The DECAP_ECN0 trap will be used to trap packets where the overlay
packet is marked with Non-ECT, but the underlay packet is marked with
either ECT(0), ECT(1) or CE. When trapped, such packets will be counted
as errors by the VxLAN driver and thus provide better visibility.

The NVE_ENCAP_ARP trap will be used to trap ARP packets undergoing NVE
encapsulation. This is needed in order to support E-VPN ARP suppression,
where the Linux bridge does not flood ARP packets through tunnel ports
in case it can answer the ARP request itself.

Note that all the packets trapped via these traps are marked with
'offload_fwd_mark', so as to not be re-flooded by the Linux bridge
through the ASIC ports.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the seed of the LAG hash function is always set to 0, which
means it is identical across all switches. Instead, use a random number.

This is especially important now that VxLAN is supported, as the LAG
hash function is used to calculate the UDP source port of the
encapsulated packet.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 602b74ed ("mlxsw: spectrum_switchdev: Do not leak RIFs
when removing bridge") I handled the case where RIFs created for VLAN
devices were not properly cleaned up when their real device (a bridge)
was removed.

However, I forgot to handle the case of the VLAN device itself being
removed. Do so now when the VLAN device is being unlinked from its real
device.

Fixes: 99f44bb3 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Reported-by: NArtem Shvorin <art@qrator.net>
Tested-by: NArtem Shvorin <art@qrator.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now, mlxsw tolerated firmware versions that weren't exactly
matching the required version, if the branch number matched. That
allowed the users to test various firmware versions as long as they were
on the right branch.

On the other hand, it made it impossible for mlxsw to put a hard lower
bound on a version that fixes all problems known to date. If a user had
a somewhat older FW version installed, mlxsw would start up just fine,
possibly performing non-optimally as it would use features that trigger
problematic behavior.

Therefore tweak the check to accept any FW version that is:

- on the same branch as the preferred version, and
- the same as or newer than the preferred version.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MC-aware mode was introduced to mlxsw in commit 7b819530 ("mlxsw: spectrum:
Configure MC-aware mode on mlxsw ports") and fixed up later in commit
3a3539cd ("mlxsw: spectrum_buffers: Set up a dedicated pool for BUM
traffic"). As the final piece of puzzle, a firmware issue whereby a wrong
priority was assigned to BUM traffic was corrected in FW version 13.1703.4.
Therefore require this FW version in the driver.

Fixes: 7b819530 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With introduction of MC-aware mode to mlxsw, it became necessary to
configure TCs above 7 as well. There is now code in mlxsw to disable ETS
for these higher classes, but disablement of max shaper was neglected.

By default, max shaper is currently disabled to begin with, so the
problem is just cosmetic. However, for symmetry, do like we do for ETS
configuration, and call mlxsw_sp_port_ets_maxrate_set() for both TC i
and i + 8.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 90b73b77, list_head is no longer needed.
Now we just need to convert the list iteration to array
iteration for drivers.

Fixes: 90b73b77 ("net: sched: change action API to use array of pointers to actions")
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before MC-aware mode was enabled in commit 7b819530 ("mlxsw:
spectrum: Configure MC-aware mode on mlxsw ports"), only 8 traffic
classes were used. Under MC-aware regime, however, besides using TCs
0-7 for UC traffic, it additionally uses TCs 8-15 for BUM traffic. It
is therefore desirable to show counters for these TCs as well.

Update ethtool stats pool length, mlxsw_sp_port_get_strings() and
mlxsw_sp_port_get_stats() to include artifacts for all 16 TCs. For
consistency and simplicity, expose tc_no_buffer_discard_uc_tc for BUM
TCs as well, even though it ought to stay at 0 all the time.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function mlxsw_sp_port_get_sset_count() is supposed to return the
total number of ethtool strings that mlxsw supports. Specifically for
names of statistic counters (the only string type that mlxsw supports
as of now), that number is stored in MLXSW_SP_PORT_ETHTOOL_STATS_LEN.
However, when adding RFC-2891 counters, that define wasn't updated to
include the new counters. As a result, ethtool snips out the counters
towards the end of the list, which contains per-TC counters, and only
the first three traffic classes end up being reported.

