The report descriptor is read by user space (via the Service
Discovery Protocol), so it is only available during the ioctl
to connect. However, the HID probe function that needs the
descriptor might not be called until a specific module is
loaded. Keep a copy of the descriptor so it is available for
later use.
Signed-off-by: NMichael Poole <mdpoole@troilus.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When in sniff mode with a long interval time (1.28s) it can take 4+ seconds
to establish a SCO link. Fix by requesting active mode before requesting
SCO connection. This improves SCO setup time to ~500ms.

Bluetooth headsets that use a long interval time, and exhibit the long
SCO connection time include Motorola H790, HX1 and H17. They have a
CSR 2.1 chipset.

Verified this behavior and fix with host Bluetooth chipsets: BCM4329 and
TI1271.

2009-10-13 14:17:46.183722 > HCI Event: Mode Change (0x14) plen 6
    status 0x00 handle 1 mode 0x02 interval 2048
    Mode: Sniff
2009-10-13 14:17:53.436285 < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
    handle 1 voice setting 0x0060
2009-10-13 14:17:53.445593 > HCI Event: Command Status (0x0f) plen 4
    Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
2009-10-13 14:17:57.788855 > HCI Event: Synchronous Connect Complete 0x2c) plen 17
    status 0x00 handle 257 bdaddr 00:1A:0E:F1:A4:7F type eSCO
    Air mode: CVSD
Signed-off-by: NNick Pelly <npelly@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When processing a RFCOMM UA frame when the socket is closed and we were
not the RFCOMM initiator would cause rfcomm_session_put() to be called
twice during rfcomm_process_rx(). This would cause a kernel panic in
rfcomm_session_close() then.

This could be easily reproduced during disconnect with devices such as
Motorola H270 that send RFCOMM UA followed quickly by L2CAP disconnect
request. This trace for this looks like:

2009-09-21 17:22:37.788895 < ACL data: handle 1 flags 0x02 dlen 8
   L2CAP(d): cid 0x0041 len 4 [psm 3]
     RFCOMM(s): DISC: cr 0 dlci 20 pf 1 ilen 0 fcs 0x7d
2009-09-21 17:22:37.906204 > HCI Event: Number of Completed Packets (0x13) plen 5
   handle 1 packets 1
2009-09-21 17:22:37.933090 > ACL data: handle 1 flags 0x02 dlen 8
   L2CAP(d): cid 0x0040 len 4 [psm 3]
     RFCOMM(s): UA: cr 0 dlci 20 pf 1 ilen 0 fcs 0x57
2009-09-21 17:22:38.636764 < ACL data: handle 1 flags 0x02 dlen 8
   L2CAP(d): cid 0x0041 len 4 [psm 3]
     RFCOMM(s): DISC: cr 0 dlci 0 pf 1 ilen 0 fcs 0x9c
2009-09-21 17:22:38.744125 > HCI Event: Number of Completed Packets (0x13) plen 5
   handle 1 packets 1
2009-09-21 17:22:38.763687 > ACL data: handle 1 flags 0x02 dlen 8
   L2CAP(d): cid 0x0040 len 4 [psm 3]
     RFCOMM(s): UA: cr 0 dlci 0 pf 1 ilen 0 fcs 0xb6
2009-09-21 17:22:38.783554 > ACL data: handle 1 flags 0x02 dlen 12
   L2CAP(s): Disconn req: dcid 0x0040 scid 0x0041

Avoid calling rfcomm_session_put() twice by skipping this call
in rfcomm_recv_ua() if the socket is closed.
Signed-off-by: NNick Pelly <npelly@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

With the commit 9e726b17 the
rfcomm_session_put() gets accidentially called from a timeout
callback and results in this:

