllers have a controller-side memory buffer available for use
for submissions, completions, lists, or data.

If a CMB is available, the entire CMB will be ioremapped and it will
attempt to map the IO SQes onto the CMB. The queues will be shrunk as
needed. The CMB will not be used if the queue depth is shrunk below some
threshold where it may have reduced performance over a larger queue
in system memory.
Signed-off-by: NJon Derrick <jonathan.derrick@intel.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Lots of devices support huge discard sizes these days. Depending
on how the device handles them internally, huge discards can
introduce massive latencies (hundreds of msec) on the device side.

We have a sysfs file, discard_max_bytes, that advertises the max
hardware supported discard size. Make this writeable, and split
the settings into a soft and hard limit. This can be set from
'discard_granularity' and up to the hardware limit.

Add a new sysfs file, 'discard_max_hw_bytes', that shows the hw
set limit.
Reviewed-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Percpu refcount is the perfect match for partition's case,
and the conversion is quite straight.

With the convertion, one pair of atomic inc/dec can be saved
for accounting block I/O, which is run in hot path of block I/O.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJens Axboe <axboe@fb.com>

So the helper can be used in both generic partition
case and part0 case.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

We might return res which is not initialized. Also
reduce code duplication by exporting srp_parse_tmo so
srp_tmo_set can reuse it.

Detected by Coverity.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NJenny Falkovich <jennyf@mellanox.com>
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Persuant to Liran's comments on node_type on linux-rdma
mailing list:

In an effort to reform the RDMA core and ULPs to minimize use of
node_type in struct ib_device, an additional bit is added to
struct ib_device for is_switch (IB switch). This is needed
to be initialized by any IB switch device driver. This is a
NEW requirement on such device drivers which are all
"out of tree".

In addition, an ib_switch helper was added to ib_verbs.h
based on the is_switch device bit rather than node_type
(although those should be consistent).

The RDMA core (MAD, SMI, agent, sa_query, multicast, sysfs)
as well as (IPoIB and SRP) ULPs are updated where
appropriate to use this new helper. In some cases,
the helper is now used under the covers of using
rdma_[start end]_port rather than the open coding
previously used.
Reviewed-by: NSean Hefty <sean.hefty@intel.com>
Reviewed-By: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Tested-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NHal Rosenstock <hal@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

They just call file_inode and then the corresponding *_inode_file_wait
function. Just make them static inlines instead.
Signed-off-by: NJeff Layton <jeff.layton@primarydata.com>

Allow callers to pass in an inode instead of a filp.
Signed-off-by: NJeff Layton <jeff.layton@primarydata.com>
Reviewed-by: N"J. Bruce Fields" <bfields@fieldses.org>
Tested-by: N"J. Bruce Fields" <bfields@fieldses.org>

Commit 514ac99c "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.

Without timestamping to be required by user space applications this timestamp
was not generated which lead to commit 36c01245 "can: fix loss of CAN frames
in raw_rcv" - which forces the timestamp to be set in all CAN related skbuffs
by introducing several __net_timestamp() calls.

This forces e.g. out of tree drivers which are not using alloc_can{,fd}_skb()
to add __net_timestamp() after skbuff creation to prevent the frame loss fixed
in mainline Linux.

This patch removes the timestamp dependency and uses an atomic counter to
create an unique identifier together with the skbuff pointer.

Btw: the new skbcnt element introduced in struct can_skb_priv has to be
initialized with zero in out-of-tree drivers which are not using
alloc_can{,fd}_skb() too.
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

If there are no assigned devices, the guest PAT are not providing
any useful information and can be overridden to writeback; VMX
always does this because it has the "IPAT" bit in its extended
page table entries, but SVM does not have anything similar.
Hook into VFIO and legacy device assignment so that they
provide this information to KVM.
Reviewed-by: NAlex Williamson <alex.williamson@redhat.com>
Tested-by: NJoerg Roedel <jroedel@suse.de>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

NCM specs are not actually mandating a specific position in the frame for
the NDP (Network Datagram Pointer). However, some Huawei devices will
ignore our aggregates if it is not placed after the datagrams it points
to. Add support for doing just this, in a per-device configurable way.
While at it, update NCM subdrivers, disabling this functionality in all of
them, except in huawei_cdc_ncm where it is enabled instead.
We aren't making any distinction between different Huawei NCM devices,
based on what the vendor driver does. Standard NCM devices are left
unaffected: if they are compliant, they should be always usable, still
stay on the safe side.

