Currently, the actual work of PF FLR is handled in the reset task,
which is asynchronous. So in some case, if the preparing and
rebuilding are not done, then the PF FLR will trigger some problems,
for example, makes hardware go into chaos.

So this patch separates the process of PF FLR from reset task, and
adds a semaphore to serialize this reset and others.

When FLR's preparing fails, if there has other higher level reset
pending or failing times less than the HCLGE_FLR_RETRY_CNT, this
preparing should be retried, otherwise PF and its VF may get into
wrong state.

BTW, while the hardware reports misc interrupt during pcie_flr(),
the driver can not receive this interrupt anymore, so disable it
when hclge_flr_prepare() return, and re-enable it when enter
hclge_flr_done().
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mutex vport_cfg_mutex has been used to protect uc_mac_list,
mc_mac_list and vlan_list from being modified by unloading
or reset task at the same time. But now unloading will
set up HCLGE_STATE_REMOVING flag and call cancel_work_sync to
break down this race condition, so this mutex is unnecessary.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

service_task will be scheduled  per second to do some periodic
jobs. When reset fails, it means this device is not available
now, so the periodic jobs do not need to be handled.

This patch adds flag HCLGE_STATE_RST_FAIL/HCLGEVF_STATE_RST_FAIL
to indicate that reset fails, and checks this flag before
schedule periodic task.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are three work (mbx_service_task, service_task,
rst_service_task) in the HNS3 driver, mbx_service_task is for
handling mailbox work, service_task is for periodic management
issue and rst_service_task is for reset related issue, which can
be handled in a single work.

This patch removes the mbx_service_task and rst_service_task
work, and moves the related handling to the service_task work
in order to remove concurrency between the three work and to
improve efficiency.

BTW, since stats_timer in struct hclge_hw_stats is not needed
anymore, so removes the definition of struct hclge_hw_stats,
and moves mac_stats into struct hclge_dev.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to hardware user manual, bits5~7 in register
HCLGE_MISC_VECTOR_INT_STS means reset interrupts status,
but HCLGE_RESET_INT_M is defined as bits0~2 now. So it
will make hclge_reset_err_handle() read the wrong reset
interrupt status.

This patch fixes this wrong bit mask.

Fixes: 2336f19d ("net: hns3: check reset interrupt status when reset fails")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macros HCLGE_MPF_ENBALE and HCLGEVF_MPF_ENBALE are defined but never
used.  I was going to fix the spelling mistake "ENBALE" -> "ENABLE" but
found these macros are not used, so they can be removed.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch corrects the SPDX License Identifier style in
header files related to Hisilicon network devices. For C header files
Documentation/process/license-rules.rst mandates C-like comments
(opposed to C source files where C++ style should be used)

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NNishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To make the code more readable, this patch replaces
some magic numbers with macro or sizeof operation.

Also uses macro lower_32_bits and upper_32_bits to
get bits 0-31 and 32-63 of a number, instead of
using type conversion and '>>' operation.

No functional change.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When reset fails, there is some information that will help for
finding out why does reset fail. and removes an unused
core_rst_cnt field in struct hclge_rst_stats.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the num_msi_left means the vector numbers of NIC,
but if the PF supported RoCE, it contains the vector numbers
of NIC and RoCE(Not expected).

This may cause interrupts lost in some case, because of the
NIC module used the vector resources which belongs to RoCE.

This patch adds a new variable num_nic_msi to store the vector
numbers of NIC, and adjust the default TQP numbers and rss_size
according to the value of num_nic_msi.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for configuring bandwidth of VF on the host
for HNS3 drivers.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

This patch adds supports for setting VF trust by host. If specified
VF is trusted, then it can enable promisc(include allmulti mode).
If a trusted VF enabled promisc, and being untrusted, host will
disable promisc mode for this VF.

For VF will update its promisc mode from set_rx_mode now, so it's
unnecessary to set broadcst promisc mode when initialization or
reset.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

This patch adds support for spoof check configuration for VFs.
When it is enabled, "spoof checking" is done for both mac address
and VLAN. For each VF, the HW ensures that the source MAC address
(or VLAN) of every outgoing packet exists in the MAC-list (or
VLAN-list) configured for RX filtering for that VF. If not,
the packet is dropped.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

This patch adds support to configure VF link properties.
The options are auto, enable, and disable. Even if the PF
is down, the communication between VFs will be normal
if the VFs are set to enable. The commands are as follows:

'ip link set <pf> vf <vf_id> state <auto|enable|disable>'
change the VF status

'ip link show'
show the setting status
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

This patch adds more information for reset DFX. Also, adds some
cleanups to reset info, move reset_fail_cnt into struct
hclge_rst_stats, and modifies some print formats.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current loopback mode is to add 0x1F to the SMAC address
as the DMAC address and enable the promiscuous mode.
However, if the VF address is the same as the DMAC address,
the loopback test fails.