BUG: sleeping function called from invalid context at net/core/sock.c:1897
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper
Pid: 0, comm: swapper Tainted: P           2.6.32 #31
Call Trace:
 <IRQ>  [<ffffffff81036455>] __might_sleep+0xf8/0xfa
 [<ffffffff8138ef1d>] lock_sock_nested+0x29/0xc4
 [<ffffffffa03921b3>] lock_sock+0xb/0xd [l2cap]
 [<ffffffffa03948e6>] l2cap_sock_shutdown+0x1c/0x76 [l2cap]
 [<ffffffff8106adea>] ? clockevents_program_event+0x75/0x7e
 [<ffffffff8106bea2>] ? tick_dev_program_event+0x37/0xa5
 [<ffffffffa0394967>] l2cap_sock_release+0x27/0x67 [l2cap]
 [<ffffffff8138c971>] sock_release+0x1a/0x67
 [<ffffffffa03d2492>] rfcomm_session_del+0x34/0x53 [rfcomm]
 [<ffffffffa03d24c5>] rfcomm_session_put+0x14/0x16 [rfcomm]
 [<ffffffffa03d28b4>] rfcomm_session_timeout+0xe/0x1a [rfcomm]
 [<ffffffff810554a8>] run_timer_softirq+0x1e2/0x29a
 [<ffffffffa03d28a6>] ? rfcomm_session_timeout+0x0/0x1a [rfcomm]
 [<ffffffff8104e0f6>] __do_softirq+0xfe/0x1c5
 [<ffffffff8100e8ce>] ? timer_interrupt+0x1a/0x21
 [<ffffffff8100cc4c>] call_softirq+0x1c/0x28
 [<ffffffff8100e05b>] do_softirq+0x33/0x6b
 [<ffffffff8104daf6>] irq_exit+0x36/0x85
 [<ffffffff8100d7a9>] do_IRQ+0xa6/0xbd
 [<ffffffff8100c493>] ret_from_intr+0x0/0xa
 <EOI>  [<ffffffff812585b3>] ? acpi_idle_enter_bm+0x269/0x294
 [<ffffffff812585a9>] ? acpi_idle_enter_bm+0x25f/0x294
 [<ffffffff81373ddc>] ? cpuidle_idle_call+0x97/0x107
 [<ffffffff8100aca0>] ? cpu_idle+0x53/0xaa
 [<ffffffff81429006>] ? rest_init+0x7a/0x7c
 [<ffffffff8177bc8c>] ? start_kernel+0x389/0x394
 [<ffffffff8177b29c>] ? x86_64_start_reservations+0xac/0xb0
 [<ffffffff8177b384>] ? x86_64_start_kernel+0xe4/0xeb

To fix this, the rfcomm_session_put() needs to be moved out of
rfcomm_session_timeout() into rfcomm_process_sessions(). In that
context it is perfectly fine to sleep and disconnect the socket.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Tested-by: NDavid John <davidjon@xenontk.org>

General Motors carkits that use LGE BT chipsets return this error code
when an eSCO is attempted, despite advertising eSCO support.

2009-08-13 14:41:39.755518 < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
   handle 1 voice setting 0x0060
2009-08-13 14:41:39.757563 > HCI Event: Command Status (0x0f) plen 4
   Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
2009-08-13 14:41:39.789484 > HCI Event: Synchronous Connect Complete (0x2c) plen 17
   status 0x1a handle 257 bdaddr 00:1E:B2:23:5E:B3 type eSCO
   Error: Unsupported Remote Feature / Unsupported LMP Feature
Signed-off-by: NJaikumar Ganesh <jaikumar@google.com>
Signed-off-by: NNick Pelly <npelly@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In commit 2da31939, support
for Bluetooth hid_output_raw_report was added, but it pushes
the data to the interrupt channel instead of the contol one.

This patch makes hid_output_raw_report use the control channel
instead. Using the interrupt channel was a mistake.
Signed-off-by: NBastien Nocera <hadess@hadess.net>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Move skb_clone after error confition check so it is not going
potentially out of the scope.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Trivial fix for double free of SKB pointer with kfree_skb to
make code simplier and cleaner. Remove unused variable err.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Convert code away from ->read_proc/->write_proc interfaces.  Switch to
proc_create()/proc_create_data() which make addition of proc entries
reliable wrt NULL ->proc_fops, NULL ->data and so on.

