Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 24 5月, 2006 2 次提交
  3. 19 5月, 2006 1 次提交
  5. 17 5月, 2006 1 次提交
    • R
      IB/mthca: Make fw_cmd_doorbell default to 0 · 1db76c14
      由 Roland Dreier 提交于 
      Setting fw_cmd_doorbell allows FW command to be queued using posted
writes instead of requiring polling on a "go" bit, so it should be a
performance boost.  However, the option causes problems with at least
some device/firmware combinations, so set the default to 0 until we
understand what's going on better.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
      1db76c14
  7. 13 5月, 2006 1 次提交
  9. 11 5月, 2006 1 次提交
  11. 10 5月, 2006 1 次提交
    • R
      IB/mthca: Fix race in reference counting · a3285aa4
      由 Roland Dreier 提交于 
      Fix races in in destroying various objects.  If a destroy routine
waits for an object to become free by doing

	wait_event(&obj->wait, !atomic_read(&obj->refcount));
	/* now clean up and destroy the object */

and another place drops a reference to the object by doing

	if (atomic_dec_and_test(&obj->refcount))
		wake_up(&obj->wait);

then this is susceptible to a race where the wait_event() and final
freeing of the object occur between the atomic_dec_and_test() and the
wake_up().  And this is a use-after-free, since wake_up() will be
called on part of the already-freed object.

Fix this in mthca by replacing the atomic_t refcounts with plain old
integers protected by a spinlock.  This makes it possible to do the
decrement of the reference count and the wake_up() so that it appears
as a single atomic operation to the code waiting on the wait queue.

While touching this code, also simplify mthca_cq_clean(): the CQ being
cleaned cannot go away, because it still has a QP attached to it.  So
there's no reason to be paranoid and look up the CQ by number; it's
perfectly safe to use the pointer that the callers already have.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
      a3285aa4
  13. 02 5月, 2006 12 次提交
  15. 20 4月, 2006 3 次提交
  17. 13 4月, 2006 1 次提交
    • J
      IB/mthca: Fix max_srq_sge returned by ib_query_device for Tavor devices · 59fef3b1
      由 Jack Morgenstein 提交于 
      The driver allocates SRQ WQEs size with a power of 2 size both for
Tavor and for memfree. For Tavor, however, the hardware only requires
the WQE size to be a multiple of 16, not a power of 2, and the max
number of scatter-gather allowed is reported accordingly by the
firmware (and this is the value currently returned by
ib_query_device() and ibv_query_device()).

If the max number of scatter/gather entries reported by the FW is used
when creating an SRQ, the creation will fail for Tavor, since the
required WQE size will be increased to the next power of 2, which
turns out to be larger than the device permitted max WQE size (which
is not a power of 2).

This patch reduces the reported SRQ max wqe size so that it can be used
successfully in creating an SRQ on Tavor HCAs.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
      59fef3b1
  19. 11 4月, 2006 2 次提交
    • M
      IB/mthca: Disable tuning PCI read burst size · abf45dbb
      由 Michael S. Tsirkin 提交于 
      The PCI spec recommends against drivers playing with a device's PCI
read burst size, and says that systems software should configure it.
And we actually have users that report that changing it from the
default set by BIOS hurts performance and/or stability for them.  On
the other hand, the Mellanox Programmer's Reference Manual recommends
turning it up all the way to the maximum value.  Some tests conducted
here in the lab do not show performance improvement from this tuning,
but this might be just me.

As a work-around, make this tuning an option, off by default (safe
value), with an eye towards removing it completely one day if no one
complains.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
      abf45dbb
    • J
      IB: simplify static rate encoding · bf6a9e31
      由 Jack Morgenstein 提交于 
      Push translation of static rate to HCA format into low-level drivers,
where it belongs.  For static rate encoding, use encoding of rate
field from IB standard PathRecord, with addition of value 0, for
backwards compatibility with current usage.  The changes are:

 - Add enum ib_rate to midlayer includes.
 - Get rid of static rate translation in IPoIB; just use static rate
   directly from Path and MulticastGroup records.
 - Update mthca driver to translate absolute static rate into the
   format used by hardware.  This also fixes mthca's static rate
   handling for HCAs that are capable of 4X DDR.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
      bf6a9e31
  21. 03 4月, 2006 1 次提交
    • R
      IB/mthca: Always build debugging code unless CONFIG_EMBEDDED=y · 227c939b
      由 Roland Dreier 提交于 
      Change the mthca debugging trace output code so that it can enabled
and disabled at runtime with the debug_level module parameter in
sysfs.  Also, don't allow CONFIG_INFINIBAND_MTHCA_DEBUG to be disabled
unless CONFIG_EMBEDDED is selected.  We want users (and especially
distros) to have this turned on unless they really need to save space,
because by the time we want debugging output, it's usually too late to
rebuild a kernel.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
      227c939b
  23. 01 4月, 2006 14 次提交