Add revision detection for ES1.1 and ES1.2. Set default
revision as ES1.2.

Add CHIP_GE_OMAP3630ES1_1 to detect revisions 1.1 and later.
This is needed for at least one feature that is broken in
3630ES1.0 but exists on older (3430 ES3.1) and newer revisions.

Additionally, update some of the CHIP_GE_* macros to use other
macros for ease of maintenance.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Manjunatha GK <manjugk@ti.com>
[tony@atomide.com: update to remove fallthrough handling]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Do not forget to check the 'platform_device_add_data()' error code
in 'omap_device_build_ss()'.
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: NNishanth Menon <nm@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Most OMAP3-based boards use exactly the same code for .map_io method in
the machine_desc structure.
This patch introduces omap3_map_io and updates board-* files to use it
as .map_io method.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The only difference between them is the physical address of the
uart4 port, which is only present in 36xx chips.

We don't really need to care about keeping these 2 functions, since
the decision to use uart4 is more cleanly done later when we do have
access to omap_revision variable.
Signed-off-by: NSergio Aguirre <saaguirre@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: added comment for the uart4_phys]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Now we use a memory address to store the debug port info, So we need
to read/write this address when we choose DEBUG_LL. When MMU isn't
enable(I.E. the begining part of init stage of the linux kernel boot),
we need to access physical address instead of virtual address,
otherwise the kernel will crash.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (291 commits)
  ARM: AMBA: Add pclk support to AMBA bus infrastructure
  ARM: 6278/2: fix regression in RealView after the introduction of pclk
  ARM: 6277/1: mach-shmobile: Allow users to select HZ, default to 128
  ARM: 6276/1: mach-shmobile: remove duplicate NR_IRQS_LEGACY
  ARM: 6246/1: mmci: support larger MMCIDATALENGTH register
  ARM: 6245/1: mmci: enable hardware flow control on Ux500 variants
  ARM: 6244/1: mmci: add variant data and default MCICLOCK support
  ARM: 6243/1: mmci: pass power_mode to the translate_vdd callback
  ARM: 6274/1: add global control registers definition header file for nuc900
  mx2_camera: fix type of dma buffer virtual address pointer
  mx2_camera: Add soc_camera support for i.MX25/i.MX27
  arm/imx/gpio: add spinlock protection
  ARM: Add support for the LPC32XX arch
  ARM: LPC32XX: Arch config menu supoport and makefiles
  ARM: LPC32XX: Phytec 3250 platform support
  ARM: LPC32XX: Misc support functions
  ARM: LPC32XX: Serial support code
  ARM: LPC32XX: System suspend support
  ARM: LPC32XX: GPIO, timer, and IRQ drivers
  ARM: LPC32XX: Clock driver
  ...

avoid potential stack overflow by correctly checking count parameter
Reported-by: NIlja <ilja@netric.org>
Signed-off-by: NHelge Deller <deller@gmx.de>
Acked-by: NKyle McMartin <kyle@mcmartin.ca>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a missing break at end of switch statement. At the moment it is a
fall through to WARN_ON(1) and return -EEXIST.
Signed-off-by: NThomas Weber <weber@corscience.de>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

patch adds NAND support to LDP board.
Signed-off-by: NVimal Singh <vimalsingh@ti.com>
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

add support for NAND, OneNAND, NOR on omap 3630-sdp board.
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

patch adds NAND support to zoom3 board.
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NVimal Singh <vimalsingh@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds NAND support to ZOOM2 board.
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NVimal Singh <vimalsingh@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

rename board-sdp-flash.c(board-flash.c) and board-sdp.h(board-flash.h) to
used by other board e.g. zoom
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Board file modified for not to provide gpmc phys_base address to nand driver.
The gpmc_nand_init funciton is now used to detect the nand and required to
adopt _prob function as in nand/omap2.c
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch removes direct reference of gpmc address from generic nand platform code.
Nand platform code now uses wrapper functions which are implemented in gpmc module.
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

few functions added in gpmc module and to be used by other drivers like NAND.
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP3530 CBB package can have GPIO126 muxed on 2 pins: mmc1_dat4 and
cam_strobe. This causes a problem with current multipath GPIO mux
handling, which muxes both pins as GPIO126 and makes the GPIO unusable.

Fix this by not muxing any pins if multipath GPIO is detected and
just print a warning instead. It's up to board files to set correct
mux using omap_mux_init_signal and pin name.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The devkit8000 boards often come with empty EEPROM thus without
valid ethernet MAC address. The DIE id to MAC formula is copied from
u-boot.
Signed-off-by: NKan-Ru Chen <kanru@0xlab.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NKan-Ru Chen <kanru@0xlab.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Allow DIE id to be get and used by others.
Signed-off-by: NKan-Ru Chen <kanru@0xlab.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

AM3505/3517 doesn't have IO wakeup capability, so we do not need to set
the bit OMAP3430_EN_IO and the bit OMAP3430_EN_IO_CHAIN in the register
PM_WKEN_WKUP when the system enters suspend state.

