The watchdog mask bit offset listed for Exynos7 is incorrect.
Fix this.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Naveen Krishna Chatradhi <naveenkrishna.ch@gmail.com
Reviewd-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
Signed-off-by: NVishnu Motghare <vishnum@xilinx.com>
Signed-off-by: NHarini Katakam <harinik@xilinx.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]

Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).

For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:

S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->

The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.

Hence, fix it by generating Stop condition (STP) always when NACK is received.

This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a ("i2c: omap: query STP always when NACK is received").
Reviewed-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: NHein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

Just like 0x1600 which got blacklisted by 66a7cbc3 ("ahci: disable
MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes
on NCQ commands if MSI is enabled.  Disable MSI.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NDominik Mierzejewski <dominik@greysector.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=89171
Cc: stable@vger.kernel.org

If kzalloc() failed and then evdev_open_device() fails, evdev_open()
will pass a vmalloc'ed pointer to kfree.

This might fix https://bugzilla.kernel.org/show_bug.cgi?id=88401, where
there was a crash in kfree().
Reported-by: NChristian Casteyde <casteyde.christian@free.fr>
Belatedly-Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Henrik Rydberg <rydberg@euromail.se>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These BUGs can be erroneously triggered by frags which refer to
tail pages within a compound page. The data in these pages may
overrun the hardware page while still being contained within the
compound page, but since compound_order() evaluates to 0 for tail
pages the assertion fails. The code already iterates through
subsequent pages correctly in this scenario, so the BUGs are
unnecessary and can be removed.

Fixes: f36c3747 ("xen/netfront: handle compound page fragments on transmit")
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I was unable too boot 3.18.0-rc6 because of the following kernel
panic in drm_calc_vbltimestamp_from_scanoutpos():

