In bond 4, when the link goes down and up repeatedly, the bond may get an
unknown speed, and then this port can not work.

The driver notify netif_carrier_on() before update the link state, when the
bond receive carrier on, will query the speed of the port, if the query
operation happens before updating the link state, will get an unknown
speed. So need to notify netif_carrier_on() after update the link state.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

After the cmdq registers are cleared, the firmware may take time to
clear out possible left over commands in the cmdq. Driver must release
cmdq memory only after firmware has completed processing of left over
commands.

Fixes: 232d0d55 ("net: hns3: uninitialize command queue while unloading PF driver")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

If a PF is bonded to a virtual machine and the virtual machine exits
unexpectedly, some hardware resource cannot be cleared. In this case,
loading driver may cause exceptions. Therefore, the hardware resource
needs to be cleared when the driver is loaded.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

When adapter init fails, the blocked freelist bitmap is already freed
up and should not be touched. So, move the bitmap zeroing closer to
where it was successfully allocated. Also handle adapter init failure
unwind path immediately and avoid setting up RDMA memory windows.

Fixes: 5b377d11 ("cxgb4: Add debugfs facility to inject FL starvation")
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thanks to Kees Cook who detected the problem of memset that starting
from not the first member, but sized for the whole struct.
The better change will be to remove the redundant memset and to clear
only the msix_cnt member.
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Reported-by: NKees Cook <keescook@chromium.org>
Reviewed-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ensure a valid XSK buffer before proceed to free the xdp buffer.

The following kernel panic is observed without this patch:

RIP: 0010:xp_free+0x5/0x40
Call Trace:
stmmac_napi_poll_rxtx+0x332/0xb30 [stmmac]
? stmmac_tx_timer+0x3c/0xb0 [stmmac]
net_rx_action+0x13d/0x3d0
__do_softirq+0xfc/0x2fb
? smpboot_register_percpu_thread+0xe0/0xe0
run_ksoftirqd+0x32/0x70
smpboot_thread_fn+0x1d8/0x2c0
kthread+0x169/0x1a0
? kthread_park+0x90/0x90
ret_from_fork+0x1f/0x30
---[ end trace 0000000000000002 ]---

Fixes: bba2556e ("net: stmmac: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.13.x
Suggested-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NSong Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After free xsk_pool, there is possibility that napi polling is still
running in the middle, thus causes a kernel crash due to kernel NULL
pointer dereference of rx_q->xsk_pool and tx_q->xsk_pool.

Fix this by changing the XDP pool setup sequence to:
 1. disable napi before free xsk_pool
 2. enable napi after init xsk_pool

The following kernel panic is observed without this patch:

RIP: 0010:xsk_uses_need_wakeup+0x5/0x10
Call Trace:
stmmac_napi_poll_rxtx+0x3a9/0xae0 [stmmac]
__napi_poll+0x27/0x130
net_rx_action+0x233/0x280
__do_softirq+0xe2/0x2b6
run_ksoftirqd+0x1a/0x20
smpboot_thread_fn+0xac/0x140
? sort_range+0x20/0x20
kthread+0x124/0x150
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
---[ end trace a77c8956b79ac107 ]---

Fixes: bba2556e ("net: stmmac: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.13.x
Signed-off-by: NSong Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

macb_ptp_desc will not return NULL under most circumstances with correct
Kconfig and IP design config register. But for the sake of the extreme
corner case, check for NULL when using the helper. In case of rx_tstamp,
no action is necessary except to return (similar to timestamp disabled)
and warn. In case of TX, return -EINVAL to let the skb be free. Perform
this check before marking skb in progress.
Fixes coverity warning:
(4) Event dereference:
Dereferencing a null pointer "desc_ptp"
Signed-off-by: NHarini Katakam <harini.katakam@xilinx.com>
Reviewed-by: NRadhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 2c896fb0
"net: stmmac: dwmac-rk: add pd_gmac support for rk3399" and fixes
unbalanced pm_runtime_enable warnings.

