If bios sets up an MST output and hardware state readout code sees this is
an SST configuration, when disabling the encoder we end up calling
->post_disable_dp() hook instead of the MST version. Consequently, we write
to the DP_SET_POWER dpcd to set it D3 state. Further along when we try
enable the encoder in MST mode, POWER_UP_PHY transaction fails to power up
the MST hub. This results in continuous link training failures which keep
the system busy delaying boot. We could identify bios MST boot discrepancy
and handle it accordingly but a simple way to solve this is to write to the
DP_SET_POWER dpcd for MST too.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105470
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: NLaura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 5ea2355a ("drm/i915/mst: Use MST sideband message transactions for dpms control")
Tested-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314054825.1718-1-dhinakaran.pandiyan@intel.com
(cherry picked from commit ad260ab3)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Fixes: 3c66c87d ("drm/nouveau/disp: remove hw-specific customisation
of output paths")
Suggested-by: NBen Skeggs <skeggsb@redhat.com>
Signed-off-by: NKarol Herbst <kherbst@redhat.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Unbinding nouveau on a dual GPU MacBook Pro oopses because we iterate
over the bl_connectors list in nouveau_backlight_exit() but skipped
initializing it in nouveau_backlight_init().  Stacktrace for posterity:

    BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
    IP: nouveau_backlight_exit+0x2b/0x70 [nouveau]
    nouveau_display_destroy+0x29/0x80 [nouveau]
    nouveau_drm_unload+0x65/0xe0 [nouveau]
    drm_dev_unregister+0x3c/0xe0 [drm]
    drm_put_dev+0x2e/0x60 [drm]
    nouveau_drm_device_remove+0x47/0x70 [nouveau]
    pci_device_remove+0x36/0xb0
    device_release_driver_internal+0x157/0x220
    driver_detach+0x39/0x70
    bus_remove_driver+0x51/0xd0
    pci_unregister_driver+0x2a/0xa0
    nouveau_drm_exit+0x15/0xfb0 [nouveau]
    SyS_delete_module+0x18c/0x290
    system_call_fast_compare_end+0xc/0x6f

Fixes: b53ac1ee ("drm/nouveau/bl: Do not register interface if Apple GMUX detected")
Cc: stable@vger.kernel.org # v4.10+
Cc: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Commit 7110c89bb8852ff8b0f88ce05b332b3fe22bd11e ("mmu: swap out round
for ALIGN") replaced two calls to round/rounddown with ALIGN/ALIGN_DOWN,
but erroneously applied ALIGN_DOWN to a different variable (addr) and left
intended variable (tail) not rounded/ALIGNed.

As a result screen corruption, X lockups are observable. An example of kernel
log of affected system with NV98 card where it was bisected:

nouveau 0000:01:00.0: gr: TRAP_M2MF 00000002 [IN]
nouveau 0000:01:00.0: gr: TRAP_M2MF 00320951 400007c0 00000000 04000000
nouveau 0000:01:00.0: gr: 00200000 [] ch 1 [000fbbe000 DRM] subc 4 class 5039
mthd 0100 data 00000000
nouveau 0000:01:00.0: fb: trapped read at 0040000000 on channel 1
[0fbbe000 DRM]
engine 00 [PGRAPH] client 03 [DISPATCH] subclient 04 [M2M_IN] reason 00000006
[NULL_DMAOBJ]

Fixes bug 105173 ("[MCP79][Regression] Unhandled NULL pointer dereference in
nvkm_object_unmap since kernel 4.15")
https://bugs.freedesktop.org/show_bug.cgi?id=105173

Fixes: 7110c89bb885 ("mmu: swap out round for ALIGN ")
Tested-by: NPierre Moreau <pierre.morrow@free.fr>
Reviewed-by: NPierre Moreau <pierre.morrow@free.fr>
Signed-off-by: NMaris Nartiss <maris.nartiss@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org # v4.15+

This is to fix warning got as:

