Propagate errors from wl1271_raw_write32 and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Propagate errors from wl1271_raw_read32. Since the read functions had no
way of returning errors in-band, change their prototypes.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Propagate errors from wl1271_write and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Propagate errors from wl1271_read and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

18xx chips do not require extra space in the TKIP header. Introduce a
new HW quirk to allow us to make this feature arch-specific. 12xx chip
will now have this quirk.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In some multi role scenarios the driver might send multi
roc requests without sending a croc first, the fw queues
those requests and starts service the next roc request as
soon as the driver sends a croc for the previous one. So,
if the fw rocs on channel X and driver asks to roc also
on channel Y, the fw will not start service Y (and will
not send roc complete event for this request) until the
driver releases the fw with croc X.
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In ieee80211.h the uapsd bit mask is defined such that
VO=BIT(0), VI=BIT(1), BK=BIT(2), BE=BIT(3).
The firmware uses the indexing as defined in the ieee80211
spec, meaning that VO=3, VI=2, BK=1, BE=0.

In AP mode when adding peer wlcore needs to convert
the indexing accordingly.
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We were setting all the rates bits when starting the AP role.  Instead
of doing this, we should set only the rates we really support
(eg. MIMO rates or wide-channel rates).  This commit changes that so
that we always use the default rates (basic rates + MCS0-7) and add
the values returned by the ap_get_mimo_wide_rate_mask operation.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

PLT mode needs to be initialized differently for each chip.  This
patch adds an operation to init PLT and moves the existing PLT
initialization into the wl12xx driver.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

Parse the peer ht_cap element containing MCS8-MCS15 rates and pass it
to the FW. Rates unsupported by the HW will be sanitized by mac80211
before reaching us.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Translate the NL80211 channel type to a FW-specific channel type and send
it to the FW as part of the role-start command. For wl12xx this has no
effect - this element is treated as padding.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We currently do this:

int wl1271_cmd_build_arp_rsp(struct wl1271 *wl, struct wl12xx_vif *wlvif)
...
      struct wl12xx_arp_rsp_template *tmpl;
      struct ieee80211_hdr_3addr *hdr;
...
      tmpl = (struct wl12xx_arp_rsp_template *)skb_put(skb, sizeof(*tmpl));
      memset(tmpl, 0, sizeof(tmpl));
...
      hdr = (struct ieee80211_hdr_3addr *)skb_push(skb, sizeof(*hdr));
      memset(hdr, 0, sizeof(hdr));
...

I believe we want to set the entire structures to 0 with those
memset() calls, not just zero the initial part of them (size of the
pointer bytes).
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

GFP_DMA isn't supposed to be used by itself.  This allocation is allowed
to sleep so it should be ORing it with GFP_KERNEL.
Also we should check for allocations errors.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Change the cmd_trigger op to include the write of the command buffer.

Also, instead of letting the lower driver access the cmd_box_addr element
directly, we now pass the address in the trigger_cmd operation, so it
doesn't have to be exported.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Move all the wl12xx-specific hw initialization procedures into a new
hw_init op.  Move some commands and ACX functions to wl12xx.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Different chips may use different bits in the interrupt trigger
register.  Add operations to handle these differences.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add register tables support in wlcore, add some new IO functions to
read and write to chip-specific register and data addresses.  Move
some common register values from wl12xx to wlcore and add the
registers table to wl12xx.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In order to add chip-specific operations and prepare for future
elements that need to be set by the lower driver, move the wl1271
structure to the wlcore.h file and add an empty placeholder for the
operations structure.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Rename the wl12xx driver directory to wlcore as an initial step
towards the split of the driver into wlcore and wl12xx.  We just
rename the directory first to keep git blame happy.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Move wl12xx and wl1251 modules into a new drivers/net/wireless/ti
directory.  Add a TI WLAN Kconfig option and Makefile to support this
change.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Cc: John W. Linville <linville@tuxdriver.com>

On the PandaBoard (omap_hsmmc + wl12xx_sdio) with DMA_API_DEBUG:

 WARNING: at lib/dma-debug.c:930 check_for_stack.part.8+0x7c/0xe0()
 omap_hsmmc omap_hsmmc.4: DMA-API: device driver maps memory fromstack
Signed-off-by: NMircea Gherzan <mgherzan@gmail.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Track freed FW blocks during Tx. If no blocks were freed during a
predefined timeout, initiate a HW recovery. This helps in situations
when the FW watchdog fails.

