Add the debugfs framework to the driver and create a debugfs
command interface for each device.

example command:
"echo queue info > cmd" Query the packet forwarding queue information.
Signed-off-by: Nliuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently netdev is down in enet module, and it is before
mtu range checking in hclge module, which may be cause
netdev being down unnecessarily.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently there is no way for pf to know if a vf device is
alive or not, so PF does not know which vf to notify when
reset happens, or which vf's mtu is invalid when vf and pf
share the same hardware mtu setting.

This patch adds vport alive state checking support, in order
to support the above scenario.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refactors mac mtu setting related functions,
normalizes the use of mps and mtu.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds supports for two vlan header when setting mtu.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When HW GRO enable, protocol stack will not do GRO again,
driver should add gro param to the skb for the protocol
stack..
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MAX_SKB_FRAGS in protocol stack is defined as:

MAX_SKB_FRAGS is 17 when PAGE_SIZE is 4K. If HW enable GRO, it may
merge small packets and the rx buffer may be more than
MAX_SKB_FRAGS. So driver will add skb chain when RX buffer num.
more than MAX_SKB_FRAGS.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support of ethtool -K to enable/disable
hardware GRO in HNS3 PF/VF driver.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "FE bit" in the description means the last description for
a packets. When HW GRO enable, HW write data to ring every
packet/buffer, there is greater probability that driver handle
with the describtion but HW still not set the "FE bit".

When drier handle the packet and HW still not set "FE bit",
driver stores skb and bd_num in rx ring, and continue to use the
skb and bd_num in next napi.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HNS3 hardware Revision B(=0x21) supports Hardware GRO feature. This
patch enables this feature in the HNS3 PF/VF driver.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While doing PF FLR, VF's PCIe configuration space will be cleared, so
the pci and vector of VF should be re-initialized in the VF's reset
process while PF doing FLR.

Also, this patch fixes some memory not freed problem when pci
re-initialization is done during reset process.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the .reset_prepare and .reset_done
ops from pci framework to support the PF FLR.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When calling napi_disable during reset down process, if NAPIF_STATE_MISSED
is set, napi_complete will call __napi_schedule to do the polling again.
So this patch uses HNS3_NIC_STATE_DOWN to ensure the polling is not
scheduled again.

Also, when napi_complete returns true, it means polling is scheduled
again, it is not neccssary to enable the interrupt.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hns3_reset_notify_init_enet() only return error early if the return
value of hns3_restore_vlan() is not 0.

This patch adds checking for the return value of hns3_restore_vlan.

Fixes: 7fa6be4f ("net: hns3: fix incorrect return value/type of some functions")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saving reset related information in the hclge_dev/hclgevf_dev
structure is more suitable than the hnae3_handle, since hardware
related information is kept in these two structure.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While hclge is going to reset, it will notify its client with
HNAE3_DOWN_CLIENT, so this client should get into a resetting
status from this moment, other operations from the stack need to
be blocked as well. And when the reset is finished, the client
will be notified with HNAE3_UP_CLIENT, so this is the end of
the resetting status.

This patch uses HNS3_NIC_STATE_RESETTING flag to implement that,
and adds hns3_nic_resetting() to indicate which operation is not
allowed.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While hardware gets into reset status, the firmware will not respond to
driver's command request, which may cause ring not disabled problem
during reset process.

So this patch uses register instead of command to enable/disable the ring
in the enet while doing UP/DOWN operation.

Also, HNS3_RING_RX_VM_REG is previously unused, so change it to the
correct meaning, and add a wrapper function for readl().

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing a function reset, the hardware table should be cleared
before the hardware reset. In current code, this clearing is done
in hns3_reset_notify_uninit_enet, but it is too late, because
the hardware reset is already done, hns3_reset_notify_down_enet
is more suitable to do that.

Fixes: bb6b94a8 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Besides of module_init and module_exit, the process of reset will
also uninitialize and initialize the enet client. When reset process
fails with enet client uninitialized, the module_exit does not need
to uninitialize the enet client, otherwise it may cause double
uninitialization problem.