[ 6730.476938] ------------[ cut here ]------------
[ 6730.476979] Bad or missing usercopy whitelist? Kernel memory exposure attempt detected from SLAB object 'gvt-g_vgpu_workload' (offset 120, size 4)!
[ 6730.477021] WARNING: CPU: 2 PID: 441 at mm/usercopy.c:81 usercopy_warn+0x7e/0xa0
[ 6730.477042] Modules linked in: tun(E) bridge(E) stp(E) llc(E) kvmgt(E) x86_pkg_temp_thermal(E) vfio_mdev(E) intel_powerclamp(E) mdev(E) coretemp(E) vfio_iommu_type1(E) vfio(E) kvm_intel(E) kvm(E) hid_generic(E) irqbypass(E) crct10dif_pclmul(E) crc32_pclmul(E) usbhid(E) i915(E) crc32c_intel(E) hid(E) ghash_clmulni_intel(E) pcbc(E) aesni_intel(E) aes_x86_64(E) crypto_simd(E) cryptd(E) glue_helper(E) intel_cstate(E) idma64(E) evdev(E) virt_dma(E) iTCO_wdt(E) intel_uncore(E) intel_rapl_perf(E) intel_lpss_pci(E) sg(E) shpchp(E) mei_me(E) pcspkr(E) iTCO_vendor_support(E) intel_lpss(E) intel_pch_thermal(E) prime_numbers(E) mei(E) mfd_core(E) video(E) acpi_pad(E) button(E) binfmt_misc(E) ip_tables(E) x_tables(E) autofs4(E) ext4(E) crc16(E) mbcache(E) jbd2(E) fscrypto(E) sd_mod(E) e1000e(E) xhci_pci(E) sdhci_pci(E)
[ 6730.477244]  ptp(E) cqhci(E) xhci_hcd(E) pps_core(E) sdhci(E) mmc_core(E) i2c_i801(E) usbcore(E) thermal(E) fan(E)
[ 6730.477276] CPU: 2 PID: 441 Comm: gvt workload 0 Tainted: G            E    4.16.0-rc1-gvt-staging-0213+ #127
[ 6730.477303] Hardware name:  /NUC6i5SYB, BIOS SYSKLi35.86A.0039.2016.0316.1747 03/16/2016
[ 6730.477326] RIP: 0010:usercopy_warn+0x7e/0xa0
[ 6730.477340] RSP: 0018:ffffba6301223d18 EFLAGS: 00010286
[ 6730.477355] RAX: 0000000000000000 RBX: ffff8f41caae9838 RCX: 0000000000000006
[ 6730.477375] RDX: 0000000000000007 RSI: 0000000000000082 RDI: ffff8f41dad166f0
[ 6730.477395] RBP: 0000000000000004 R08: 0000000000000576 R09: 0000000000000000
[ 6730.477415] R10: ffffffffb1293fb2 R11: 00000000ffffffff R12: 0000000000000001
[ 6730.477447] R13: ffff8f41caae983c R14: ffff8f41caae9838 R15: 00007f183ca2b000
[ 6730.477467] FS:  0000000000000000(0000) GS:ffff8f41dad00000(0000) knlGS:0000000000000000
[ 6730.477489] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 6730.477506] CR2: 0000559462817291 CR3: 000000028b46c006 CR4: 00000000003626e0
[ 6730.477526] Call Trace:
[ 6730.477537]  __check_object_size+0x9c/0x1a0
[ 6730.477562]  __kvm_write_guest_page+0x45/0x90 [kvm]
[ 6730.477585]  kvm_write_guest+0x46/0x80 [kvm]
[ 6730.477599]  kvmgt_rw_gpa+0x9b/0xf0 [kvmgt]
[ 6730.477642]  workload_thread+0xa38/0x1040 [i915]
[ 6730.477659]  ? do_wait_intr_irq+0xc0/0xc0
[ 6730.477673]  ? finish_wait+0x80/0x80
[ 6730.477707]  ? clean_workloads+0x120/0x120 [i915]
[ 6730.477722]  kthread+0x111/0x130
[ 6730.477733]  ? _kthread_create_worker_on_cpu+0x60/0x60
[ 6730.477750]  ? exit_to_usermode_loop+0x6f/0xb0
[ 6730.477766]  ret_from_fork+0x35/0x40
[ 6730.477777] Code: 48 c7 c0 20 e3 25 b1 48 0f 44 c2 41 50 51 41 51 48 89 f9 49 89 f1 4d 89 d8 4c 89 d2 48 89 c6 48 c7 c7 78 e3 25 b1 e8 b2 bc e4 ff <0f> ff 48 83 c4 18 c3 48 c7 c6 09 d0 26 b1 49 89 f1 49 89 f3 eb
[ 6730.477849] ---[ end trace cae869c1c323e45a ]---

By whitelist guest page write from workload struct allocated from kmem cache.
Reviewed-by: NHang Yuan <hang.yuan@linux.intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
(cherry picked from commit 5627705406874df57fdfad3b4e0c9aedd3b007df)

Once the ring buffer is copied to ring_scan_buffer and scanned,
the shadow batch buffer start address is only updated into
ring_scan_buffer, not the real ring address allocated through
intel_ring_begin in later copy_workload_to_ring_buffer.

