- 28 5月, 2013 31 次提交
-
-
由 Cong Wang 提交于
As Stephen proposed: Since bonding supports configuration via iproute (netlink) and sysfs, I think it is time to purge the old ifenslave code out of Documentation/networking and update the documentation. Suggested-by: NStephen Hemminger <stephen@networkplumber.org> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Jay Vosburgh <fubar@us.ibm.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: NCong Wang <amwang@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Masanari Iida 提交于
Correct spelling typo Signed-off-by: NMasanari Iida <standby24x7@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nikolay Aleksandrov 提交于
Since the xmit_hash_policy pointer is always valid and not dependent on anything, we can change it while the bond device is up and running. The only downside would be the out of order packets but that is a small price to pay. Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sachin Kamat 提交于
module_spi_driver() removes some boilerplate and makes the code simpler. Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 dingtianhong 提交于
The netpoll_rx_disable() will always return 0, it is no use and looks wordy, so remove the unnecessary code and get rid of it in _dev_open and _dev_close. Signed-off-by: NDing Tianhong <dingtianhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: netdev@vger.kernel.org Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Simon Horman says: ==================== In the case where a non-MPLS packet is received and an MPLS stack is added it may well be the case that the original skb is GSO but the NIC used for transmit does not support GSO of MPLS packets. The aim of this short series is to provide GSO in software for MPLS packets whose skbs are GSO. Change since v4: Update first patch of the series to use 16 bits for all *_headers rather than just inner_*_headers Simon Horman (2): net: Use 16bits for *_headers fields of struct skbuff MPLS: Add limited GSO support ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Simon Horman 提交于
In the case where a non-MPLS packet is received and an MPLS stack is added it may well be the case that the original skb is GSO but the NIC used for transmit does not support GSO of MPLS packets. The aim of this code is to provide GSO in software for MPLS packets whose skbs are GSO. SKB Usage: When an implementation adds an MPLS stack to a non-MPLS packet it should do the following to skb metadata: * Set skb->inner_protocol to the old non-MPLS ethertype of the packet. skb->inner_protocol is added by this patch. * Set skb->protocol to the new MPLS ethertype of the packet. * Set skb->network_header to correspond to the end of the L3 header, including the MPLS label stack. I have posted a patch, "[PATCH v3.29] datapath: Add basic MPLS support to kernel" which adds MPLS support to the kernel datapath of Open vSwtich. That patch sets the above requirements in datapath/actions.c:push_mpls() and was used to exercise this code. The datapath patch is against the Open vSwtich tree but it is intended that it be added to the Open vSwtich code present in the mainline Linux kernel at some point. Features: I believe that the approach that I have taken is at least partially consistent with the handling of other protocols. Jesse, I understand that you have some ideas here. I am more than happy to change my implementation. This patch adds dev->mpls_features which may be used by devices to advertise features supported for MPLS packets. A new NETIF_F_MPLS_GSO feature is added for devices which support hardware MPLS GSO offload. Currently no devices support this and MPLS GSO always falls back to software. Alternate Implementation: One possible alternate implementation is to teach netif_skb_features() and skb_network_protocol() about MPLS, in a similar way to their understanding of VLANs. I believe this would avoid the need for net/mpls/mpls_gso.c and in particular the calls to __skb_push() and __skb_push() in mpls_gso_segment(). I have decided on the implementation in this patch as it should not introduce any overhead in the case where mpls_gso is not compiled into the kernel or inserted as a module. MPLS GSO suggested by Jesse Gross. Based in part on "v4 GRE: Add TCP segmentation offload for GRE" by Pravin B Shelar. Cc: Jesse Gross <jesse@nicira.com> Cc: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: NSimon Horman <horms@verge.net.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Simon Horman 提交于
In order to mitigate ongoing incresase in the size of struct skbuff use 16 bit integer offsets rather than pointers for inner_*_headers. This appears to reduce the size of struct skbuff from 0xd0 to 0xc0 bytes on x86_64 with the following all unset. CONFIG_XFRM CONFIG_NF_CONNTRACK CONFIG_NF_CONNTRACK_MODULE NET_SKBUFF_NF_DEFRAG_NEEDED CONFIG_BRIDGE_NETFILTER CONFIG_NET_SCHED CONFIG_IPV6_NDISC_NODETYPE CONFIG_NET_DMA CONFIG_NETWORK_SECMARK Signed-off-by: NSimon Horman <horms@verge.net.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
The Broadcom BCM63xx PHY driver is for the SoC internal PHYs, flag these as internal PHY devices. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