This change has been tested and working with a Huawei E3131 device (which
works regardless of NDP position), a Huawei E3531 (also working both
ways) and an E3372 (which mandates NDP to be after indexed datagrams).

V1->V2:
- corrected wrong NDP acronym definition
- fixed possible NULL pointer dereference
- patch cleanup
V2->V3:
- Properly account for the NDP size when writing new packets to SKB
Signed-off-by: NEnrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

e48453c3 ("block, cgroup: implement policy-specific per-blkcg
data") updated per-blkcg policy data to be dynamically allocated.
When a policy is registered, its policy data aren't created.  Instead,
when the policy is activated on a queue, the policy data are allocated
if there are blkg's (blkcg_gq's) which are attached to a given blkcg.
This is buggy.  Consider the following scenario.

1. A blkcg is created.  No blkg's attached yet.

2. The policy is registered.  No policy data is allocated.

3. The policy is activated on a queue.  As the above blkcg doesn't
   have any blkg's, it won't allocate the matching blkcg_policy_data.

4. An IO is issued from the blkcg and blkg is created and the blkcg
   still doesn't have the matching policy data allocated.

With cfq-iosched, this leads to an oops.

It also doesn't free policy data on policy unregistration assuming
that freeing of all policy data on blkcg destruction should take care
of it; however, this also is incorrect.

1. A blkcg has policy data.

2. The policy gets unregistered but the policy data remains.

3. Another policy gets registered on the same slot.

4. Later, the new policy tries to allocate policy data on the previous
   blkcg but the slot is already occupied and gets skipped.  The
   policy ends up operating on the policy data of the previous policy.

There's no reason to manage blkcg_policy_data lazily.  The reason we
do lazy allocation of blkg's is that the number of all possible blkg's
is the product of cgroups and block devices which can reach a
surprising level.  blkcg_policy_data is contrained by the number of
cgroups and shouldn't be a problem.

This patch makes blkcg_policy_data to be allocated for all existing
blkcg's on policy registration and freed on unregistration and removes
blkcg_policy_data handling from policy [de]activation paths.  This
makes that blkcg_policy_data are created and removed with the policy
they belong to and fixes the above described problems.
Signed-off-by: NTejun Heo <tj@kernel.org>
Fixes: e48453c3 ("block, cgroup: implement policy-specific per-blkcg data")
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Add all_blkcgs list goes through blkcg->all_blkcgs_node and is
protected by blkcg_pol_mutex.  This will be used to fix
blkcg_policy_data allocation bug.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Grab a reference on a network namespace of the 'rbd map' (in case of
rbd) or 'mount' (in case of ceph) process and use that to open sockets
instead of always using init_net and bailing if network namespace is
anything but init_net.  Be careful to not share struct ceph_client
instances between different namespaces and don't add any code in the
!CONFIG_NET_NS case.

This is based on a patch from Hong Zhiguo <zhiguohong@tencent.com>.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Reviewed-by: NSage Weil <sage@redhat.com>

All users gone. Remove it before we get another one.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

This kernel patch exports the value of the new
ignore_routes_with_linkdown via netconf.

v2: changes to notify userspace via netlink when sysctl values change
and proposed for 'net' since this could be considered a bugfix
Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Suggested-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a cpu goes up some architectures (e.g. x86) have to walk the irq
space to set up the vector space for the cpu. While this needs extra
protection at the architecture level we can avoid a few race
conditions by preventing the concurrent allocation/free of irq
descriptors and the associated data.

When a cpu goes down it moves the interrupts which are targeted to
this cpu away by reassigning the affinities. While this happens
interrupts can be allocated and freed, which opens a can of race
conditions in the code which reassignes the affinities because
interrupt descriptors might be freed underneath.