    [drm] Initialized drm 1.1.0 20060810
    [drm] radeon kernel modesetting enabled.
    [drm] initializing kernel modesetting (RV100 0x1002:0x515E 0x15D9:0x8080).
    [drm] register mmio base: 0xC8400000
    [drm] register mmio size: 65536
    radeon 0000:0b:01.0: VRAM: 128M 0x00000000D0000000 - 0x00000000D7FFFFFF (16M used)
    radeon 0000:0b:01.0: GTT: 512M 0x00000000B0000000 - 0x00000000CFFFFFFF
    [drm] Detected VRAM RAM=128M, BAR=128M
    [drm] RAM width 16bits DDR
    [TTM] Zone  kernel: Available graphics memory: 3829346 kiB
    [TTM] Zone   dma32: Available graphics memory: 2097152 kiB
    [TTM] Initializing pool allocator
    [TTM] Initializing DMA pool allocator
    [drm] radeon: 16M of VRAM memory ready
    [drm] radeon: 512M of GTT memory ready.
    [drm] GART: num cpu pages 131072, num gpu pages 131072
    [drm] PCI GART of 512M enabled (table at 0x0000000037880000).
    radeon 0000:0b:01.0: WB disabled
    radeon 0000:0b:01.0: fence driver on ring 0 use gpu addr 0x00000000b0000000 and cpu addr 0xffff8800bbbfa000
    [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [drm] Driver supports precise vblank timestamp query.
    [drm] radeon: irq initialized.
    [drm] Loading R100 Microcode
    radeon 0000:0b:01.0: Direct firmware load for radeon/R100_cp.bin failed with error -2
    radeon_cp: Failed to load firmware "radeon/R100_cp.bin"
    [drm:r100_cp_init] *ERROR* Failed to load firmware!
    radeon 0000:0b:01.0: failed initializing CP (-2).
    radeon 0000:0b:01.0: Disabling GPU acceleration
    [drm] radeon: cp finalized
    BUG: unable to handle kernel NULL pointer dereference at 000000000000025c
    IP: [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
    PGD 0
    Oops: 0000 [#1] SMP
    Modules linked in:
    CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.18.0-rc6-4-default #2649
    Hardware name: Supermicro X7DB8/X7DB8, BIOS 6.00 07/26/2006
    task: ffff880234da2010 ti: ffff880234da4000 task.ti: ffff880234da4000
    RIP: 0010:[<ffffffff8150423b>]  [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
    RSP: 0000:ffff880234da7918  EFLAGS: 00010086
    RAX: ffffffff81557890 RBX: 0000000000000000 RCX: ffff880234da7a48
    RDX: ffff880234da79f4 RSI: 0000000000000000 RDI: ffff880232e15000
    RBP: ffff880234da79b8 R08: 0000000000000000 R09: 0000000000000000
    R10: 000000000000000a R11: 0000000000000001 R12: ffff880232dda1c0
    R13: ffff880232e1518c R14: 0000000000000292 R15: ffff880232e15000
    FS:  0000000000000000(0000) GS:ffff88023fc40000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
    CR2: 000000000000025c CR3: 0000000002014000 CR4: 00000000000007e0
    Stack:
     ffff880234da79d8 0000000000000286 ffff880232dcbc00 0000000000002480
     ffff880234da7958 0000000000000296 ffff880234da7998 ffffffff8151b51d
     ffff880234da7a48 0000000032dcbeb0 ffff880232dcbc00 ffff880232dcbc58
    Call Trace:
     [<ffffffff8151b51d>] ? drm_vma_offset_remove+0x1d/0x110
     [<ffffffff8152dc98>] radeon_get_vblank_timestamp_kms+0x38/0x60
     [<ffffffff8152076a>] ? ttm_bo_release_list+0xba/0x180
     [<ffffffff81503751>] drm_get_last_vbltimestamp+0x41/0x70
     [<ffffffff81503933>] vblank_disable_and_save+0x73/0x1d0
     [<ffffffff81106b2f>] ? try_to_del_timer_sync+0x4f/0x70
     [<ffffffff81505245>] drm_vblank_cleanup+0x65/0xa0
     [<ffffffff815604fa>] radeon_irq_kms_fini+0x1a/0x70
     [<ffffffff8156c07e>] r100_init+0x26e/0x410
     [<ffffffff8152ae3e>] radeon_device_init+0x7ae/0xb50
     [<ffffffff8152d57f>] radeon_driver_load_kms+0x8f/0x210
     [<ffffffff81506965>] drm_dev_register+0xb5/0x110
     [<ffffffff8150998f>] drm_get_pci_dev+0x8f/0x200
     [<ffffffff815291cd>] radeon_pci_probe+0xad/0xe0
     [<ffffffff8141a365>] local_pci_probe+0x45/0xa0
     [<ffffffff8141b741>] pci_device_probe+0xd1/0x130
     [<ffffffff81633dad>] driver_probe_device+0x12d/0x3e0
     [<ffffffff8163413b>] __driver_attach+0x9b/0xa0
     [<ffffffff816340a0>] ? __device_attach+0x40/0x40
     [<ffffffff81631cd3>] bus_for_each_dev+0x63/0xa0
     [<ffffffff8163378e>] driver_attach+0x1e/0x20
     [<ffffffff81633390>] bus_add_driver+0x180/0x240
     [<ffffffff81634914>] driver_register+0x64/0xf0
     [<ffffffff81419cac>] __pci_register_driver+0x4c/0x50
     [<ffffffff81509bf5>] drm_pci_init+0xf5/0x120
     [<ffffffff821dc871>] ? ttm_init+0x6a/0x6a
     [<ffffffff821dc908>] radeon_init+0x97/0xb5
     [<ffffffff810002fc>] do_one_initcall+0xbc/0x1f0
     [<ffffffff810e3278>] ? __wake_up+0x48/0x60
     [<ffffffff8218e256>] kernel_init_freeable+0x18a/0x215
     [<ffffffff8218d983>] ? initcall_blacklist+0xc0/0xc0
     [<ffffffff818a78f0>] ? rest_init+0x80/0x80
     [<ffffffff818a78fe>] kernel_init+0xe/0xf0
     [<ffffffff818c0c3c>] ret_from_fork+0x7c/0xb0
     [<ffffffff818a78f0>] ? rest_init+0x80/0x80
    Code: 45 ac 0f 88 a8 01 00 00 3b b7 d0 01 00 00 49 89 ff 0f 83 99 01 00 00 48 8b 47 20 48 8b 80 88 00 00 00 48 85 c0 0f 84 cd 01 00 00 <41> 8b b1 5c 02 00 00 41 8b 89 58 02 00 00 89 75 98 41 8b b1 60
    RIP  [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
     RSP <ffff880234da7918>
    CR2: 000000000000025c
    ---[ end trace ad2c0aadf48e2032 ]---
    Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009

It has helped me to add a NULL pointer check that was suggested at
http://lists.freedesktop.org/archives/dri-devel/2014-October/070663.html