libphy currently always reports a PHY as an external transceiver from the ethtool output. This is inaccurate, because some drivers should be able to tell that a PHY device is an internal transceiver of an Ethernet MAC. Add a new flag (PHY_IS_INTERNAL) which can be set by PHY drivers just like other flags, and a corresponding helper: phy_is_internal() which can be used by networking drivers to query if a given PHY device is internal. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Add a comment which explains the real meaning of XCVR_INTERNAL (PHY and Ethernet MAC in the same package/die) and XCVR_EXTERNAL (PHY and Ethernet MAC in a different package/die). Most if not all of the drivers setting their transceiver type already do it the way the comment describes it. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Reviewed-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jingoo Han 提交于
The driver core clears the driver data to NULL after device_release or on probe failure, since commit 0998d063 (device-core: Ensure drvdata = NULL when no driver is bound). Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: NJingoo Han <jg1.han@samsung.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jingoo Han 提交于
The driver core clears the driver data to NULL after device_release or on probe failure, since commit 0998d063 (device-core: Ensure drvdata = NULL when no driver is bound). Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: NJingoo Han <jg1.han@samsung.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jingoo Han 提交于
The driver core clears the driver data to NULL after device_release or on probe failure, since commit 0998d063 (device-core: Ensure drvdata = NULL when no driver is bound). Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: NJingoo Han <jg1.han@samsung.com> Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jingoo Han 提交于
The driver core clears the driver data to NULL after device_release or on probe failure, since commit 0998d063 (device-core: Ensure drvdata = NULL when no driver is bound). Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: NJingoo Han <jg1.han@samsung.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Acked-by: NRob Herring <rob.herring@calxeda.com> Acked-by: NRoland Stigge <stigge@antcom.de> Acked-by: NMugunthan V N <mugunthanvnm@ti.com> Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com> Tested-by: NRoland Stigge <stigge@antcom.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Fabio Estevam says: ==================== This series provides support for controlling the PHY regulator in suspend/resume. Fabio Estevam (5): fec: Place the phy regulator in the private structure fec: Invert the order of error path sequence fec: Disable the PHY regulator on error and removal fec: Remove irqs first fec: Handle the regulator in suspend/resume ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Fabio Estevam 提交于
In order to save power, let's disable the regulator in the suspend function and enable it in resume. Tested on a mx28evk board. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Fabio Estevam 提交于
During probe the clocks are enabled prior than the acquiring the interrupts. In the remove function we need to do the opposite: first remove the interrupts and then disable the clocks. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Fabio Estevam 提交于
In the case of error during probe, disable the PHY regulator. Do the same in fec_drv_remove(). Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Fabio Estevam 提交于
Currently when fec_enet_init fails it jumps to 'failed_init' error path, which will attemp to free the interrupts. This is wrong because at this point the interrupts have not even been acquired. Swap failed_init/failed_irq to fix the error path. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Fabio Estevam 提交于
Instead of using a local reg_phy structure, let's put it inside the private structure, so that we are able to have access to the regulator structure even when we are outside fec_probe(). This is in preparation for controlling the FEC PHY regulator in the suspend and resume functions. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Somnath Kotur 提交于
For padded packets, Lancer computes incorrect checksum. The workaround is to trim such packets. This workaround is mainly for IPv4 packets. Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com> Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Somnath Kotur 提交于
In Lancer, packets that are 32 bytes or less may cause a transmit stall. The work-around is to pad such packets to a 36 byte length. Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com> Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Somnath Kotur 提交于
Removing the be_cmd_get_fw_ver() query from be_get_drvinfo() and invoking the same from be_setup() and/or post firmware download. Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com> Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
This changes the PCI power management scheme of the bnx2x driver to be similar to those of most network drivers - the driver will now changes the power state into D3hot whenever the driver will be removed, instead of whenever an interface is unloaded. This change enables the driver to access its eeprom via ethtool callbacks even when interfaces are unloaded (such access requires the function to be in D0active). Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NAriel Elior <ariele@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Implement the PCI shutdown callback to support un-orderly shutdown, i.e., shutdowns in which the remove callback will not be called. Due to the lack of this functionality, when an un-orderly shutdown occurred, it was possible for wake-on-lan to remain disabled. This is now fixed as the callback introduces the correct place in which `system_state' can be queried and wake-on-lan be configured accordingly. Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NAriel Elior <ariele@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dmitry Kravkov 提交于