Example:

CPU1				CPU2
cpu_up/down
 irq_desc = irq_to_desc(irq);
				remove_from_radix_tree(desc);
 raw_spin_lock(&desc->lock);
				free(desc);

We could protect the irq descriptors with RCU, but that would require
a full tree change of all accesses to interrupt descriptors. But
fortunately these kind of race conditions are rather limited to a few
things like cpu hotplug. The normal setup/teardown is very well
serialized. So the simpler and obvious solution is:

Prevent allocation and freeing of interrupt descriptors accross cpu
hotplug.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPeter Zijlstra <peterz@infradead.org>
Cc: xiao jin <jin.xiao@intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Link: http://lkml.kernel.org/r/20150705171102.063519515@linutronix.de

Making tick_broadcast_oneshot_control() independent from
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST broke the build for
CONFIG_GENERIC_CLOCKEVENTS=n because the function is not defined
there.

Provide a proper stub inline.

Fixes: f32dd117 'tick/broadcast: Make idle check independent from mode and config'
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Currently the broadcast busy check, which prevents the idle code from
going into deep idle, works only in one shot mode.

If NOHZ and HIGHRES are off (config or command line) there is no
sanity check at all, so under certain conditions cpus are allowed to
go into deep idle, where the local timer stops, and are not woken up
again because there is no broadcast timer installed or a hrtimer based
broadcast device is not evaluated.

Move tick_broadcast_oneshot_control() into the common code and provide
proper subfunctions for the various config combinations.

The common check in tick_broadcast_oneshot_control() is for the C3STOP
misfeature flag of the local clock event device. If its not set, idle
can proceed. If set, further checks are necessary.

Provide checks for the trivial cases:

 - If broadcast is disabled in the config, then return busy

 - If oneshot mode (NOHZ/HIGHES) is disabled in the config, return
   busy if the broadcast device is hrtimer based.

 - If oneshot mode is enabled in the config call the original
   tick_broadcast_oneshot_control() function. That function needs
   extra checks which will be implemented in seperate patches.

[ Split out from a larger combo patch ]
Reported-and-tested-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Suzuki Poulose <Suzuki.Poulose@arm.com>
Cc: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com>
Cc: Catalin Marinas <Catalin.Marinas@arm.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1507070929360.3916@nanos

Device drivers typically use ACPI _HIDs/_CIDs listed in struct device_driver
acpi_match_table to match devices. However, for generic drivers, we do not
want to list _HID for all supported devices. Also, certain classes of devices
do not have _CID (e.g. SATA, USB). Instead, we can leverage ACPI _CLS,
which specifies PCI-defined class code (i.e. base-class, subclass and
programming interface). This patch adds support for matching ACPI devices using
the _CLS method.

To support loadable module, current design uses _HID or _CID to match device's
modalias. With the new way of matching with _CLS this would requires modification
to the current ACPI modalias key to include _CLS. This patch appends PCI-defined
class-code to the existing ACPI modalias as following.

    acpi:<HID>:<CID1>:<CID2>:..:<CIDn>:<bbsspp>:
E.g:
    # cat /sys/devices/platform/AMDI0600:00/modalias
    acpi:AMDI0600:010601:

where bb is th base-class code, ss is te sub-class code, and pp is the
programming interface code

Since there would not be _HID/_CID in the ACPI matching table of the driver,
this patch adds a field to acpi_device_id to specify the matching _CLS.

    static const struct acpi_device_id ahci_acpi_match[] = {
        { ACPI_DEVICE_CLASS(PCI_CLASS_STORAGE_SATA_AHCI, 0xffffff) },
        {},
    };

In this case, the corresponded entry in modules.alias file would be:

    alias acpi*:010601:* ahci_platform
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NHanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: NSuravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This effectively reverts the following three commits:

 7bc10388 ACPI / resources: free memory on error in add_region_before()
 0f1b414d ACPI / PNP: Avoid conflicting resource reservations
 b9a5e5e1 ACPI / init: Fix the ordering of acpi_reserve_resources()

(commit b9a5e5e1 introduced regressions some of which, but not
all, were addressed by commit 0f1b414d and commit 7bc10388
was a fixup on top of the latter) and causes ACPI fixed hardware
resources to be reserved at the fs_initcall_sync stage of system
initialization.