This patch is only to set the right shadow batch buffer address
from Ring buffer, not include the shadow_wa_ctx.

v2:
- refine some comments. (Zhenyu)
v3:
- fix typo in title. (Zhenyu)
v4:
- remove the unnecessary comments. (Zhenyu)
- add comments in bb_start_cmd_va update. (Zhenyu)

Fixes: 0a53bc07 ("drm/i915/gvt: Separate cmd scan from request allocation")
Cc: stable@vger.kernel.org  # v4.15
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Yulei Zhang <yulei.zhang@intel.com>
Signed-off-by: Nfred gao <fred.gao@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>

Turning off the sink in this case causes various issues, because
userspace expects it to stay on until it turns it off explicitly.

Instead, turn the sink off and back on when a display is connected
again. This dance seems necessary for link training to work correctly.

Bugzilla: https://bugs.freedesktop.org/105308
Cc: stable@vger.kernel.org
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Save/restore the backlight level scratch register in S3/S4 so the
backlight level comes back at the previously requested level.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=199047
Fixes: 4ec6ecf4 (drm/amdgpu: drop scratch regs save and restore from S3/S4 handling)
Acked-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We unmapped imported DMA-bufs when the GEM handle was dropped, not when the
hardware was done with the buffere.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We unmapped imported DMA-bufs when the GEM handle was dropped, not when the
hardware was done with the buffere.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The boost frequency is only applied from the RPS worker while someone is
waiting on a request and requested a boost. As such, when the user
wishes to change the frequency, we have to kick the worker in order to
re-evaluate whether to apply the boost frequency.

v2: Check num_waiters to decide if we should kick the worker to handle
boosting.

Fixes: 29ecd78d ("drm/i915: Define a separate variable and control for RPS waitboost frequency")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308142648.4016-1-chris@chris-wilson.co.uk
(cherry picked from commit 59cd31f1)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Currently, we only allow ourselves to prune the fences so long as
all the waits completed (i.e. all the fences we checked were signaled),
and that the reservation snapshot did not change across the wait.
However, if we only waited for a subset of the reservation object, i.e.
just waiting for the last writer to complete as opposed to all readers
as well, then we would erroneously conclude we could prune the fences as
indeed although all of our waits were successful, they did not represent
the totality of the reservation object.

v2: We only need to check the shared fences due to construction (i.e.
all of the shared fences will be later than the exclusive fence, if
any).

Fixes: e54ca977 ("drm/i915: Remove completed fences after a wait")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307171303.29466-1-chris@chris-wilson.co.uk
(cherry picked from commit fa73055b)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Currently, BXT_PP is hardcoded with value '0'.
It practically disabled eDP backlight on MRB (BXT) platform.

This patch will tell which BXT_PP registers (there are two set of
PP_CONTROL in the spec) to be used as defined in VBT (Video Bios Timing
table) and this will enabled eDP backlight controller on MRB (BXT)
platform.

v2:
 - Remove unnecessary information in commit message.
 - Assign vbt.backlight.controller to a backlight_controller variable and
   return the variable value.
v3:
 - Rebased to latest code base.
 - updated commit title.
Signed-off-by: NMustamin B Mustaffa <mustamin.b.mustaffa@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227030734.37901-1-mustamin.b.mustaffa@intel.com
(cherry picked from commit 73c0fcac)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

When populating shadow ctx from guest, we should handle oa related
registers in hw ctx, so that they will not be overlapped by guest oa
configs. This patch made it possible to capture oa data from host for
both host and guests.
Signed-off-by: NMin He <min.he@intel.com>
Signed-off-by: NZhi Wang <zhi.a.wang@intel.com>

If user continuously create vgpu, boot guest, shoutdown guest and destroy
vgpu from remote, the following calltrace exists in dmesg sometimes:
[ 6412.954721] RPM wakelock ref not held during HW access
[ 6412.954795] WARNING: CPU: 7 PID: 11941 at
linux/drivers/gpu/drm/i915/intel_drv.h:1800
intel_uncore_forcewake_get.part.7+0x96/0xa0 [i915]
[ 6412.954915] Call Trace:
[ 6412.954951] intel_uncore_forcewake_get+0x18/0x20 [i915]
[ 6412.954989] intel_gvt_switch_mmio+0x8e/0x770 [i915]
[ 6412.954996] ? __slab_free+0x14d/0x2c0
[ 6412.955001] ? __slab_free+0x14d/0x2c0
[ 6412.955006] ? __slab_free+0x14d/0x2c0
[ 6412.955041] intel_vgpu_stop_schedule+0x92/0xd0 [i915]
[ 6412.955073] intel_gvt_deactivate_vgpu+0x48/0x60 [i915]
[ 6412.955078] __intel_vgpu_release+0x55/0x260 [kvmgt]

when this happens, gvt_switch_mmio is called at vgpu destroy, host i915 is
idle and doesn't hold RPM wakelock, igd is in powersave mode, but
gvt_switch_mmio require igd power on to access register, so
intel_runtime_pm_get should be added to make sure igd power on before
gvt_switch_mmio.

v2: Move runtime_pm_get/put into gvt_switch_mmio.(Zhenyu)
Signed-off-by: NXiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: NZhi Wang <zhi.a.wang@intel.com>

In dce110, the plane configuration is such that plane 0
or the primary plane should be rendered with only RGB data.