In the commit to be reverted, support for power management was
introduced to the Rockchip glue code. Later, power management support
was introduced to the stmmac core code, resulting in multiple
invocations of pm_runtime_{enable,disable,get_sync,put_sync}.

The multiple invocations happen in rk_gmac_powerup and
stmmac_{dvr_probe, resume} as well as in rk_gmac_powerdown and
stmmac_{dvr_remove, suspend}, respectively, which are always called
in conjunction.

Fixes: 5ec55823 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: NMichael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For VFs we should return with an error in case we didn't get the exact
number of msix vectors as we requested.
Not doing that will lead to a crash when starting queues for this VF.
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to Armada XP datasheet bit at 0 position is corresponding for
TxInProg indication.

Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: NMaxim Kiselev <bigunclemax@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the case of taprio offload is not enabled, the error handling path
causes a kernel crash due to kernel NULL pointer deference.

Fix this by adding check for NULL before attempt to access 'plat->est'
on the mutex_lock() call.

The following kernel panic is observed without this patch:

RIP: 0010:mutex_lock+0x10/0x20
Call Trace:
tc_setup_taprio+0x482/0x560 [stmmac]
kmem_cache_alloc_trace+0x13f/0x490
taprio_disable_offload.isra.0+0x9d/0x180 [sch_taprio]
taprio_destroy+0x6c/0x100 [sch_taprio]
qdisc_create+0x2e5/0x4f0
tc_modify_qdisc+0x126/0x740
rtnetlink_rcv_msg+0x12b/0x380
_raw_spin_lock_irqsave+0x19/0x40
_raw_spin_unlock_irqrestore+0x18/0x30
create_object+0x212/0x340
rtnl_calcit.isra.0+0x110/0x110
netlink_rcv_skb+0x50/0x100
netlink_unicast+0x191/0x230
netlink_sendmsg+0x243/0x470
sock_sendmsg+0x5e/0x60
____sys_sendmsg+0x20b/0x280
copy_msghdr_from_user+0x5c/0x90
__mod_memcg_state+0x87/0xf0
 ___sys_sendmsg+0x7c/0xc0
lru_cache_add+0x7f/0xa0
_raw_spin_unlock+0x16/0x30
wp_page_copy+0x449/0x890
handle_mm_fault+0x921/0xfc0
__sys_sendmsg+0x59/0xa0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
---[ end trace b1f19b24368a96aa ]---

Fixes: b60189e0 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: NWong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A successful 'xge_mdio_config()' call should be balanced by a corresponding
'xge_mdio_remove()' call in the error handling path of the probe, as
already done in the remove function.

Update the error handling path accordingly.

Fixes: ea8ab16a ("drivers: net: xgene-v2: Add MDIO support")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit a955318f ("stmmac: align RX buffers"),
which breaks at least one platform (Nvidia Jetson-X1), causing
packet corruption. This is 100% reproducible, and reverting
the patch results in a working system again.

Given that it is "only" a performance optimisation, let's
return to a known working configuration until we can have a
good understanding of what is happening here.

Fixes: a955318f ("stmmac: align RX buffers")
Cc: Matteo Croce <mcroce@linux.microsoft.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Link: https://lore.kernel.org/netdev/871r71azjw.wl-maz@kernel.orgSigned-off-by: NMarc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210820183002.457226-1-maz@kernel.orgSigned-off-by: NJakub Kicinski <kuba@kernel.org>

On new platforms, the NVM is read-only. Attempting to update the NVM
is causing a lockup to occur. Do not attempt to write to the NVM
on platforms where it's not supported.
Emit an error message when the NVM checksum is invalid.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213667
Fixes: fb776f5d ("e1000e: Add support for Tiger Lake")
Suggested-by: NDima Ruinskiy <dima.ruinskiy@intel.com>
Suggested-by: NVitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NDvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