I am not familiar with the code. But the change looks sane
and we need something fast at this stage of 3.18 development.
Suggested-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NPetr Mladek <pmladek@suse.cz>
Tested-by: NPetr Mladek <pmladek@suse.cz>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=84627Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Not just the userspace relocs, otherwise we won't wait
for a swapped out page tables to be swapped in again.

v2: rebased on Alex current drm-fixes-3.18
Signed-off-by: NChristian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

irq_of_parse_and_map() returns 0 on error (the result is unsigned int),
so testing for negative result never works.
Signed-off-by: NDmitry Torokhov <dtor@chromium.org>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

This patch adds DeviceIDs for Sunrise Point-LP.
Signed-off-by: NDevin Ryles <devin.ryles@intel.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

Otherwise we'll have backtraces in assert_panel_unlocked because the
BIOS locks the register. In the reporter's case this regression was
introduced in

commit c31407a3
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Thu Oct 18 21:07:01 2012 +0100

    drm/i915: Add no-lvds quirk for Supermicro X7SPA-H
Reported-by: NAlexey Orishko <alexey.orishko@gmail.com>
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Francois Tigeot <ftigeot@wolfpond.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Tested-by: NAlexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Apparently PCH fifo underruns are tricky, we have plenty reports that
we see the occasional underrun (especially at boot-up).

So for a change let's see what happens when we don't re-enable pch
fifo underrun reporting when the pipe is disabled. This means that the
kernel can't catch pch fifo underruns when they happen (except when
all pipes are on on the pch). But we'll still catch underruns when
disabling the pipe again. So not a terrible reduction in test
coverage.

Since the DRM_ERROR is new and hence a regression plan B would be to
revert it back to a debug output. Which would be a lot worse than this
hack for underrun test coverage in the wild. See the referenced
discussions for more.

References: http://mid.gmane.org/CA+gsUGRfGe3t4NcjdeA=qXysrhLY3r4CEu7z4bjTwxi1uOfy+g@mail.gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=86233
References: https://bugs.freedesktop.org/show_bug.cgi?id=86478Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Tested-by: Nlu hua <huax.lu@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Introduced in b440bde7, however it was added to
the wrong function in nouveau.

https://bugzilla.kernel.org/show_bug.cgi?id=86011
Cc: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org  # v3.15+
Signed-off-by: NDave Airlie <airlied@redhat.com>

Indications are that no GF116's actually have a copy engine there, but
actually have the decompression engine. This engine can be made to do
copies, but that should be done separately.

Unclear why this didn't turn up on all GF116's, but perhaps the
non-mobile ones came with enough VRAM to not trigger ttm migrations in
test scenarios.

Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=85465
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=59168
Cc: stable@vger.kernel.org
Signed-off-by: NIlia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Tested-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Closes a very unlikely race that can occur if another NonStallInterrupt
method passes between checking fences and acking the previous interrupt.

With this change, the interrupt will re-fire under such conditions.
Tested-by: NTobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Commit 0b0b0893 ("of/pci: Fix the conversion of IO ranges into IO
resources") changed how I/O resources are parsed from DT.  Rather than
containing the physical address of the I/O region, the addresses will now
be in I/O address space.

On Tegra the union of all ranges is used to expose a top-level memory-
mapped resource for the PCI host bridge.  This helps to make /proc/iomem
more readable.

Combining both of the above, the union would now include the I/O space
region.  This causes a regression on Tegra20, where the physical base
address of the PCIe controller (and therefore of the union) is located at
physical address 0x80000000.  Since I/O space starts at 0, the union will
now include all of system RAM which starts at 0x00000000.

This commit fixes this by keeping two copies of the I/O range: one that
represents the range in the CPU's physical address space, the other for the
range in the I/O address space.  This allows the translation setup within
the driver to reuse the physical addresses.  The code registering the I/O
region with the PCI core uses both ranges to establish the mapping.

Fixes: 0b0b0893 ("of/pci: Fix the conversion of IO ranges into IO resources")
Reported-by: NMarc Zyngier <marc.zyngier@arm.com>
Tested-by: NMarc Zyngier <marc.zyngier@arm.com>
Suggested-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>

Commit 0b8db271 ("ACPI / video: check _DOD list when creating
backlight devices") checks if the video device is in the bind devices
list to decide if we should create backlight device for it, that causes
problem for one Dell Latitude E6410, where none of the video output
devices are properly bound due to the way how we did the comparing
between its _ADR and the _DOD's values. Solve this problem by comparing
the lower 12 bits of both the device's _ADR and the _DOD's values instead
of relying on bind result.