This patch adds the validation to ensure that no video data
is rendered on plane 0.
Signed-off-by: NShirish S <shirish.s@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When UVD is in VM mode, there is not uvd handle exchanged,
uvd.handles are always 0. So vcpu_bo always need save,
Otherwise amdgpu driver will fail during suspend/resume.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105021Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Reviewed-by: NLeo Liu <leo.liu@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Max uvd handles should use adev->uvd.max_handles instead of
AMDGPU_MAX_UVD_HANDLES here.
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Reviewed-by: NLeo Liu <leo.liu@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The work around for hw bug causes S3 resume failure. Don't execute
disable vga logic if not in vga mode.
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

HW Engineer's Notes:
 During switch from vga->extended, if we set the VGA_TEST_ENABLE and then
 hit the VGA_TEST_RENDER_START, then the DCHUBP timing gets updated correctly.
 Then vBIOS will have it poll for the VGA_TEST_RENDER_DONE and unset
 VGA_TEST_ENABLE, to leave it in the same state as before.
Signed-off-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

While checking plane states for updates during atomic check, we create
dc_plane_states in preparation. These dc states should be freed if
something errors.

Although the input transfer function is also freed by
dc_plane_state_release(), we should free it (on error) under the same
scope as where it is created.
Signed-off-by: NLeo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NRoman Li <Roman.Li@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Before dig fe is enabled, infoframe can't be programmed. So in
suspend resume case our infoframe programmming was not going through.

This change changes the sequence so that infoframe is programmed
after.
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fixing null-deref on Vega10 due to regression after
'fix cursor related Pstate hang' change.
Added null checks in setting cursor position.
Signed-off-by: NRoman Li <Roman.Li@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Move cursor programming to inside the OTG_MASTER_UPDATE_LOCK

If graphics plane go from 1 pipe to hsplit, the cursor updates
after mpc programming and unlock. Which means there is a window
of time where cursor is enabled on the wrong pipe if it's on
the right side of the screen (i.e. case where cursor need to
move from pipe 0 to pipe 3 post split). This will cause pstate hang.

Solution is to program the cursor while still locked.
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Because AMDGPU_CRTC_IRQ_VLINE1 = 6, it expected 6 more crtcs to be
programed with disabled irq state in amdgpu_irq_disable_all. That caused errors and accessed
the wrong memory location.
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

There is no need to call drm_mode_set_crtcinfo() again once
crtc timing is decided. Otherwise non-native/unsupported timing
might get overwritten.
Signed-off-by: NJerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

There's no good place in DC to cover all place where stream signal should
be updated. update_stream_signal depends on timing which comes from DM.
Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We've got a helper function to call dc_create_stream_for_sink and one
other place that calls it directly. Make sure we call the helper
functions always since we need to update a bunch of things in stream and
don't want to miss that.
Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Our APUs (Carrizo, Stoney, Raven) don't support it.

v2: Don't use is_apu as other ASICs might also not support it
Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This makes the check for HDMI and dual-link DVI a bit more
straightforward.
Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

With FBC enabled there was a potential null-deref
on topology change due to hardcorded pipe index.
Signed-off-by: NRoman Li <Roman.Li@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When topology changed and rehook up MST display to the same DP
connector, need to take care of drm_dp_mst_port object.

Due to the topology is changed, drm_dp_mst_port and corresponding
i2c_algorithm object could be NULL in such situation.
Signed-off-by: NJerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: NRoman Li <Roman.Li@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The below commit

"drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2"

introduces a slight behavioral change to rmfb. Instead of disabling a crtc
when the primary plane is disabled, it now preserves it.

This change leads to BUG hit while performing atomic commit on amd driver.

As a fix this patch ensures that we disable the CRTC's with NULL FB by returning
-EINVAL and hence triggering fall back to the old behavior and turning off the
crtc in atomic_remove_fb().

V2: Added error check for plane_state and removed sanity check for crtc.
Signed-off-by: NShirish S <shirish.s@amd.com>
Signed-off-by: NPratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

For consistency with other DCE generations.

HPD IRQs appear to be working fine.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

There have been many reports of Ellesmere and Baffin systems not being
able to drive HDMI 4k60 due to the fact that we check the HDMI_6GB_EN
bit from VBIOS table. Windows seems to not have this issue.

On some systems we fail to the encoder cap info from VBIOS. In that case
we should default to enabling HDMI6G support.

This was tested by dwagner on
https://bugs.freedesktop.org/show_bug.cgi?id=102820Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NRoman Li <Roman.Li@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org