Tested on AM3517EVM and OMAP3530EVM.
Signed-off-by: NStanley.Miao <stanley.miao@windriver.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Omap DMA controller can prefetch data in advance in case of
destination synchronized data transfer. This may increase
performance when target HW block doesn't have fifo.
Data is waiting for transfer request in DMA fifo instead of read from memory.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap24xx_check_revision, omap3_check_features,
omap3_check_revision, omap4_check_revision, omap3_cpuinfo
are not used elsewhere, it should be static

Also fixes the following sparse warnings:
arch/arm/mach-omap2/id.c:105:13: warning: symbol 'omap24xx_check_revision'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:167:13: warning: symbol 'omap3_check_features'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:189:13: warning: symbol 'omap3_check_revision'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:270:13: warning: symbol 'omap4_check_revision'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:300:13: warning: symbol 'omap3_cpuinfo'
was not declared. Should it be static?
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The original patch got truncated when applied from patchwork.kernel.org
as discussed at:

http://www.mail-archive.com/linux-omap@vger.kernel.org/msg28953.html

This patch supplies the missing chunks.
Signed-off-by: NSteve Sakoman <sakoman@gmail.com>
[tony@atomide.com: added more info to the patch description]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix GPIO numbers and smc91x for 2430sdp. The earlier code
had cut and paste errors from 3430sdp code. Also, 2430
has five GPIO banks for a total of 160 GPIO lines.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This change adds in the necessary clocks and mux pins for UART
control on omap7xx devices.  I also made a change in the serial
code to only try and initialize two UARTs in omap_serial_init, as
these devices don't have three.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Recent DEBUG_LL and uncompress.h changes removed the check_port()
as pointed out by Cory Maccarrone <darkstar6262@gmail.com>.

This causes some boards to not boot, so add back the MDR1 register
check. The MDR1 register tells the mode of omap uart. Based on
an earlier patch by Cory Maccarrone <darkstar6262@gmail.com>.
Tested-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds cpu hotplug support for OMAP4430. Only CPU inactive
state is supported as a low power state in the basic hot-plug support
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds a secure API to read AuxCoreBoot0 register to
check the cpu boot status. It also moves the other smc APIs
to common omap44xx-smc.S. This APIs should not be marked as
__INIT because we need these to be present for CPU hotplug
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for basic suspend doing a CPUx wfi
for OMAP4. All powerdomains are for now are kept programmed
in ON state.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Errata i202 (OMAP3430 - 1.12, OMAP3630 - 1.6):
UART module MDR1 register access can cause a dummy underrun
condition which could result in a freeze in the case of IrDA
communication or if used as UART, corrupted data.

Workaround is as follows for everytime MDR1 register is changed:
* setup all required UART registers
* setup MDR1.MODE_SELECT bit field
* Wait 5 L4 clk cycles + 5 UART functional clock cycles
* Clear the Tx and RX fifo using FCR register

Note: The following step is not done as I am assuming it is not
needed due to reconfiguration being done and there is no halted
operation perse.
* Read if required, the RESUME register to resume halted operation

Based on an earlier patch at:
http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=42d4a342c009bd9727c100abc8a4bc3063c22f0cSigned-off-by: NDeepak K <deepak.k@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

introduce silicon specific quirks as a errata handling mechanism

as a start UART_ERRATA_FIFO_FULL_ABORT is used to handle the override
for fifo full condition for rx and tx.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove the following sparse warnings by declaring attr as static:
arch/arm/mach-omap2/serial.c:627:1: warning: symbol 'dev_attr_sleep_timeout'
was not declared. Should it be static?
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initialization of pointer should be done with NULL. Removes sparse
warnings:
arch/arm/mach-omap2/serial.c:566:17: warning: Using plain integer as NULL pointer
arch/arm/mach-omap2/serial.c:567:17: warning: Using plain integer as NULL pointer
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adds context save/restore for mcr register as state of mcr register
is lost after core off.
Signed-off-by: NGovindraj R <govindraj.raja@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add initial support for the OMAP4 based Panda Board.
Signed-off-by: NDavid Anders <x0132446@ti.com>
[tony@atomide.com: selected board by default in Kconfig]
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for GPIO LEDs present on OMAP4
SDP and Blaze boards. This basically adds platform data
required by leds-gpio driver
Signed-off-by: NHemanth V <hemanthv@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>