We should decode the latency and the max_latency before directly compare.
The latency should be presented as lat_enc = scale x value:
lat_enc_d = (lat_enc & 0x0x3ff) x (1U << (5*((max_ltr_enc & 0x1c00)
>> 10)))

Fixes: cf8fb73c ("e1000e: add support for LTR on I217/I218")
Suggested-by: NYee Li <seven.yi.lee@gmail.com>
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NDvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Use num_tx_queues rather than the IGC_MAX_TX_QUEUES fixed number 4 when
iterating over tx_ring queue since instantiated queue count could be
less than 4 where on-line cpu count is less than 4.

Fixes: ec50a9d4 ("igc: Add support for taprio offloading")
Signed-off-by: NToshiki Nishioka <toshiki.nishioka@intel.com>
Signed-off-by: NMuhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: NMuhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: NSasha Neftin <sasha.neftin@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

After unplug thunderbolt dock with i225, pciehp interrupt is triggered,
remove call will read/write mmio address which is already disconnected,
then cause page fault and make system hang.

Check PCI state to remove device safely.

Trace:
BUG: unable to handle page fault for address: 000000000000b604
Oops: 0000 [#1] SMP NOPTI
RIP: 0010:igc_rd32+0x1c/0x90 [igc]
Call Trace:
igc_ptp_suspend+0x6c/0xa0 [igc]
igc_ptp_stop+0x12/0x50 [igc]
igc_remove+0x7f/0x1c0 [igc]
pci_device_remove+0x3e/0xb0
__device_release_driver+0x181/0x240

Fixes: 13b5b7fd ("igc: Add support for Tx/Rx rings")
Fixes: b03c49cd ("igc: Save PTP time before a reset")
Signed-off-by: NAaron Ma <aaron.ma@canonical.com>
Tested-by: NDvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The devlink dev info command reports version information about the
device and firmware running on the board. This includes the "board.id"
field which is supposed to represent an identifier of the board design.
The ice driver uses the Product Board Assembly identifier for this.

In some cases, the PBA is not present in the NVM. If this happens,
devlink dev info will fail with an error. Instead, modify the
ice_info_pba function to just exit without filling in the context
buffer. This will cause the board.id field to be skipped. Log a dev_dbg
message in case someone wants to confirm why board.id is not showing up
for them.

Fixes: e961b679 ("ice: add board identifier info to devlink .info_get")
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20210819223451.245613-1-anthony.l.nguyen@intel.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Currently dpaa2_switch_takedown has a funny name and does not do the
opposite of dpaa2_switch_init, which makes probing fail when we need to
handle an -EPROBE_DEFER.

A sketch of what dpaa2_switch_init does:

	dpsw_open

	dpaa2_switch_detect_features

	dpsw_reset

	for (i = 0; i < ethsw->sw_attr.num_ifs; i++) {
		dpsw_if_disable

		dpsw_if_set_stp

		dpsw_vlan_remove_if_untagged

		dpsw_if_set_tci

		dpsw_vlan_remove_if
	}

	dpsw_vlan_remove

	alloc_ordered_workqueue

	dpsw_fdb_remove

	dpaa2_switch_ctrl_if_setup

When dpaa2_switch_takedown is called from the error path of
dpaa2_switch_probe(), the control interface, enabled by
dpaa2_switch_ctrl_if_setup from dpaa2_switch_init, remains enabled,
because dpaa2_switch_takedown does not call
dpaa2_switch_ctrl_if_teardown.

Since dpaa2_switch_probe might fail due to EPROBE_DEFER of a PHY, this
means that a second probe of the driver will happen with the control
interface directly enabled.

