These boards need cca setup on CMDLINE.
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fix 64-bit Malta by using CKSEG0ADDR and correct casts.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

LASAT's sysctl interface was broken, it failed a check during boot because
a single entry had a sysctl number and the rest were unnumbered. When I
fixed it I noticed that the whole sysctl file needed a spring clean, it was
using mutexes where it wasn't needed (it's only needed to protect during
writes to the EEPROM), so I moved that stuff out and generally cleaned the
whole thing up.

So now, LASAT's sysctl/proc interface is working again.
Signed-off-by: NThomas Horsten <thomas@horsten.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Assuming the call of kmap_coherent in local_r4k_flush_cache_page doesn't
need fixing this was skipped in fcae549295bcae801ac48fc1c2030ab8cc487020.
Turns out it needed the same change after all.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

After the common MIPS CPU interrupt controller (for irq0-7) was introduced
the Lasat boards didn't get their interrupts right, so nothing worked. The
old routines need to be offset by the new 8 hardware interrupts common to
all MIPS CPU's.
Signed-off-by: NThomas Horsten <thomas@horsten.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NChris Dearman <chris@mips.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NChris Dearman <chris@mips.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 The SWARM defconfig file has not been regenerated for over a year now.
Here is a patch to bring the file up to date.  Additionally some important
and sometimes confusing changes happened meanwhile.  Here is the list of
notable corresponding updates to the configuration:

1. CPU_SB1_PASS_2_2 is now selected rather than CPU_SB1_PASS_1.  The
   latter requires a non-standard -msb1-pass1-workarounds option to be
   supported by GCC and I am told is quite rare anyway.

   [Ralf: Afaik -msb1-pass1-workarounds is available only in Monta Vista's
   special Sibyte gcc 3.0 variant and gcc 3.0 is too old to build a modern
   kernel anyway.]

2. PHYLIB and BROADCOM_PHY are both built in and NETDEV_1000 enabled as
   required by SB1250_MAC.

3. USB and USB_OHCI_HCD are enabled as there is an OHCI chip onboard.

4. TMPFS is enabled, because I use it. ;-)
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 Build the SWARM platform library is as an object rather than an archive
so that files which only contain symbols used by initcalls and do not
provide any symbols that would pull them from an archive still work.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Build error was caused by commit 35133692.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

RM200 with R5ks have a little bit different arcname.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use better load address for big endian kernels to avoid clashes with
PROM / SASH.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Correctly initialize io_map_base for the SB1250 PCI controller as required
for proper iomap support.  Based on a proposal from Daniel Jacobowitz.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In the conversion done in the commits

  95c4eb3ef4484ca85da5c98780d358cffd546b90
  9d360ab4

  [MIPS] Alchemy: Renumber interrupts so irq_cpu can work.

one reserved interrupt on au1500 was missed. this broke the au1000 ethernet
driver.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide-generic: don't probe all legacy ISA IDE ports by default
  ide-cs: fix releasing I/O resources
  ide-cs: fix probing and add warm-plug support
  ide-pmac: remove bogus comment about pmac_ide_setup_device()
  ide-pmac: add ->cable_detect method
  ide-pmac: bugfix for media-bay support rework
  opti621: add PIO 4 support
  opti621: use pre-calculated PIO timings
  opti621: program devices timings separately in ->set_pio_mode
  opti621: use PCI clock value provided by controller
  opti621: remove DMA support
  opti621: disable read prefetch

lguest (in rusty's use-tun-ringfd patch) assumes that the
guest has updated its feature bits before setting its status
to VIRTIO_CONFIG_S_DRIVER_OK.

That's pretty reasonable, so let's make it so.
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We can't probe all legacy ISA IDE ports by default as the resources may be
occupied by other ISA devices.  Add "probe_mask" module parameter and probe
only first two ISA IDE ports by default leaving the decision about probing
the rest to the user (systems with ISA ide2-6 should be very, very rare).

This fixes a regression caused by:

commit 343a3451
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date:   Tue Jun 10 20:56:36 2008 +0200

    ide-generic: add missing hwif->chipset setup
...
Reported-by: NMikael Pettersson <mikpe@it.uu.se>
Bisected-by: NMikael Pettersson <mikpe@it.uu.se>
Tested-by: NMikael Pettersson <mikpe@it.uu.se>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

hwif content is already freed after ide_release() call so cache
hwif->io_ports.{data,ctl}_addr in local variables in ide_detach().

This fixes post-2.6.25 regression.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Fix probing by using ide_port_scan() and moving "retry loop"
  from ide_config() to idecs_register().

* Don't fail probe if there are no devices attached to a port.

* Remove (now redundant) error message from ide_config().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->cable_detect method and remove no longer needed pmif->cable_80 flag
(there is also no need to mask ->udma_mask now).

This fixes:

- forced ignoring of cable detection (needed for some CF devices & debug)

- cable detection for warm-plug

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix bug introduced by:

commit 2dde7861
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date:   Fri Apr 18 00:46:23 2008 +0200

    ide: rework PowerMac media-bay support (take 2)
...

[ Yeah, I suck. ]

bay->cd_index shouldn't be changed if IDE devices are not present
or retry operations won't happen.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add PIO 4 support.

While at it:

* Use a single struct ide_port_info instance for OPTi621 and OPTi621X.

Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: NJuergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use pre-calculated PIO timings in ->set_pio_mode.

* Remove no longer needed compute_clocks(), cmpt_clk(), struct pio_clocks_s,
  PIO_* defines and OPTI621_DEBUG define.

There should be no functional changes caused by this patch.

Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: NJuergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Set drive->drive_data to 'pio + XFER_PIO_0' instead of 'pio',
  then simplify selecting maximum adress setup timing.

* Remove no longer needed compute_pios() and opti621_port_init_devs().

* Program devices timings separately in ->set_pio_mode.

Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: NJuergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use PCI clock value provided by controller instead of depending on
a default (or user supplied) value.

Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: NJuergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

These controllers don't support DMA.

Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: NJuergen Kosel <juergen.kosel@gmx.de>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This fixes 2.6.25 regression (kernel.org bugzilla bug #10723) caused by:

commit 912fb29a
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date:   Fri Oct 19 00:30:11 2007 +0200

    opti621: always tune PIO
...

Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Bisected-by: NJuergen Kosel <juergen.kosel@gmx.de>
Tested-by: NJuergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: fixup write combine comment in pci_mmap_resource
  x86: PAT export resource_wc in pci sysfs
  x86, pci-dma.c: don't always add __GFP_NORETRY to gfp
  suspend-vs-iommu: prevent suspend if we could not resume
  x86: pci-dma.c: use __GFP_NO_OOM instead of __GFP_NORETRY
  pci, x86: add workaround for bug in ASUS A7V600 BIOS (rev 1005)
  PCI: use dev_to_node in pci_call_probe
  PCI: Correct last two HP entries in the bfsort whitelist

* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
  parisc: update my email address
  parisc: fix miscompilation of ip_fast_csum with gcc >= 4.3
  parisc: fix off by one in setup_sigcontext32
  parisc: export empty_zero_page
  parisc: export copy_user_page_asm
  parisc: move head.S to head.text section
  Revert "parisc: fix trivial section name warnings"

Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

ip_fast_csum needs an asm "memory" clobber, otherwise the aggressive
optimizations in gcc-4.3 cause it to be miscompiled.
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

Thankfully, the values were irrelevant... Spotted by
newer gcc.
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

Needed by ext4 when built as a module.
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

Needed by fuse (via copy_highpage).
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

And explicitly list it in vmlinux.lds...
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>