Fix by adding MLXSW_SP_PORT_HW_RFC_2819_STATS_LEN as appropriate.

Fixes: 1222d15a ("mlxsw: spectrum: Expose counters for various packet sizes")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent FW fixes a bug and allows to load newly flashed FW image after
reset. So make sure the reset happens after flash. Indicate the need
down to PCI layer by -EAGAIN.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This new firmware contains:
        - Support for new types of cables
        - Support for flashing future firmware without reboot
        - Support for Router ARP BC and UC traps
Signed-off-by: NNir Dotan <nird@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to give unicast traffic precedence over BUM traffic, configure
multicast-aware mode on all ports.

Under multicast-aware regime, when assigning traffic class to a packet,
the switch doesn't merely take the value prescribed by the QTCT
register. For BUM traffic, it instead assigns that value plus 8.

ETS elements for TCs 8..15 thus need to be configured as well. Extend
mlxsw_sp_port_ets_init() so that it maps each of them to the same
subgroup as their corresponding TC from the range 0..7, such that TCs X
and X+8 map to the same subgroup.

The existing code configures TCs with strict priority. So far this was
immaterial, because each TC had its own subgroup. Now that two TCs share
a subgroup it becomes important. TCs are prioritized in order of 7, 6,
..., 0, 15, 14, ..., 8: the higher TCs used for BUM traffic end up being
deprioritized. Since that's what's needed, keep that configuration as it
is, and configure the new TCs likewise.

Finally in mlxsw_sp_port_create(), invoke configuration of QTCTM to
enable MC-aware mode on each port.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since cld_flower provides information about the filter template for
specific chain, use this information in order to prepare a region.
Use the template to find out what elements are going to be used
and pass that down to mlxsw_sp_acl_tcam_group_add(). Later on, when the
first filter is inserted, the mlxsw_sp_acl_tcam_group_use_patterns()
function would use this element usage information instead of looking
up a pattern.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend existing driver for Spectrum ASIC to support Spectrum-2 ASIC.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Expose counters ASIC has in the group of RFC 2819 counters that count
number of packets within specific size range.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Virtual Router Redundancy Protocol packets are used to communicate the
state of the Master router associated with the virtual router ID (VRID).

These are link-local multicast packets sent with IP protocol 112 that
are trapped in the router block in the ASIC.

Add a trap for these packets and mark the trapped packets to prevent
them from potentially being re-flooded by the bridge driver.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An IP packet received on a netdev with a macvlan upper whose MAC matches
the packet's destination MAC will be re-injected to the Rx path as if it
was received by the macvlan, and perform an L3 lookup.

Reflect this functionality to the ASIC by programming FDB entries that
will direct MACs of macvlan uppers to the router.

In a similar fashion to router interfaces (RIFs) that are programmed
upon the addition of the first IP address on an interface and destroyed
upon the removal of the last IP address, the FDB entries for the macvlan
are added and destroyed based on the addition of the first and removal
of the last IP address on the macvlan.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to allow more unicast MAC addresses (e.g., VRRP virtual MAC) to
be directed to the router we need to enable macvlan uppers on top of
mlxsw netdevs.