Problem with ->read_proc et al is described here commit
786d7e16 "Fix rmmod/read/write races in
/proc entries"

[akpm@linux-foundation.org: CONFIG_PROC_FS=n build fix]
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When locking was introduced the error path branch was not taken
into account. Error was found in sparse code checking. Kudos to
Jani Nikula.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: NGustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Moving the Ack to before l2cap_retransmit_frame() we can avoid the
case where txWindow is full and the packet can't be retransmited.
Signed-off-by: NGustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

RemoteBusy flag need to be unset before l2cap_ertm_send(), otherwise
l2cap_ertm_send() will return without sending packets because it checks
that flag before start sending.
Signed-off-by: NGustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Return the PTR_ERR of the correct pointer.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

fix some typos and punctuation in comments
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

By default the RFCOMM layer would still use L2CAP basic mode. For testing
purposes this option enables RFCOMM to select enhanced retransmission
mode.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

For testing purposes it is important to modify the max transmit value.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

SendRRorRNR needs to acknowledge received I-frames (actually every packet
needs to acknowledge received I-frames by sending the proper packet
sequence number), so ReqSeq is set to the next I-frame number sequence to
be pulled by the reassembly function.
SendRRorRNR tells the remote side about local busy conditions, it sends
a Receiver Ready frame if local busy is false or a Receiver Not Ready
if local busy is true.
ReqSeq is the packet's field to send the number of the acknowledged
packets.
Signed-off-by: NGustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

RejActioned is used to prevent retransmission when a entity is on the
WAIT_F state, i.e., waiting for a frame with F-bit set due local busy
condition or a expired retransmission timer. (When these two events raise
they send a frame with the Poll bit set and enters in the WAIT_F state to
wait for a frame with the Final bit set.)
The local entity doesn't send I-frames(the data frames) until the receipt
of a frame with F-bit set. When that happens it also set RejActioned to false.
RejActioned is a mandatory feature of ERTM spec.
Signed-off-by: NGustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

As specified by ERTM spec an ERTM channel can acknowledge received
I-frames(the data frames) by sending an I-frame with the proper ReqSeq
value (i.e. ReqSeq is set to BufferSeq).  Until now we aren't setting the
ReqSeq value on I-frame control bits. That way we can save sending
S-frames(Supervise frames) only to acknowledge receipt of I-frames. It
is very helpful to the full-duplex channel.
ReqSeq is the packet sequence number sent in an acknowledgement frame to
acknowledge receipt of frames up to (ReqSeq - 1).
BufferSeq controls the receiver buffer, it is used to delay
acknowledgement of new frames to not cause buffer overflow. BufferSeq
value is not increased until frames are pulled by reassembly function.
Signed-off-by: NGustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

SrejActioned  is a flag that when set prevents local side to retransmit a
I-frame(the data frame) already retransmitted. The local entity can
retransmit again only when it receives a SREJ frame with the F-bit set.
SREJ frame - Selective Reject frame  - is sent when an entity wants the
retransmission of a specific I-frame that was lost or corrupted.
This bug can put ERTM in an unknown state once the entity can't
retransmit.
A frame with the Final bit set is expected when the local side sends a
frame with the Poll bit set due to a local busy condition or a
retransmission timer expired. (Receipt of P-bit shall always be replied by
a frame with the F-bit set).
pi->conn_state keeps informations about many ERTM flags including
SrejActioned.
Signed-off-by: NGustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Fix ERTM's full-duplex channel to work as specified by ERTM spec. ERTM
needs to handle state vars, timers and counters to send and receive
I-frames(the data frames), i.e., for both sides of data communication.
We initialize all of them to the default values here.
Full-duplex channel is a mandatory feature of ERTM spec.
Signed-off-by: NGustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

According to BNEP test specification the proper response should be sent
for a setup connection request message after the BNEP connection setup
has been completed.
Signed-off-by: NVikram Kandukuri <vikram.kandukuri@atheros.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The tasklet schedule function helpers are just an obfuscation. So remove
them and call the schedule functions directly.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

For future simplification it is important that the hci_recv_frame
function is no longer an inline function. So move it into the module
itself and export it.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Sending commands to a down interface results in a timeout while clearly
it should just return ENETDOWN. When using the ioctls this works fine,
but not when using the HCI sockets sendmsg interface.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Implement raw output callback which is used by hidraw to send raw data to
the underlying device.