The story is as follows.  First, a boot regression was reported due
to an apparent resource reservation ordering change after a commit
that shouldn't lead to such changes.  Investigation led to the
conclusion that the problem happened because acpi_reserve_resources()
was executed at the device_initcall() stage of system initialization
which wasn't strictly ordered with respect to driver initialization
(and with respect to the initialization of the pcieport driver in
particular), so a random change causing the device initcalls to be
run in a different order might break things.

The response to that was to attempt to run acpi_reserve_resources()
as soon as we knew that ACPI would be in use (commit b9a5e5e1).
However, that turned out to be too early, because it caused resource
reservations made by the PNP system driver to fail on at least one
system and that failure was addressed by commit 0f1b414d.

That fix still turned out to be insufficient, though, because
calling acpi_reserve_resources() before the fs_initcall stage of
system initialization caused a boot regression to happen on the
eCAFE EC-800-H20G/S netbook.  That meant that we only could call
acpi_reserve_resources() at the fs_initcall initialization stage
or later, but then we might just as well call it after the PNP
initalization in which case commit 0f1b414d wouldn't be
necessary any more.

For this reason, the changes made by commit 0f1b414d are reverted
(along with a memory leak fixup on top of that commit), the changes
made by commit b9a5e5e1 that went too far are reverted too and
acpi_reserve_resources() is changed into fs_initcall_sync, which
will cause it to be executed after the PNP subsystem initialization
(which is an fs_initcall) and before device initcalls (including
the pcieport driver initialization) which should avoid the initial
issue.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=100581
Link: http://marc.info/?t=143092384600002&r=1&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99831
Link: http://marc.info/?t=143389402600001&r=1&w=2
Fixes: b9a5e5e1 "ACPI / init: Fix the ordering of acpi_reserve_resources()"
Reported-by: NRoland Dreier <roland@purestorage.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Modular users will always be users of init functionality, but
users of init functionality are not necessarily always modules.

Hence any functionality like module_init and module_exit would
be more at home in the module.h file.  And module.h should
explicitly include init.h to make the dependency clear.

We've already done all the legwork needed to ensure that this
move does not cause any build regressions due to implicit
header file include assumptions about where module_init lives.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Change ntb_hw_intel to use the new NTB hardware abstraction layer.

Split ntb_transport into its own driver.  Change it to use the new NTB
hardware abstraction layer.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Abstract the NTB device behind a programming interface, so that it can
support different hardware and client drivers.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Currently print_cfs_rq() is declared in include/linux/sched.h.
However it's not used outside kernel/sched. Hence move the
declaration to kernel/sched/sched.h

Also some functions are only available for CONFIG_SCHED_DEBUG=y.
Hence move the declarations to within the #ifdef.
Signed-off-by: NSrikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: NRik van Riel <riel@redhat.com>
Cc: Iulia Manda <iulia.manda21@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1435252903-1081-2-git-send-email-srikar@linux.vnet.ibm.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Both CONFIG_SCHEDSTATS=y and CONFIG_TASK_DELAY_ACCT=y track task
sched_info, which results in ugly #if clauses.

Simplify the code by introducing a synthethic CONFIG_SCHED_INFO
switch, selected by both.
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: a.p.zijlstra@chello.nl
Cc: ricklind@us.ibm.com
Link: http://lkml.kernel.org/r/8d19eef800811a94b0f91bcbeb27430a884d7433.1435255405.git.naveen.n.rao@linux.vnet.ibm.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Commit 1cde2930 ("sched/preempt: Add static_key() to preempt_notifiers")
had two problems.  First, the preempt-notifier API needs to sleep with the
addition of the static_key, we do however need to hold off preemption
while modifying the preempt notifier list, otherwise a preemption could
observe an inconsistent list state.  KVM correctly registers and
unregisters preempt notifiers with preemption disabled, so the sleep
caused dmesg splats.

