Just checking the code in cs42l51_fill_cache():
The cache pointer points to codec->reg_cache + 1.
I think it is because CS42L51_FIRSTREG is 0x01,
so codec->reg_cache[0] is not used here.

Then we read CS42L51_NUMREGS bytes to cache.
So we need reg_cache_size to be CS42L51_NUMREGS + 1.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Replace the manual register restore mechanism in cs4270.c and call the
generic snd_soc_cache_sync() handler instead.

This factors code out in favour of core facilities and also fixes a
bus confusion that is most probably caused by intermixing i2c-regmap
functions and i2c_smbus_* accessors.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Reported-and-tested-by: NSven Neumann <s.neumann@raumfeld.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In the case of ((max9877_regs[reg] >> shift) & mask) != val
but ((max9877_regs[reg2] >> shift) & mask) == val2,
current code does not update the registers.

Fix the logic to update registers if either val or val2 is changed.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet:
The BIT[5:4] of ADC Control Register 2 is to control the word width.
        00 = 25 Bits
        01 = 20 Bits
        10 = 16 Bits
        11 = Invalid

Thus, the AD1836_ADC_WORD_OFFSET should be defined as 4.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NAlexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the arrays.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the arrays.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
the last entry from being omitted.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

This patch makes it possible to set DAI mode to its currently applied
value even if codec is active. This is necessary to allow

aplay -t raw -r 44100 -f S16_LE -c 2 < /dev/urandom &
alsactl store -f backup.state
alsactl restore -f backup.state

to work without returning errors. This patch is based on a patch sent
by Klaus Kurzmann <mok@fluxnetz.de>.
Signed-off-by: NTimo Juhani Lindfors <timo.lindfors@iki.fi>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

The coefficient RAM must be saved in a shadow so it can
be restored when the codec is powered on using
regulator_bulk_enable().
Signed-off-by: NJohannes Stezenbach <js@sig21.net>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

WM9081_BIAS_ENA is the bit[1] of WM9081_BIAS_CONTROL_1 register (05h).
Current code incorrectly write it to WM9081_VMID_CONTROL(04h) register.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

VMID Divider Enable and Select is controlled by BIT[2:1] of WM9081_VMID_CONTROL
register (04h).
Current code reads wrong register (WM9081_BIAS_CONTROL_1) for setting
VMID 2*240k.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Occasionally we may see an accessory reported before we have a stable
impedance for the accessory. If this happens then reread the status in
order to ensure that the handler can take the appropriate action for the
status change.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The field is no longer initialised so this will crash if running on
wm8958.
Reported-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The field is no longer initialised so this will crash if running on
wm8958.
Reported-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Since there is no current software control for these they would otherwise
be left enabled, consuming power.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The WM8962 has a separate software reset for the PLL registers. Ensure that
these are reset also on startup.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up.  So
fix up those users now.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Set `invert' bit for Capture Switch. Otherwise analogue is muted when
Capture Switch is ON.
Signed-off-by: NHong Xu <hong.xu@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Current implementation in wm8711_set_dai_fmt always clear BIT[3:2]
(the Input Audio Data Bit Length Select) of WM8711_IFACE(07h) register.
Input Audio Data Bit Length Select bits are set by wm8711_hw_params,
we should leave BIT[3:2] untouched in wm8711_set_dai_fmt.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The Input Audio Data Bit Length Select is controlled by BIT[3:2] of
WM8711_IFACE(07h) register.
Current code incorrectly masks BIT[1:0] which is for Audio Data Format Select.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

According to the datasheet:

Page0 / Register8: Audio Serial Data interface Control Register A
BIT 7: Bit Clock Directional Control
        0: Bit clock is an input (slave mode)
        1: Bit clock is an output (master mode)

BIT 6: Word Clock Directional Control
        0: Word clock is an input (slave mode)
        1: Word clock is an output (master mode)

Current code sets BIT_CLK_MASTER and WORD_CLK_MASTER bits for master mode,
but does not clear these bits for slave mode.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet:

Digital Audio Interface Format (07h) register:
BIT6:	Master/slave mode
	0: Slave
	1: Master

Current code sets TLV320AIC23_MS_MASTER bit for master mode,
but does not clear it for slave mode.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet:
BCLK is controlled by BIT[4:2] of WM8940_CLOCK(06h) register.
Signed-off-by: NChris Paulson-Ellis <chris@edesix.com>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reported-by: NChris Paulson-Ellis <chris@edesix.com>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

codec->hw_write is broken now, convert codec->hw_write to snd_soc_write.

The hardware has 2 banks of registers sharing a section in I2C register space.
The 1st bank is the primary one and is cached.
The 2nd bank is for loading coefficients only and they do not need cache.
These coefficients registers are therefore direct writes.
Thus we set cache_bypass flag to deal with this before calling snd_soc_write.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Ensure all mask bits are clear before setting new value.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NDong Aisheng <b29396@freescale.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

DA7210 has three line outputs. OUT1 Left, OUT1 Right and OUT2 (mono).
This patch adds support for gain controls for these three line outs.
It also adds support for overall DAC gain control.
Signed-off-by: NAshish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds support for DAPM covering all inputs and outputs
as well as ADC and DAC.
Signed-off-by: NAshish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We have defined SGTL5000_LINREG_VDDD_MASK in sgtl5000.h,
use it instead of hardcoded (0x1 << 4) - 1 for the mask.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Otherwise calling ldo_regulator_remove() does not unregister regulator
and free memories.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org