Allow macvlan upper devices on top of mlxsw netdevs and sanitize
configurations that can't work. For example, a macvlan can't be enslaved
to a bridge as without ACLs the device doesn't take the destination MAC
into account when classifying a packet to a bridge instance (i.e., a
FID).
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prepare for Spectrum-2 FW version checking and
make mlxsw_sp_fw_rev_validate() per-ASIC as well as required FW revision
and FW filename.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the flex keys for Spectrum-2 differ not only in blocks definitions
but also in encoding layout, prepare for the implementation and pass
Spectrum/Spectrum-2 specific ops down to mlxsw_afk_create.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To allow easy and clean Spectrum-2 implementation for things that differ
from Spectrum, split the existing ACL TCAM code 3 ways:
1) common code that calls Spectrum/Spectrum-2 specific ops
2) Spectrum ops implementations
3) common C-TCAM code that is going to be shared between Spectrum and
   Spectrum-2 implementations
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since Spectrum-2 has different handling of TCAM, push Spectrum MR TCAM
bits to a separate file accessible by ops which allows to implement
Spectrum-2 specific ops.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Spectrum-2 there is a different implementation of KVD linear
management. Unlike in Spectrum where there is a single index space,
in Spectrum-2 the indexes are per-resource. Also there is need to
explicitly tell HW that an entry is no longer used.
So push out the existing implementation into spectrum1_kvdl.c and
prepare ops infrastructure to allow new implementation in a follow-up.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Spectrum-2 need a slightly different handling of flexible actions. So
put an ops pointer in mlxsw_sp struct and rename it.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call the reoffload tcf_proto_op on all tcf_proto nodes in all chains of a
block when a callback tries to register to a block that already has
offloaded rules. If all existing rules cannot be offloaded then the
registration is rejected. This replaces the previous policy of rejecting
such callback registration outright.

On unregistration of a callback, the rules are flushed for that given cb.
The implementation of block sharing in the NFP driver, for example,
duplicates shared rules to all devs bound to a block. This meant that
rules could still exist in hw even after a device is unbound from a block
(assuming the block still remains active).
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass the extact struct from a tc qdisc add to the block bind function and,
in turn, to the setup_tc ndo of binding device via the tc_block_offload
struct. Pass this back to any block callback registrations to allow
netlink logging of fails in the bind process.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return messages in extack for port split/unsplit errors. e.g.,
    $ devlink port split swp1s1 count 4
    Error: mlxsw_spectrum: Port cannot be split further.
    devlink answers: Invalid argument

    $ devlink port unsplit swp4
    Error: mlxsw_spectrum: Port was not split.
    devlink answers: Invalid argument
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VLAN 1 is internally used for untagged traffic. Prevent creation of
explicit netdevice for that VLAN, because that currently isn't supported
and leads to the NULL pointer dereference cited below.

Fix by preventing creation of VLAN devices with VID of 1 over mlxsw
devices or LAG devices that involve mlxsw devices.

[  327.175816] ================================================================================
[  327.184544] UBSAN: Undefined behaviour in drivers/net/ethernet/mellanox/mlxsw/spectrum_fid.c:200:12
[  327.193667] member access within null pointer of type 'const struct mlxsw_sp_fid'
[  327.201226] CPU: 0 PID: 8983 Comm: ip Not tainted 4.17.0-rc4-petrm_net_ip6gre_headroom-custom-140 #11
[  327.210496] Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2F"/"SA000874", BIOS 4.6.5 03/08/2016
[  327.219872] Call Trace:
[  327.222384]  dump_stack+0xc3/0x12b
[  327.234007]  ubsan_epilogue+0x9/0x49
[  327.237638]  ubsan_type_mismatch_common+0x1f9/0x2d0
[  327.255769]  __ubsan_handle_type_mismatch+0x90/0xa7
[  327.264716]  mlxsw_sp_fid_type+0x35/0x50 [mlxsw_spectrum]
[  327.270255]  mlxsw_sp_port_vlan_router_leave+0x46/0xc0 [mlxsw_spectrum]
[  327.277019]  mlxsw_sp_inetaddr_port_vlan_event+0xe1/0x340 [mlxsw_spectrum]
[  327.315031]  mlxsw_sp_netdevice_vrf_event+0xa8/0x100 [mlxsw_spectrum]
[  327.321626]  mlxsw_sp_netdevice_event+0x276/0x430 [mlxsw_spectrum]
[  327.367863]  notifier_call_chain+0x4c/0x150
[  327.372128]  __netdev_upper_dev_link+0x1b3/0x260
[  327.399450]  vrf_add_slave+0xce/0x170 [vrf]
[  327.403703]  do_setlink+0x658/0x1d70
[  327.508998]  rtnl_newlink+0x908/0xf20
[  327.559128]  rtnetlink_rcv_msg+0x50c/0x720
[  327.571720]  netlink_rcv_skb+0x16a/0x1f0
[  327.583450]  netlink_unicast+0x2ca/0x3e0
[  327.599305]  netlink_sendmsg+0x3e2/0x7f0
[  327.616655]  sock_sendmsg+0x76/0xc0
[  327.620207]  ___sys_sendmsg+0x494/0x5d0
[  327.666117]  __sys_sendmsg+0xc2/0x130
[  327.690953]  do_syscall_64+0x66/0x370
[  327.694677]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  327.699782] RIP: 0033:0x7f4c2f3f8037
[  327.703393] RSP: 002b:00007ffe8c389708 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[  327.711035] RAX: ffffffffffffffda RBX: 000000005b03f53e RCX: 00007f4c2f3f8037
[  327.718229] RDX: 0000000000000000 RSI: 00007ffe8c389760 RDI: 0000000000000003
[  327.725431] RBP: 00007ffe8c389760 R08: 0000000000000000 R09: 00007f4c2f443630
[  327.732632] R10: 00000000000005eb R11: 0000000000000246 R12: 0000000000000000
[  327.739833] R13: 00000000006774e0 R14: 00007ffe8c3897e8 R15: 0000000000000000
[  327.747096] ================================================================================