Without this patch, the userspace hidraw-based applications can't send
output reports to HID Bluetooth devices.
Reported-and-tested-by: NBrian Gunn <bgunn@solekai.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Not including net/atm/

Compiled tested x86 allyesconfig only
Added a > 80 column line or two, which I ignored.
Existing checkpatch plaints willfully, cheerfully ignored.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Basic Mode is the default mode of operation of a L2CAP entity. In
this case the RFC (Retransmission and Flow Control) configuration
option should not be used at all.

Normally remote L2CAP implementation should just ignore this option,
but it can cause various side effects with other Bluetooth stacks
that are not capable of handling unknown options.
Signed-off-by: NGustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The default mode for SOCK_SEQPACKET is Basic Mode. So when no
mode has been specified, Basic Mode shall be used.

This is important for current application to keep working as
expected and not cause a regression.
Signed-off-by: NGustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch fixes double pairing issues with Secure Simple
Paring support. It was observed that when pairing with SSP
enabled, that the confirmation will be asked twice.

http://www.spinics.net/lists/linux-bluetooth/msg02473.html

This also causes bug when initiating SSP connection from
Windows Vista.

The reason is because bluetoothd does not store link keys
since HCIGETAUTHINFO returns 0. Setting default to general
bonding fixes these issues.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Before calling capable(CAP_NET_RAW) check if this operations is on behalf
of the kernel or on behalf of userspace.  Do not do the security check if
it is on behalf of the kernel.
Signed-off-by: NEric Paris <eparis@redhat.com>
Acked-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The generic __sock_create function has a kern argument which allows the
security system to make decisions based on if a socket is being created by
the kernel or by userspace.  This patch passes that flag to the
net_proto_family specific create function, so it can do the same thing.
Signed-off-by: NEric Paris <eparis@redhat.com>
Acked-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When shutdown ppp connection, lockdep waring about non-static key
will happen, it is caused by the lock is not initialized properly
at that time.