Second, KVM registers and unregisters preemption notifiers very often
(in vcpu_load/vcpu_put).  With a single uniprocessor guest the static key
would move between 0 and 1 continuously, hitting the slow path on every
userspace exit.

To fix this, wrap the static_key inc/dec in a new API, and call it from
KVM.

Fixes: 1cde2930 ("sched/preempt: Add static_key() to preempt_notifiers")
Reported-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Reported-by: NTakashi Iwai <tiwai@suse.de>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

At the moment the IRQCHIP_DECLARE macro is only declared locally in
drivers/irqchip/irqchip.h. It prevents from using it directly in arch/*
directories whenever irqchip drivers only exist there, which happens in a few
cases (e.g. arc, arm, microblaze and mips).

This patch makes the macro to be globally defined, i.e. in
include/linux/irqchip.h, and thus usable for arch-specific declarations of
irqchip drivers. In this way, it is very similar to what clocksource does (ie
CLOCKSOURCE_OF_DECLARE is defined in include/linux/clocksource.h).

For now, this patch only moves the declaration of the macro
IRQCHIP_DECLARE to the global header 'include/linux/irqchip.h' and make
'drivers/irqchip/irqchip.h' include 'include/linux/irqchip.h'. Later, other
patches will get rid of 'drivers/irqchip/irqchip.h' and modify all the impacted
irqchip drivers.
Signed-off-by: NJoel Porquet <joel@porquet.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1435865565-14114-1-git-send-email-joel@porquet.orgSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

52ebea74 ("writeback: make backing_dev_info host cgroup-specific
bdi_writebacks") made bdi (backing_dev_info) host per-cgroup wb's
(bdi_writeback's).  As the congested state needs to be per-wb and
referenced from blkcg side and multiple wbs, the patch made all
non-root cong's (bdi_writeback_congested's) reference counted and
indexed on bdi.

When a bdi is destroyed, cgwb_bdi_destroy() tries to drain all
non-root cong's; however, this can hang indefinitely because wb's can
also be referenced from blkcg_gq's which are destroyed after bdi
destruction is complete.

To fix the bug, bdi destruction will be updated to not wait for cong's
to drain, which naturally means that cong's may outlive the associated
bdi.  This is fine for non-root cong's but is problematic for the root
cong's which are embedded in their bdi's as they may end up getting
dereferenced after the containing bdi's are freed.

This patch makes root cong's behave the same as non-root cong's.  They
are no longer embedded in their bdi's but allocated separately during
bdi initialization, indexed and reference counted the same way.

* As cong handling is the same for all wb's, wb->congested
  initialization is moved into wb_init().

* When !CONFIG_CGROUP_WRITEBACK, there was no indexing or refcnting.
  bdi->wb_congested is now a pointer pointing to the root cong
  allocated during bdi init and minimal refcnting operations are
  implemented.

* The above makes root wb init paths diverge depending on
  CONFIG_CGROUP_WRITEBACK.  root wb init is moved to cgwb_bdi_init().

This patch in itself shouldn't cause any consequential behavior
differences but prepares for the actual fix.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NJon Christopherson <jon@jons.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100681Tested-by: NJon Christopherson <jon@jons.org>

Added <linux/slab.h> include to backing-dev.h for kfree() definition.
Signed-off-by: NJens Axboe <axboe@fb.com>

This patch only moves files to their new locations, before applying the
next two patches adding the NTB Abstraction layer.  Splitting this patch
from the next is intended make distinct which code is changed only due
to moving the files, versus which are substantial code changes in adding
the NTB Abstraction layer.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

sb_getblk() is used during ext4 (and possibly other FSes) writeback
paths. Sometimes such path require allocating memory and guaranteeing
that such allocation won't block. Currently, however, there is no way
to provide user flags for sb_getblk which could lead to deadlocks.