Don't trigger recovery during activities that can temporarily stop
Tx. This includes:
- scanning
- buffering packets for sleeping stations (AP role)
- ROC on any role
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The sesssion_counter has to be incremented each time
the dev is started (similar to sta role).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Before, the link was first freed (invalidating it in the map), and later
on vif removal, all valid wlvif-related links were reset. Since these
links were already invalid, we failed to reset them.
The bug was made worse by op_stop, which set the tx_queue_count to 0
arbitrarily. This resulted in a negative tx_queue_count in some scenarios.

Fix this by resetting the Tx-queues of a link when freeing it. Add a
WARN_ON and reset all link Tx-queues in op_stop, to avoid a negative
tx_queue_count.

[changed WARN_ON to WARN_ON_ONCE -- Luca]
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

These bits are used in op_tx to determine if a packet should be dropped.
As such we should use the spin lock to sync the state.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

When configuring the arp response template,
and encryption is enabled, we should add some
space and set the protected flag bit in the fc.

In order to track the encryption type, set
wlvif->encryption_type when setting an encryption key,
and reconfigure the arp response. Clear this field on
wl1271_join, as keys have to be re-configured
anyway after a join command.

Similarly, track whether QoS is configured.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

FW now supports dynamic PS so we don't need to use mac80211 support.
FW will go to PSM after a specified timeout with no Rx/Tx traffic.
- Changed FW API to include new PS mode (AUTO_MODE) and including timeout parameter
- The default PS mode would be dynamic PS
- Default timeout is 100ms (same as it used to be in mac80211)
- Avoid using mac80211 APIs to disable/enable dynamic PS as we're not
using mac80211 PS control anymore.
- COEX is handled by the FW while in dynamic PS so removed
handling of SOFT_GEMINI
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Update enums/structs to the new fw api.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Use device role for scans when the sta is not
associated.

sched_scan is used only when the sta is
not associated, and thus should use
the dev role (instead of sta role).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The set_template commands now takes the role_id as
parameter.

Usually, we'll use the vif's main role_id.
However, sometimes we'll want to use
wlvif->dev_role_id instead of wlvif->role_id,
so pass the wanted role_id as param.

Update WL127X_FW_NAME/WL128X_FW_NAME.

(This commit starts a series of fw update patches,
and changes the start() callback to return an error
in order to prevent the use of the driver during the
transition. This change will be reverted in the
last patch of series)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

During sta disconnection, a deauth packet is being queued to
the dev role queue. However, the dev role is being stopped
before the packet was sent.

Flush the tx queue before stopping the dev role.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Check for out of bound FEM index to prevent reading beyond ini
memory end.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Cc: stable@kernel.org
Reviewed-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Device role is always started along with ROC.
Couple them together by introducing new wl12xx_start_dev
and wl12xx_stop_dev functions.

By using these functions, we solve a bug that occured during
channel switch - we started the dev role on one channel, and
ROCed on a different one.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Separate the debugging macros and other definitions to a new debug.h
file.  This is be needed because the sdio and spi modules don't need
to depend on the wl12xx module anymore, but still need to include
wl12xx.h.  Currently they do depend on it, because of the debugging
global that wl12xx exports.  A future patch will remove this
dependency.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

wl->vif is appropriate only when a single vif is being used.
Instead, pass wlvif as parameter or iterate through all
the vifs (e.g. when a global configuration was changed)

Leave wl->vif only to determine whether a vif was already
added (this check will be removed as well after both the
driver and fw will support multiple vifs)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

add channel into the per-interface data.

mac80211 configures some values (e.g. band, channel)
globally, while we configure them per-interface.

In order to make it easier to keep track of the
configured value for each value while keeping sync
with mac80211, save these values both globally
and per-vif.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

add band field into the per-interface data.

mac80211 configures some values (e.g. band, channel)
globally, while we configure them per-interface.

In order to make it easier to keep track of the
configured value for each value while keeping sync
with mac80211, save these values both globally
and per-vif.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

move bitrate_masks into the per-interface data, rather than
being global.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add wlvif->links_map bitmap to represent all the links
allocated for this vif.

AP vif also has a sta_hlid_map bitmap, which represents
the links stations connected to it (sta_hlid_bitmap is
a subset of wlvif->links_map, which itself is a subset
of the global wl->links_map)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

move beacon_int into the per-interface data, rather than
being global.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>