So we need the HNS3_NIC_STATE_INITED flag to indicate whether
the enet client is initialized.

Also HNS3_NIC_STATE_REINITING is previously unused, so change it to
HNS3_NIC_STATE_INITED.

Fixes: bb6b94a8 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are some functions that, when they fail to send the command,
need to return the corresponding error value to its caller.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: 681ec399 ("net: hns3: fix for vlan table lost problem when resetting")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is not necessary to reset the queue in the hns3_uninit_all_ring(),
since the queue is stopped in the down operation, and will be reset
in the up operation. And the judgment of the HCLGE_STATE_RST_HANDLING
flag in the hclge_reset_tqp() is not correct, because we need to reset
tqp during pf reset, otherwise it may cause queue not being reset to
working state problem.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hns3_get_ring_config()/hns3_queue_to_ring()/
hns3_get_vector_ring_chain() failed during resetting, the allocated
memory has not been freed before these three functions return. So
this patch adds error handler in these functions to fix it.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hns3_nic_init_vector_data() fails to map ring to vector,
it should cancel the netif_napi_add() that has been successfully
done and then exits.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the error recovery for the HNS hw errors.
Signed-off-by: NShiju Jose <shiju.jose@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set of hw errors occurred in the HNS3 are reported to the
hns3 driver through PCIe AER and RAS.The error info will be
processed and appropriately recovered.
This patch adds error_detected callback and error processing.
Signed-off-by: NShiju Jose <shiju.jose@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When sending a big fragment using multiple buffer descriptor,
hns3 does one maping, but do multiple unmapping when tx is done,
which may cause unmapping problem.

To fix it, this patch makes sure the value of desc_cb.length of
the non-first bd is zero. If desc_cb.length is zero, we do not
unmap the buffer.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To keep symmetrical, this patch renames hns_nic_dma_unmap to
hns3_clear_desc.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch unifies big tx fragment handling for tso and non-tso
case.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To solve the L3 checksum error problem which happens when driver
does not clear L3 checksum, DMA map should be done after calling
skb_cow_head.

This patch moves DMA map into hns3_fill_desc to ensure that DMA
map is done after calling skb_cow_head.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes hns3_fill_desc_tso in preparation for
fixing some desc filling bug, because for tso or non-tso
case, we will use the unified hns3_fill_desc.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch resumes promisc mode and vlan filter status after reset.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the driver does nothing when mac vlan table is full.
In this case, the packet with new mac address will be dropped
by hardware. This patch adds check for the result of sync mac
address, and enable promisc mode when mac vlan table is full.
Furtherly, disable vlan filter when enable promisc by user
command.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In revision 0x20, we use vlan id != 0 to check whether a vlan tag
has been offloaded, so vlan id 0 is not supported.

In revision 0x21, rx buffer descriptor adds two bits to indicate
whether one or more vlan tags have been offloaded, so vlan id 0
is valid now.

This patch seperates the handle for vlan id 0, add vlan id 0 support
for revision 0x21.

Fixes: 5b5455a9 ("net: hns3: Add STRP_TAGP field support for hardware revision 0x21")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For mta table support has been dropped, remove the code for mta table.
Signed-off-by: NZhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In original codes, the mac vlan table entries are not cleared when
unload hns3 driver. The dirty mac vlan table entries will make the
result of looking up mac vlan table being unexpected.

When doing core reset or global reset, the firmware will clear all
the tables for driver, and driver shouldn't send any commands to
firmware during reset. But when doing function reset, the driver
needs to clear the tables itself.

This patch clears the mac vlan table entries for each client when
unload driver or reset.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds switch for flow director with ethtool command
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes all flow director rules when unload hns3 driver.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing reset, remove all entries in TCAM block, and keep flow
director rules list. After finishing reset, restore all entries.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow director is a new feature supported by hardware with revision 0x21.
This patch adds flow direcor initialization for each PF. It queries flow
director mode and tcam resource from firmware, selects tuples used for
input key.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>