Fix with tuning the lock/skb_queue_head init order

[   94.339261] INFO: trying to register non-static key.
[   94.342509] the code is fine but needs lockdep annotation.
[   94.342509] turning off the locking correctness validator.
[   94.342509] Pid: 0, comm: swapper Not tainted 2.6.31-mm1 #2
[   94.342509] Call Trace:
[   94.342509]  [<c0248fbe>] register_lock_class+0x58/0x241
[   94.342509]  [<c024b5df>] ? __lock_acquire+0xb57/0xb73
[   94.342509]  [<c024ab34>] __lock_acquire+0xac/0xb73
[   94.342509]  [<c024b7fa>] ? lock_release_non_nested+0x17b/0x1de
[   94.342509]  [<c024b662>] lock_acquire+0x67/0x84
[   94.342509]  [<c04cd1eb>] ? skb_dequeue+0x15/0x41
[   94.342509]  [<c054a857>] _spin_lock_irqsave+0x2f/0x3f
[   94.342509]  [<c04cd1eb>] ? skb_dequeue+0x15/0x41
[   94.342509]  [<c04cd1eb>] skb_dequeue+0x15/0x41
[   94.342509]  [<c054a648>] ? _read_unlock+0x1d/0x20
[   94.342509]  [<c04cd641>] skb_queue_purge+0x14/0x1b
[   94.342509]  [<fab94fdc>] l2cap_recv_frame+0xea1/0x115a [l2cap]
[   94.342509]  [<c024b5df>] ? __lock_acquire+0xb57/0xb73
[   94.342509]  [<c0249c04>] ? mark_lock+0x1e/0x1c7
[   94.342509]  [<f8364963>] ? hci_rx_task+0xd2/0x1bc [bluetooth]
[   94.342509]  [<fab95346>] l2cap_recv_acldata+0xb1/0x1c6 [l2cap]
[   94.342509]  [<f8364997>] hci_rx_task+0x106/0x1bc [bluetooth]
[   94.342509]  [<fab95295>] ? l2cap_recv_acldata+0x0/0x1c6 [l2cap]
[   94.342509]  [<c02302c4>] tasklet_action+0x69/0xc1
[   94.342509]  [<c022fbef>] __do_softirq+0x94/0x11e
[   94.342509]  [<c022fcaf>] do_softirq+0x36/0x5a
[   94.342509]  [<c022fe14>] irq_exit+0x35/0x68
[   94.342509]  [<c0204ced>] do_IRQ+0x72/0x89
[   94.342509]  [<c02038ee>] common_interrupt+0x2e/0x34
[   94.342509]  [<c024007b>] ? pm_qos_add_requirement+0x63/0x9d
[   94.342509]  [<c038e8a5>] ? acpi_idle_enter_bm+0x209/0x238
[   94.342509]  [<c049d238>] cpuidle_idle_call+0x5c/0x94
[   94.342509]  [<c02023f8>] cpu_idle+0x4e/0x6f
[   94.342509]  [<c0534153>] rest_init+0x53/0x55
[   94.342509]  [<c0781894>] start_kernel+0x2f0/0x2f5
[   94.342509]  [<c0781091>] i386_start_kernel+0x91/0x96
Reported-by: NOliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: NDave Young <hidave.darkstar@gmail.com>
Tested-by: NOliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to driver core changes dev_set_drvdata will call kzalloc which should be
in might_sleep context, but hci_conn_add will be called in atomic context

Like dev_set_name move dev_set_drvdata to work queue function.

oops as following:

Oct  2 17:41:59 darkstar kernel: [  438.001341] BUG: sleeping function called from invalid context at mm/slqb.c:1546
Oct  2 17:41:59 darkstar kernel: [  438.001345] in_atomic(): 1, irqs_disabled(): 0, pid: 2133, name: sdptool
Oct  2 17:41:59 darkstar kernel: [  438.001348] 2 locks held by sdptool/2133:
Oct  2 17:41:59 darkstar kernel: [  438.001350]  #0:  (sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+.+.}, at: [<faa1d2f5>] lock_sock+0xa/0xc [l2cap]
Oct  2 17:41:59 darkstar kernel: [  438.001360]  #1:  (&hdev->lock){+.-.+.}, at: [<faa20e16>] l2cap_sock_connect+0x103/0x26b [l2cap]
Oct  2 17:41:59 darkstar kernel: [  438.001371] Pid: 2133, comm: sdptool Not tainted 2.6.31-mm1 #2
Oct  2 17:41:59 darkstar kernel: [  438.001373] Call Trace:
Oct  2 17:41:59 darkstar kernel: [  438.001381]  [<c022433f>] __might_sleep+0xde/0xe5
Oct  2 17:41:59 darkstar kernel: [  438.001386]  [<c0298843>] __kmalloc+0x4a/0x15a
Oct  2 17:41:59 darkstar kernel: [  438.001392]  [<c03f0065>] ? kzalloc+0xb/0xd
Oct  2 17:41:59 darkstar kernel: [  438.001396]  [<c03f0065>] kzalloc+0xb/0xd
Oct  2 17:41:59 darkstar kernel: [  438.001400]  [<c03f04ff>] device_private_init+0x15/0x3d
Oct  2 17:41:59 darkstar kernel: [  438.001405]  [<c03f24c5>] dev_set_drvdata+0x18/0x26
Oct  2 17:41:59 darkstar kernel: [  438.001414]  [<fa51fff7>] hci_conn_init_sysfs+0x40/0xd9 [bluetooth]
Oct  2 17:41:59 darkstar kernel: [  438.001422]  [<fa51cdc0>] ? hci_conn_add+0x128/0x186 [bluetooth]
Oct  2 17:41:59 darkstar kernel: [  438.001429]  [<fa51ce0f>] hci_conn_add+0x177/0x186 [bluetooth]
Oct  2 17:41:59 darkstar kernel: [  438.001437]  [<fa51cf8a>] hci_connect+0x3c/0xfb [bluetooth]
Oct  2 17:41:59 darkstar kernel: [  438.001442]  [<faa20e87>] l2cap_sock_connect+0x174/0x26b [l2cap]
Oct  2 17:41:59 darkstar kernel: [  438.001448]  [<c04c8df5>] sys_connect+0x60/0x7a
Oct  2 17:41:59 darkstar kernel: [  438.001453]  [<c024b703>] ? lock_release_non_nested+0x84/0x1de
Oct  2 17:41:59 darkstar kernel: [  438.001458]  [<c028804b>] ? might_fault+0x47/0x81
Oct  2 17:41:59 darkstar kernel: [  438.001462]  [<c028804b>] ? might_fault+0x47/0x81
Oct  2 17:41:59 darkstar kernel: [  438.001468]  [<c033361f>] ? __copy_from_user_ll+0x11/0xce
Oct  2 17:41:59 darkstar kernel: [  438.001472]  [<c04c9419>] sys_socketcall+0x82/0x17b
Oct  2 17:41:59 darkstar kernel: [  438.001477]  [<c020329d>] syscall_call+0x7/0xb
Signed-off-by: NDave Young <hidave.darkstar@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create a new socket level option to report number of queue overflows