Fixes: 0b8db271 ("ACPI / video: check _DOD list when creating backlight devices")
Reported-and-tested-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NAaron Lu <aaron.lu@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This resolves the following bug which can be reproduced by building the
kernel with CONFIG_DEBUG_ATOMIC_SLEEP=y and reading network statistics
while the network interface is down.

e.g.:

ifconfig eth0 down
cat /sys/class/net/eth0/statistics/tx_errors

----
[ 1238.161349] BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:952
[ 1238.188279] in_atomic(): 1, irqs_disabled(): 0, pid: 1388, name: cat
[ 1238.207425] CPU: 0 PID: 1388 Comm: cat Not tainted 3.10.31-ltsi-00046-gefa0b46 #1087
[ 1238.230737] Backtrace:
[ 1238.238123] [<c0012e64>] (dump_backtrace+0x0/0x10c) from [<c0013000>] (show_stack+0x18/0x1c)
[ 1238.263499]  r6:000003b8 r5:c06160c0 r4:c0669e00 r3:00404000
[ 1238.280583] [<c0012fe8>] (show_stack+0x0/0x1c) from [<c04515a4>] (dump_stack+0x20/0x28)
[ 1238.304631] [<c0451584>] (dump_stack+0x0/0x28) from [<c004970c>] (__might_sleep+0xf8/0x118)
[ 1238.329734] [<c0049614>] (__might_sleep+0x0/0x118) from [<c02465ac>] (__pm_runtime_resume+0x38/0x90)
[ 1238.357170]  r7:d616f000 r6:c049c458 r5:00000004 r4:d6a17210
[ 1238.374251] [<c0246574>] (__pm_runtime_resume+0x0/0x90) from [<c029b1c4>] (sh_eth_get_stats+0x44/0x280)
[ 1238.402468]  r7:d616f000 r6:c049c458 r5:d5c21000 r4:d5c21000
[ 1238.419552] [<c029b180>] (sh_eth_get_stats+0x0/0x280) from [<c03ae39c>] (dev_get_stats+0x54/0x88)
[ 1238.446204]  r5:d5c21000 r4:d5ed7e08
[ 1238.456980] [<c03ae348>] (dev_get_stats+0x0/0x88) from [<c03c677c>] (netstat_show.isra.15+0x54/0x9c)
[ 1238.484413]  r6:d5c21000 r5:d5c21238 r4:00000028 r3:00000001
[ 1238.501495] [<c03c6728>] (netstat_show.isra.15+0x0/0x9c) from [<c03c69b8>] (show_tx_errors+0x18/0x1c)
[ 1238.529196]  r7:d5f945d8 r6:d5f945c0 r5:c049716c r4:c0650e7c
[ 1238.546279] [<c03c69a0>] (show_tx_errors+0x0/0x1c) from [<c023963c>] (dev_attr_show+0x24/0x50)
[ 1238.572157] [<c0239618>] (dev_attr_show+0x0/0x50) from [<c010c148>] (sysfs_read_file+0xb0/0x140)
[ 1238.598554]  r5:c049716c r4:d5c21240
[ 1238.609326] [<c010c098>] (sysfs_read_file+0x0/0x140) from [<c00b9ee4>] (vfs_read+0xb0/0x13c)
[ 1238.634679] [<c00b9e34>] (vfs_read+0x0/0x13c) from [<c00ba0ac>] (SyS_read+0x44/0x74)
[ 1238.657944]  r8:bef45bf0 r7:00000000 r6:d6ac0600 r5:00000000 r4:00000000
[ 1238.678172] [<c00ba068>] (SyS_read+0x0/0x74) from [<c000eec0>] (ret_fast_syscall+0x0/0x30)
----
Signed-off-by: NMitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Original code only check/alloc plat_dat for the CONFIG_OF case, this
patch check/alloc it earlier and unconditionally to avoid kernel build
warnings:

drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:275
stmmac_pltfr_probe() warn: variable dereferenced before check 'plat_dat'

V2: Fix coding style.
Signed-off-by: NHuacai Chen <chenhc@lemote.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the current driver, allocation size of skb does not care the alignment
adjust after allocation.
And also, in the current implementation, buffer alignment method by
sh_eth_set_receive_align function has a bug that this function displace
buffer start address forcedly when the alignment is corrected.
In the result, tail of the skb will exceed allocated area and kernel panic
will be occurred.
This patch fix this issue.
Signed-off-by: NMitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes: 7f28fa10 ("bonding: add arp_ip_target netlink support")
Reported-by: NJohn Fastabend <john.fastabend@gmail.com>
Cc: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DLink GO-USB-N150 with revision B1 uses this driver.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If ddc fails, presumably the i2c mux (and hopefully the signal
mux) are switched to the other GPU so don't fetch the edid from
the vbios so that the connector reports disconnected.