This will trigger a second error:

[   93.273528] fsl_dpaa2_switch dpsw.0: dpsw_ctrl_if_set_pools() failed
[   93.281966] fsl_dpaa2_switch dpsw.0: fsl_mc_driver_probe failed: -13
[   93.288323] fsl_dpaa2_switch: probe of dpsw.0 failed with error -13

Which if we investigate the /dev/dpaa2_mc_console log, we find out is
caused by:

[E, ctrl_if_set_pools:2211, DPMNG]  ctrl_if must be disabled

So make dpaa2_switch_takedown do the opposite of dpaa2_switch_init (in
reasonable limits, no reason to change STP state, re-add VLANs etc), and
rename it to something more conventional, like dpaa2_switch_teardown.

Fixes: 613c0a58 ("staging: dpaa2-switch: enable the control interface")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20210819141755.1931423-1-vladimir.oltean@nxp.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Make changes to MAC address dependent on the response of PF.
Disallow changes to HW MAC address and MAC filter from untrusted
VF, thanks to that ping is not lost if VF tries to change MAC.
Add a new field in iavf_mac_filter, to indicate whether there
was response from PF for given filter. Based on this field pass
or discard the filter.
If untrusted VF tried to change it's address, it's not changed.
Still filter was changed, because of that ping couldn't go through.

Fixes: c5c922b3 ("iavf: fix MAC address setting for VFs when filter is rejected")
Signed-off-by: NPrzemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: NSylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: NMateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: NGurucharan G <Gurucharanx.g@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Without this patch, ATR does not work. Receive/transmit uses queue
selection based on SW DCB hashing method.

If traffic classes are not configured for PF, then use
netdev_pick_tx function for selecting queue for packet transmission.
Instead of calling i40e_swdcb_skb_tx_hash, call netdev_pick_tx,
which ensures that packet is transmitted/received from CPU that is
running the application.

Reproduction steps:
1. Load i40e driver
2. Map each MSI interrupt of i40e port for each CPU
3. Disable ntuple, enable ATR i.e.:
ethtool -K $interface ntuple off
ethtool --set-priv-flags $interface flow-director-atr
4. Run application that is generating traffic and is bound to a
single CPU, i.e.:
taskset -c 9 netperf -H 1.1.1.1 -t TCP_RR -l 10
5. Observe behavior:
Application's traffic should be restricted to the CPU provided in
taskset.

Fixes: 89ec1f08 ("i40e: Fix queue-to-TC mapping on Tx")
Signed-off-by: NPrzemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: NArkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: NDave Switzer <david.switzer@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Currently we are unable to ping a bridge on top of a felix switch which
uses the ocelot-8021q tagger. The packets are dropped on the ingress of
the user port and the 'drop_local' counter increments (the counter which
denotes drops due to no valid destinations).

Dumping the PGID tables, it becomes clear that the PGID_SRC of the user
port is zero, so it has no valid destinations.

But looking at the code, the cpu_fwd_mask (the bit mask of DSA tag_8021q
ports) is clearly missing from the forwarding mask of ports that are
under a bridge. So this has always been broken.

Looking at the version history of the patch, in v7
https://patchwork.kernel.org/project/netdevbpf/patch/20210125220333.1004365-12-olteanv@gmail.com/
the code looked like this:

	/* Standalone ports forward only to DSA tag_8021q CPU ports */
	unsigned long mask = cpu_fwd_mask;

(...)
	} else if (ocelot->bridge_fwd_mask & BIT(port)) {
		mask |= ocelot->bridge_fwd_mask & ~BIT(port);

while in v8 (the merged version)
https://patchwork.kernel.org/project/netdevbpf/patch/20210129010009.3959398-12-olteanv@gmail.com/
it looked like this:

	unsigned long mask;

(...)
	} else if (ocelot->bridge_fwd_mask & BIT(port)) {
		mask = ocelot->bridge_fwd_mask & ~BIT(port);

So the breakage was introduced between v7 and v8 of the patch.

