Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 01 9月, 2019 4 次提交
    • D
      Merge branch 'Dynamic-toggling-of-vlan_filtering-for-SJA1105-DSA' · b0274eb0
      由 David S. Miller 提交于 
      Vladimir Oltean says:

====================
Dynamic toggling of vlan_filtering for SJA1105 DSA

This patchset addresses a limitation in dsa_8021q where this sequence of
commands was causing the switch to stop forwarding traffic:

  ip link add name br0 type bridge vlan_filtering 0
  ip link set dev swp2 master br0
  echo 1 > /sys/class/net/br0/bridge/vlan_filtering
  echo 0 > /sys/class/net/br0/bridge/vlan_filtering

The issue has to do with the VLAN table manipulations that dsa_8021q
does without notifying the bridge layer. The solution is to always
restore the VLANs that the bridge knows about, when disabling tagging.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b0274eb0
    • V
      net: dsa: tag_8021q: Restore bridge VLANs when enabling vlan_filtering · 5f33183b
      由 Vladimir Oltean 提交于 
      The bridge core assumes that enabling/disabling vlan_filtering will
translate into the simple toggling of a flag for switchdev drivers.

That is clearly not the case for sja1105, which alters the VLAN table
and the pvids in order to obtain port separation in standalone mode.

There are 2 parts to the issue.

First, tag_8021q changes the pvid to a unique per-port rx_vid for frame
identification. But we need to disable tag_8021q when vlan_filtering
kicks in, and at that point, the VLAN configured as pvid will have to be
removed from the filtering table of the ports. With an invalid pvid, the
ports will drop all traffic.  Since the bridge will not call any vlan
operation through switchdev after enabling vlan_filtering, we need to
ensure we're in a functional state ourselves. Hence read the pvid that
the bridge is aware of, and program that into our ports.

Secondly, tag_8021q uses the 1024-3071 range privately in
vlan_filtering=0 mode. Had the user installed one of these VLANs during
a previous vlan_filtering=1 session, then upon the next tag_8021q
cleanup for vlan_filtering to kick in again, VLANs in that range will
get deleted unconditionally, hence breaking user expectation. So when
deleting the VLANs, check if the bridge had knowledge about them, and if
it did, re-apply the settings. Wrap this logic inside a
dsa_8021q_vid_apply helper function to reduce code duplication.
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5f33183b
    • V
      net: bridge: Populate the pvid flag in br_vlan_get_info · f40d9b20
      由 Vladimir Oltean 提交于 
      Currently this simplified code snippet fails:

	br_vlan_get_pvid(netdev, &pvid);
	br_vlan_get_info(netdev, pvid, &vinfo);
	ASSERT(!(vinfo.flags & BRIDGE_VLAN_INFO_PVID));

It is intuitive that the pvid of a netdevice should have the
BRIDGE_VLAN_INFO_PVID flag set.

However I can't seem to pinpoint a commit where this behavior was
introduced. It seems like it's been like that since forever.

At a first glance it would make more sense to just handle the
BRIDGE_VLAN_INFO_PVID flag in __vlan_add_flags. However, as Nikolay
explains:

  There are a few reasons why we don't do it, most importantly because
  we need to have only one visible pvid at any single time, even if it's
  stale - it must be just one. Right now that rule will not be violated
  by this change, but people will try using this flag and could see two
  pvids simultaneously. You can see that the pvid code is even using
  memory barriers to propagate the new value faster and everywhere the
  pvid is read only once.  That is the reason the flag is set
  dynamically when dumping entries, too.  A second (weaker) argument
  against would be given the above we don't want another way to do the
  same thing, specifically if it can provide us with two pvids (e.g. if
  walking the vlan list) or if it can provide us with a pvid different
  from the one set in the vg. [Obviously, I'm talking about RCU
  pvid/vlan use cases similar to the dumps.  The locked cases are fine.
  I would like to avoid explaining why this shouldn't be relied upon
  without locking]

So instead of introducing the above change and making sure of the pvid
uniqueness under RCU, simply dynamically populate the pvid flag in
br_vlan_get_info().
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f40d9b20
    • D
      Merge tag 'batadv-next-for-davem-20190830' of git://git.open-mesh.org/linux-merge · 5c63592f
      由 David S. Miller 提交于 
      Simon Wunderlich says:

====================
This maintenance patchset includes the following patches:

 - Add Sven to the MAINTAINERS file, by Simon Wunderlich
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5c63592f
  3. 31 8月, 2019 36 次提交