This patch implements a sb_getblk_gfp with the only difference it can
accept user-provided GFP flags.
Signed-off-by: NNikolay Borisov <kernel@kyup.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org

ACPICA commit 2fcf4f4c95e6a4875f39a929f8f92ef50cc53bb5
ACPICA commit d7a940bb308d001b5d2b196174fee36c7daa61d6

Version 20150619.

Link: https://github.com/acpica/acpica/commit/2fcf4f4c
Link: https://github.com/acpica/acpica/commit/d7a940bbSigned-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA commit 254bf77e7ca01cb27e026fa5737f7df8dae03f2c

- Add constans for the start_method.
- Remove the control structure, not part of ACPI, not defined in the current
TCG spec.

Link: https://github.com/acpica/acpica/commit/254bf77eReported-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA commit 33140b4498666337dd33a00cf3c4797a53981a7b

Changes for a new version of the 3rd party spec for these tables,
the "TCG ACPI Specification", December 14, 2014. Also, moved the
definition of TPM2 to actbl2.h, next to TCPA, since both should
be together.

Update the table compiler/disassembler code for the tables.
However, the "Server" TCPA table is not supported at this time.

Link: https://github.com/acpica/acpica/commit/33140b44Reported-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA commit 3b1026e0bdd3c32eb6d5d313f3ba0b1fee7597b4
ACPICA commit 00f0dc83f5cfca53b27a3213ae0d7719b88c2d6b
ACPICA commit 47d22a738d0e19fd241ffe4e3e9d4e198e4afc69

Across all of ACPICA. Replace C library macros such as ACPI_STRLEN with the
standard names such as strlen. The original purpose for these macros is
long since obsolete.
Also cast various invocations as necessary. Bob Moore, Jung-uk Kim, Lv Zheng.

Link: https://github.com/acpica/acpica/commit/3b1026e0
Link: https://github.com/acpica/acpica/commit/00f0dc83
Link: https://github.com/acpica/acpica/commit/47d22a73Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NJung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA commit c0ce529e1fbb8ec47d2522a3aa10f3ab77e16e41

There is no reference counting implemented for struct acpi_namespace_node, so it
is currently not removable during runtime.
This patch changes the namespace override code to keep the old
struct acpi_namespace_node undeleted so that the override mechanism can happen
during runtime. Bob Moore.

Link: https://github.com/acpica/acpica/commit/c0ce529eSigned-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA commit 27415c82fcecf467446f66d1007a0691cc5f3709

This patch adds OSDT (Override System Definition Table) support.
When OSDT is loaded, conflict namespace objects will be overridden
by the AML interpreter. Bob Moore, Lv Zheng.

Link: https://github.com/acpica/acpica/commit/27415c82Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA commit 4b100dc43e8baee8c8b4891b23bc7ad03eba6a28

Support for the new version field in the generic distributor
subtable. Hanjun Guo <hanjun.guo@linaro.org>

Link: https://github.com/acpica/acpica/commit/4b100dc4Signed-off-by: NHanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA commit 9a2b638acb3a7215209432e070c6bd0312374229

ACPI Device object often contains a _CLS object to supply PCI-defined class
code for the device. This patch introduces logic to process the _CLS
object. Suravee Suthikulpanit, Lv Zheng.

Link: https://github.com/acpica/acpica/commit/9a2b638aAcked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NHanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: NSuravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA commit 5d00e67a74542d030f0a55e7a947a020ef0d9693

This patch copies EFI interface definitions to the ACPICA code base so that
the EFI utility support can be ported to other EFI implementation.

Known issues:
1. MS Builds of uefi_call_wrapper()
   The uefi_call_wrapper() in GNU EFI is implemented in a the way to work
   around the ABI difference between Unix and MS. While I don't have
   environment to test the MS builds.

In order to port the ACPICA utilities to other EFI implementation, all that
need to be done is to impelement the 64-bit division support and the
program entry point where the efi_main() is invoked. Code to impelement
these is platform specific, and ACPICA currently choose to hide such
platform specific code within the specific EFI impelementation. Lv Zheng.

This patch doesn't affect Linux kernel.

Link: https://github.com/acpica/acpica/commit/5d00e67aSigned-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>