Fixes: e21268ef ("net: dsa: felix: perform switch setup for tag_8021q")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210817160425.3702809-1-vladimir.oltean@nxp.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

In ixgbe_xsk_pool_enable(), if ixgbe_xsk_wakeup() fails,
We should restore the previous state and clean up the
resources. Add the missing clear af_xdp_zc_qps and unmap dma
to fix this bug.

Fixes: d49e286d ("ixgbe: add tracking of AF_XDP zero-copy state for each queue pair")
Fixes: 4a9b32f3 ("ixgbe: fix potential RX buffer starvation for AF_XDP")
Signed-off-by: NWang Hai <wanghai38@huawei.com>
Acked-by: NMagnus Karlsson <magnus.karlsson@intel.com>
Tested-by: NSandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20210817203736.3529939-1-anthony.l.nguyen@intel.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

qlcnic_83xx_unlock_flash() is called on all paths after we call
qlcnic_83xx_lock_flash(), except for one error path on failure
of QLCRD32(), which may cause a deadlock. This bug is suggested
by a static analysis tool, please advise.

Fixes: 81d0aeb0 ("qlcnic: flash template based firmware reset recovery")
Signed-off-by: NDinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20210816131405.24024-1-dinghao.liu@zju.edu.cnSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Each completion ring entry has a valid bit to indicate that the entry
contains a valid completion event.  The driver's main poll loop
__bnxt_poll_work() has the proper dma_rmb() to make sure the valid
bit of the next entry has been checked before proceeding further.
But when we call bnxt_rx_pkt() to process the RX event, the RX
completion event consists of two completion entries and only the
first entry has been checked to be valid.  We need the same barrier
after checking the next completion entry.  Add missing dma_rmb()
barriers in bnxt_rx_pkt() and other similar locations.

Fixes: 67a95e20 ("bnxt_en: Need memory barrier when processing the completion ring.")
Reported-by: NLance Richardson <lance.richardson@broadcom.com>
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Reviewed-by: NLance Richardson <lance.richardson@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

212 firmware broke aRFS, so disable it.  Traffic may stop after ntuple
filters are inserted and deleted by the 212 firmware.

Fixes: ae10ae74 ("bnxt_en: Add new hardware RFS mode.")
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a possible null-pointer dereference in qed_rdma_create_qp().

Changes from V2:
- Revert checkpatch fixes.
Reported-by: NTOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoiding qed ll2 race condition and NULL pointer dereference as part
of the remove and recovery flows.

Changes form V1:
- Change (!p_rx->set_prod_addr).
- qed_ll2.c checkpatch fixes.

Change from V2:
- Revert "qed_ll2.c checkpatch fixes".
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Internal tests found out that the latest code doesn't bring up 1PPS out
as expected. As a result of incorrect define used to round the time up
the time was round down to the past second boundary.

Fix define used for rounding to properly round up to the next Top of
second in ice_ptp_cfg_clkout to fix it.

Fixes: 172db5f9 ("ice: add support for auxiliary input/output pins")
Signed-off-by: NMaciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: NSunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20210813165018.2196013-1-anthony.l.nguyen@intel.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Drivers should count packets they are dropping.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: NMichael Chan <michael.chan@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

skbs are freed on error and not put on the ring. We may, however,
be in a situation where we're freeing the last skb of a batch,
and there is a doorbell ring pending because of xmit_more() being
true earlier. Make sure we ring the door bell in such situations.

Since errors are rare don't pay attention to xmit_more() and just
always flush the pending frames.

The busy case should be safe to be left alone because it can
only happen if start_xmit races with completions and they
both enable the queue. In that case the kick can't be pending.

Noticed while reading the code.

Fixes: 4d172f21 ("bnxt_en: Implement xmit_more.")
Reviewed-by: NMichael Chan <michael.chan@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

napi schedules DIM, napi has to be disabled first,
then DIM canceled.

Noticed while reading the code.