bug:
https://bugzilla.opensuse.org/show_bug.cgi?id=904417Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

In commit fadbe0cd entitled "staging:
rtl8188eu:Remove rtw_zmalloc(), wrapper for kzalloc()", the author failed
to note that the original code in the wrapper tested whether the caller
could sleep, and set the flags argument to kzalloc() appropriately.
After the patch, GFP_KERNEL is used unconditionally. Unfortunately, several
of the routines may be entered from an interrupt routine and generate
a BUG splat for every such call. Routine rtw_sitesurvey_cmd() is used in the
example below:

BUG: sleeping function called from invalid context at mm/slub.c:1240
in_atomic(): 1, irqs_disabled(): 0, pid: 756, name: wpa_supplicant
INFO: lockdep is turned off.
CPU: 2 PID: 756 Comm: wpa_supplicant Tainted: G        WC O   3.18.0-rc4+ #34
Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.20   04/17/2014
ffffc90005557000 ffff880216fafaa8 ffffffff816b0bbf 0000000000000000
ffff8800c3b58000 ffff880216fafac8 ffffffff8107af77 0000000000000001
0000000000000010 ffff880216fafb18 ffffffff811b06ce 0000000000000000
Call Trace:
 [<ffffffff816b0bbf>] dump_stack+0x4e/0x71
 [<ffffffff8107af77>] __might_sleep+0xf7/0x120
 [<ffffffff811b06ce>] kmem_cache_alloc_trace+0x4e/0x1f0
 [<ffffffffa0888226>] ? rtw_sitesurvey_cmd+0x56/0x2a0 [r8188eu]
 [<ffffffffa0888226>] rtw_sitesurvey_cmd+0x56/0x2a0 [r8188eu]
 [<ffffffffa088f00d>] rtw_do_join+0x22d/0x370 [r8188eu]
 [<ffffffffa088f6e8>] rtw_set_802_11_ssid+0x218/0x3d0 [r8188eu]
 [<ffffffffa08c3ca5>] rtw_wx_set_essid+0x1e5/0x410 [r8188eu]
 [<ffffffffa08c3ac0>] ? rtw_wx_get_rate+0x50/0x50 [r8188eu]
 [<ffffffff816938f1>] ioctl_standard_iw_point+0x151/0x3f0
 [<ffffffff81693d52>] ioctl_standard_call+0xb2/0xe0
 [<ffffffff81597df7>] ? rtnl_lock+0x17/0x20
 [<ffffffff816945a0>] ? iw_handler_get_private+0x70/0x70
 [<ffffffff81693ca0>] ? call_commit_handler+0x40/0x40
 [<ffffffff81693256>] wireless_process_ioctl+0x176/0x1c0
 [<ffffffff81693e79>] wext_handle_ioctl+0x69/0xc0
 [<ffffffff8159fe79>] dev_ioctl+0x309/0x5e0
 [<ffffffff810be9c7>] ? call_rcu+0x17/0x20
 [<ffffffff8156a472>] sock_ioctl+0x142/0x2e0
 [<ffffffff811e0c70>] do_vfs_ioctl+0x300/0x520
 [<ffffffff81101514>] ? __audit_syscall_entry+0xb4/0x110
 [<ffffffff81101514>] ? __audit_syscall_entry+0xb4/0x110
 [<ffffffff810102bc>] ? do_audit_syscall_entry+0x6c/0x70
 [<ffffffff811e0f11>] SyS_ioctl+0x81/0xa0
 [<ffffffff816ba1d2>] system_call_fastpath+0x12/0x17

Additional routines that generate this BUG are rtw_joinbss_cmd(),
rtw_dynamic_chk_wk_cmd(), rtw_lps_ctrl_wk_cmd(), rtw_rpt_timer_cfg_cmd(),
rtw_ps_cmd(), report_survey_event(), report_join_res(), survey_timer_hdl(),
and rtw_check_bcn_info().
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: navin patidar <navin.patidar@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ndo_bridge_setlink() is currently only called on the slave if
IFLA_AF_SPEC is set but this is a very fragile assumption and may
change in the future.

Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Payload is currently accessed blindly and may exceed valid message
boundaries.