Recently I augmented the AF_PACKET protocol to report the number of frames lost
on the socket receive queue between any two enqueued frames.  This value was
exported via a SOL_PACKET level cmsg.  AFter I completed that work it was
requested that this feature be generalized so that any datagram oriented socket
could make use of this option.  As such I've created this patch, It creates a
new SOL_SOCKET level option called SO_RXQ_OVFL, which when enabled exports a
SOL_SOCKET level cmsg that reports the nubmer of times the sk_receive_queue
overflowed between any two given frames.  It also augments the AF_PACKET
protocol to take advantage of this new feature (as it previously did not touch
sk->sk_drops, which this patch uses to record the overflow count).  Tested
successfully by me.

Notes:

1) Unlike my previous patch, this patch simply records the sk_drops value, which
is not a number of drops between packets, but rather a total number of drops.
Deltas must be computed in user space.

2) While this patch currently works with datagram oriented protocols, it will
also be accepted by non-datagram oriented protocols. I'm not sure if thats
agreeable to everyone, but my argument in favor of doing so is that, for those
protocols which aren't applicable to this option, sk_drops will always be zero,
and reporting no drops on a receive queue that isn't used for those
non-participating protocols seems reasonable to me.  This also saves us having
to code in a per-protocol opt in mechanism.

3) This applies cleanly to net-next assuming that commit
97775007 (my af packet cmsg patch) is reverted
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All usages of structure net_proto_ops should be declared const.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This provides safety against negative optlen at the type
level instead of depending upon (sometimes non-trivial)
checks against this sprinkled all over the the place, in
each and every implementation.

Based upon work done by Arjan van de Ven and feedback
from Linus Torvalds.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HID core registers input, hidraw and hiddev devices, but leaves
unregistering it up to the individual driver, which is not really nice.
Let's move all the logic to the core.
Reported-by: NMarcel Holtmann <marcel@holtmann.org>
Reported-by: NBrian Rogers <brian@xyzw.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Let attribute group vectors be declared "const".  We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.

To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.

  # cat /sys/class/net/wlan0/uevent
  DEVTYPE=wlan
  INTERFACE=wlan0
  IFINDEX=5

This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.

The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>