Fixes: 0bc0b97f ("bnxt_en: cleanup DIM work on device shutdown")
Fixes: 6a8788f2 ("bnxt_en: add support for software dynamic interrupt moderation")
Reviewed-by: NMichael Chan <michael.chan@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

We can't take the tx lock from the napi poll routine, because
netpoll can poll napi at any moment, including with the tx lock
already held.

The tx lock is protecting against two paths - the disable
path, and (as Michael points out) the NETDEV_TX_BUSY case
which may occur if NAPI completions race with start_xmit
and both decide to re-enable the queue.

For the disable/ifdown path use synchronize_net() to make sure
closing the device does not race we restarting the queues.
Annotate accesses to dev_state against data races.

For the NAPI cleanup vs start_xmit path - appropriate barriers
are already in place in the main spot where Tx queue is stopped
but we need to do the same careful dance in the TX_BUSY case.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: NMichael Chan <michael.chan@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The ocelot driver makes use of regmap, wrapping it with driver specific
operations that are thin wrappers around the core regmap APIs. These are
exported with EXPORT_SYMBOL, dropping the _GPL from the core regmap
exports which is frowned upon. Add _GPL suffixes to at least the APIs that
are doing register I/O.
Signed-off-by: NMark Brown <broonie@kernel.org>
Acked-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: switchdev: zero-initialize struct switchdev_notifier_fdb_info emitted by drivers towards the bridge

The blamed commit added a new field to struct switchdev_notifier_fdb_info,
but did not make sure that all call paths set it to something valid.
For example, a switchdev driver may emit a SWITCHDEV_FDB_ADD_TO_BRIDGE
notifier, and since the 'is_local' flag is not set, it contains junk
from the stack, so the bridge might interpret those notifications as
being for local FDB entries when that was not intended.

To avoid that now and in the future, zero-initialize all
switchdev_notifier_fdb_info structures created by drivers such that all
newly added fields to not need to touch drivers again.

Fixes: 2c4eca3e ("net: bridge: switchdev: include local flag in FDB notifications")
Reported-by: NIdo Schimmel <idosch@idosch.org>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NIdo Schimmel <idosch@nvidia.com>
Tested-by: NIdo Schimmel <idosch@nvidia.com>
Reviewed-by: NLeon Romanovsky <leonro@nvidia.com>
Reviewed-by: NKarsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20210810115024.1629983-1-vladimir.oltean@nxp.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Check return value of mlx5_fw_tracer_start(), set error path and fix
return value of mlx5_fw_tracer_init() accordingly.

Fixes: c71ad41c ("net/mlx5: FW tracer, events handling")
Signed-off-by: NAya Levin <ayal@nvidia.com>
Reviewed-by: NMoshe Shemesh <moshe@nvidia.com>
Reviewed-by: NTariq Toukan <tariqt@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

The CQ destroy is performed based on the IRQ number that is stored in
cq->irqn. That number wasn't set explicitly during CQ creation and as
expected some of the API users of mlx5_core_create_cq() forgot to update
it.

This caused to wrong synchronization call of the wrong IRQ with a number
0 instead of the real one.

As a fix, set the IRQ number directly in the mlx5_core_create_cq() and
update all users accordingly.

Fixes: 1a86b377 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Fixes: ef1659ad ("IB/mlx5: Add DEVX support for CQ events")
Signed-off-by: NShay Drory <shayd@nvidia.com>
Reviewed-by: NTariq Toukan <tariqt@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Free the offload sample action on error.

Fixes: f94d6389 ("net/mlx5e: TC, Add support to offload sample action")
Signed-off-by: NChris Mi <cmi@nvidia.com>
Reviewed-by: NOz Shlomo <ozsh@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Destroy pool->mutex when we destroy the pool.

Fixes: c36326d3 ("net/mlx5: Round-Robin EQs over IRQs")
Signed-off-by: NShay Drory <shayd@nvidia.com>
Reviewed-by: NParav Pandit <parav@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>