Commit 0eb43b4b "bnx2x, bnx2fc: Use per port max exchange resources" has changed the number of available FCoE exchanges, even in scenarios when some of the functions has no FCoE support; This needlessly degraded the available resources. Remedy this by calculating the maximal number of functions that may actually utilize said connection. Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com> CC: Bhanu Prakash Gollapudi <bprakash@broadcom.com> Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NAriel Elior <ariele@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ariel Elior 提交于
A PF should ack the firmware when receiving unknown messages through the VF's mailbox. This prevents the VF mailbox from being stuck in case of a VF sending a message unknown to the PF (e.g. VF with more advanced version). Signed-off-by: NAriel Elior <ariele@broadcom.com> Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dmitry Kravkov 提交于
This adds the print of the PCI gen3 link speed (8GHz), as well as correcting the same print for 57712 boards (the print erroneously showed a 2.5GHz speed). Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com> Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NAriel Elior <ariele@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ariel Elior 提交于
Hypervisor/Supervisor should set the VF's MAC prior to its load; Using a randomly generated MAC as a default is a bad practice. Signed-off-by: NAriel Elior <ariele@broadcom.com> Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 5月, 2013 6 次提交
-
-
由 Joe Perches 提交于
case TCP_FIN_WAIT1 can also be simplified by reversing tests and adding breaks; Add braces after case and move automatic definitions. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
case TCP_SYN_RECV: can have another indentation level removed by converting if (acceptable) { ...; } else { return 1; } to if (!acceptable) return 1; ...; Reflow code and comments to fit 80 columns. Another pure cleanup patch. Signed-off-by: NJoe Perches <joe@perches.com> Improved-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Remove one level of indentation 'introduced' in commit c3ae62af (tcp: should drop incoming frames without ACK flag set) if (true) { ... } @acceptable variable is a boolean. This patch is a pure cleanup. Signed-off-by: NEric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
Now when upper device is changed, event is not propagated via RT Netlink to userspace. Userspace might never now about the change. Fix this by adding upper-device-change notifier event. Signed-off-by: NJiri Pirko <jiri@resnulli.us> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jingoo Han 提交于
Use the wrapper functions for getting and setting the driver data using platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev, so we can directly pass a struct platform_device. Also, unnecessary dev_set_drvdata() is removed, because the driver core clears the driver data to NULL after device_release or on probe failure. Signed-off-by: NJingoo Han <jg1.han@samsung.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Lorenzo Colitti 提交于
This adds the ability to send ICMPv6 echo requests without a raw socket. The equivalent ability for ICMPv4 was added in 2011. Instead of having separate code paths for IPv4 and IPv6, make most of the code in net/ipv4/ping.c dual-stack and only add a few IPv6-specific bits (like the protocol definition) to a new net/ipv6/ping.c. Hopefully this will reduce divergence and/or duplication of bugs in the future. Caveats: - Setting options via ancillary data (e.g., using IPV6_PKTINFO to specify the outgoing interface) is not yet supported. - There are no separate security settings for IPv4 and IPv6; everything is controlled by /proc/net/ipv4/ping_group_range. - The proc interface does not yet display IPv6 ping sockets properly. Tested with a patched copy of ping6 and using raw socket calls. Compiles and works with all of CONFIG_IPV6={n,m,y}. Signed-off-by: NLorenzo Colitti <lorenzo@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 5月, 2013 3 次提交
-
-
由 David S. Miller 提交于
Shahed Shaikh says: ==================== This patch series includes following changes: * Support for spoof check configuration per VF using iproute2 tool. * Set HW mask for 8300 adapter in INT-x mode to stop generating interrupts. * Updated IRQ name for 8200 and 8300 Series adapter as per format used by other multiqueue drivers. * Remove qlcnic_config_npars module parameter. * Initialize trans_work and idc_aen_work at VF probe. * Convert netsted if-else into switch-case statement. * Change in diagnostics routine. * Modify reset recovery path in diag mode by providing diagnostics routines enough time to unwind before proceeding with reset recovery. * Implement GET_LED_STATUS command for 82xx adapter and refactor qlcnic_store_beacon() to split 8200 and 8300 specific calls. * Some cleanup and log enhancements ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shahed Shaikh 提交于
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Manish Chopra 提交于
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com> Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-