Fixes: 9589a7b5 ("mlxsw: spectrum: Handle VLAN devices linking / unlinking")
Suggested-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since devlink knows the info needed to generate the physical port name
in a generic way for all devlink users, use the helper to do the job.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change existing setter for split port information into more generic
attrs setter. Alongside with that, allow to set port number and subport
number for split ports.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since switchdev events can trigger SPAN respin, it is necessary that the
data structures are available. Register SPAN first, with a commentary on
what the dependencies are.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of duplicating the decision regarding port forwarding state made
by mlxsw_sp_port_vid_stp_set(), extract the decision-making into a new
function and reuse.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This resolves race during initialization where the resources with
ops are registered before driver and the structures used by occ_get
op is initialized. So keep occ_get callbacks registered only when
all structs are initialized.

The example flows, as it is in mlxsw:
1) driver load/asic probe:
   mlxsw_core
      -> mlxsw_sp_resources_register
        -> mlxsw_sp_kvdl_resources_register
          -> devlink_resource_register IDX
   mlxsw_spectrum
      -> mlxsw_sp_kvdl_init
        -> mlxsw_sp_kvdl_parts_init
          -> mlxsw_sp_kvdl_part_init
            -> devlink_resource_size_get IDX (to get the current setup
                                              size from devlink)
        -> devlink_resource_occ_get_register IDX (register current
                                                  occupancy getter)
2) reload triggered by devlink command:
  -> mlxsw_devlink_core_bus_device_reload
    -> mlxsw_sp_fini
      -> mlxsw_sp_kvdl_fini
	-> devlink_resource_occ_get_unregister IDX
    (struct mlxsw_sp *mlxsw_sp is freed at this point, call to occ get
     which is using mlxsw_sp would cause use-after free)
    -> mlxsw_sp_init
      -> mlxsw_sp_kvdl_init
        -> mlxsw_sp_kvdl_parts_init
          -> mlxsw_sp_kvdl_part_init
            -> devlink_resource_size_get IDX (to get the current setup
                                              size from devlink)
        -> devlink_resource_occ_get_register IDX (register current
                                                  occupancy getter)

Fixes: d9f9b9a4 ("devlink: Add support for resource abstraction")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass struct mlxsw_core instead of devlink since it is nicer within mlxsw
code and we need both structs in mlxsw_sp_kvdl_resources_register()
anyway.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As struct mlxsw_config_profile is mapped to the payload of the FW
command of the same name, resources_query_enable flag does not belong
there. Move it to struct mlxsw_driver.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check should be done directly in mlxsw_pci_config_profile, as for
other profile items. Also, be consistent in naming with the rest and
rename to "used_kvd_sizes".
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This should not be part of the struct, as the struct fields
are tightly coupled with the FW command payload of the same name.
Just use the "granularity" define directly, as in other places.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

devlink_resource_ops should be const as the arg of register function is
also const.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>