Fixes: a77dcb8c ("be2net: set and query VEB/VEPA mode of the PF interface")
Fixes: 815cccbf ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 3b57de95 brought the support for a different amount of
the filter bins, but didn't update the platform driver that without
CONFIG_OF.

Fixes: 3b57de95 (net: stmmac: Support devicetree configs for mcast
and ucast filter entries)
Signed-off-by: NHuacai Chen <chenhc@lemote.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some VF drivers use the upper byte of "param1" (the qp count field)
in mlx4_qp_reserve_range() to pass flags which are used to optimize
the range allocation.

Under the current code, if any of these flags are set, the 32-bit
count field yields a count greater than 2^24, which is out of range,
and this VF fails.

As these flags represent a "best-effort" allocation hint anyway, they may
safely be ignored. Therefore, the PF driver may simply mask out the bits.

Fixes: c82e9aa0 "mlx4_core: resource tracking for HCA resources used by guests"
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Our boot agent may have left the switch in an certain configuration
state, make sure we issue a software reset prior to configuring the
switch in order to ensure the HW is in a consistent state, in particular
transmit queues and internal buffers.

Fixes: 246d7f77 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case we fail to ioremap() one of our registers, we would be leaking
existing mappings, unwind those accordingly on errors.

Fixes: 246d7f77 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

memblock_is_region_reserved() returns true in the case of a partial
overlap, meaning that the current code fails to reserve the
non-overlapping portion.

This call was introduced as part of d1552ce4 "of/fdt: move
memreserve and dtb memory reservations into core" which went into
v3.16.

I observed this causing a Midway system with a buggy fdt (the header
declares itself to be larger than it really is) failing to boot
because the over-inflated size of the fdt was causing it to seem to
run into the swapper_pg_dir region, meaning the DT wasn't reserved.
The symptoms were failing to find an disks or network and failing to
boot.

However given the ambiguity of whether things like the initrd are
covered by /memreserve/ and similar I think it is best to also
register the region rather than just ignoring it.

Since memblock_reserve() handles overlaps just fine lets just warn and
carry on.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: stable@vger.kernel.org # v3.16+

Currently we just make sure vdd is off before suspending, but we don't
cancel the vdd off work. The work wil not touch vdd if
want_panel_vdd==false so in theory this is fine.

In the past that was perfectly fine since the vdd off work didn't do
anything when want_panel_vdd==false, so even if the work would have been
run during system resume before i915 has resumed, nothing would happen.

However since pps_lock() will now grab the power domain references before
it can check want_panel_vdd, we may end up toggling the power wells on/off
already before the driver has resumed. That is not really acceptable, so
cancel the vdd off work when suspending the encoder.

The problem appeared when pps_lock() was introduced in:
 commit 773538e8
 Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
 Date:   Thu Sep 4 14:54:56 2014 +0300

    drm/i915: Reset power sequencer pipe tracking when disp2d is off
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

If no voltage supply regulators are defined for the UFS devices (assumed
they are always-on), ufshcd_config_vreg_load() can be called on
suspend/resume paths with vreg == NULL as hba->vreg_info.vcc* equal to
NULL, and it causes NULL pointer dereference.

This fixes it by making ufshcd_config_vreg_{h,l}pm noop when no regulators
are defined.
Signed-off-by: NAkinobu Mita <mita@fixstars.com>
Reviewed-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

When dynamic clk gating feature is enabled, delayed workqueue machanism
is used in order to detect certain period of inactivity.  But there is no
guarantee that scheduled gating work is completed before module unloading.
So it can cause kernel crash by accessing memory after it was freed.

Fix it by cancelling clk gating and ungating works and ensure that its
execution is finished before module unloading.
Signed-off-by: NAkinobu Mita <mita@fixstars.com>
Reviewed-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Return value of irq_of_parse_and_map() is unsigned int, with 0
indicating failure, so testing for negative result never works.
Signed-off-by: NDmitry Torokhov <dtor@chromium.org>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: Kevin Cernekee <cernekee@gmail.com> 
Link: https://lkml.kernel.org/r/20141114221642.GA37468@dtor-wsSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Return value of irq_of_parse_and_map() is unsigned int, with 0
indicating failure, so testing for negative result never works.
Signed-off-by: NDmitry Torokhov <dtor@chromium.org>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NKevin Cernekee <cernekee@gmail.com>
Link: https://lkml.kernel.org/r/20141114221614.GA37395@dtor-wsSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This reverts commit 2dea53bf.

Turns out to be broken :(

Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>