Loopback can be enabled in three places: SSU, MAC, and serdes.
By default, SSU loopback is enabled, so if the SMAC and the DMAC
are the same, the packets are looped back in the SSU. If SSU loopback
is disabled, packets can reach MAC even if SMAC is the same as DMAC.

Therefore, this patch disables the SSU loopback before the loopback
test. In this way, the SMAC and DMAC can be the same, and the
promiscuous mode does not need to be enabled. And this is not
valid in version 0x20.

This patch also uses a macro to replace 0x1F.

Fixes: c39c4d98 ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the reset interrupt will be cleared firstly, so when
reset fails, if interrupt status register has reset interrupt,
it means there is a new coming reset.

Fixes: 72e2fb07 ("net: hns3: clear reset interrupt status in hclge_irq_handle()")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hardware or IMP get specified error it may need the client
to take some special operations.

This patch implements the hns3 client's process_hw_errorx.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch optimizes the waiting time for TQP reset.
Signed-off-by: NZhongzhu Liu <liuzhongzhu@huawei.com>
Reviewed-by: NYunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:542:30:
 warning: meta_data_key_info defined but not used [-Wunused-const-variable=]
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:553:30:
 warning: tuple_key_info defined but not used [-Wunused-const-variable=]

The two variable is only used in hclge_main.c,
so just move the definition over there.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pointer type parameter should be declare as const for preventing
from its pointed value being unexpected modified.

The uninitialized variable can not be return directly. The default
return value is 0 if no abnormal result.

This patch fixes the preceding two errors, deletes redundant
declaration of a function and align one parameter.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now we can use ethtool -d command to dump some registers. However,
these registers information is not enough to find out where the problem is.

This patch adds DFX registers information after original registers
when use ethtool -d commmand to dump registers. Also, using macro
replaces some related magic number.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, PF updates link status per second. For some scenario,
it requires link down event being reported more quickly.
To solve it, firmware pushes the link change event to PF with
CMDQ message, and driver updates the link status directly.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The misc interrupt is used to schedule the reset and mailbox
subtask, and service_task delayed_work is used to do periodic
management work each second.

This patch sets the above three subtask's affinity using the
misc interrupt' affinity.

Also this patch setups a affinity notify for misc interrupt to
allow user to change the above three subtask's affinity.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use delayed work instead of using timers to trigger the
hclge_serive.

Simplify the code with one less middle function and in order
to support misc irq affinity.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When loading or unloading module, it should wait for the reset task
done before it un-initializes the client, otherwise the reset task
may cause a NULL pointer reference.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When HW is resetting, firmware is unable to handle commands
from driver. So if remove VLAN device from stack at this time,
it will fail to remove the VLAN ID from HW VLAN filter, then
the VLAN filter status is unsynced with stack.

This patch fixes it by recording the VLAN ID delete failed,
and removes them again when reset complete.

Fixes: 44e626f7 ("net: hns3: fix VLAN offload handle for VLAN inserted by port")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch does following things:
1. add the keyword const before some variables which won't be modified
   in functions.
2. changes some variables from signed to unsigned to avoid bitwise
   operation on signed variables.
3. adds or removes initialization of some variables.
4. defines a new structure to help parsing mailbox messages instead of
   using an array which is harder to get the meaning of each element.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds some macros instead of magic numbers in serval places
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to improve readability, this patch uses macros to
replace some magic numbers, and adds some comments for some
others.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VF VLAN table can only support no more than 256 VLANs. When user
adds too many VLANs, the VF VLAN table will be full, and firmware
will close the VF VLAN table for the function. When VF VLAN table
is full, and user keeps adding new VLANs, it's unnecessary to
configure the VF VLAN table, because it will always fail, and print
warning message. The worst case is adding 4K VLANs, and doing reset,
it will take much time to restore these VLANs, which may cause VF
reset fail by timeout.

Fixes: 6c251711 ("net: hns3: Disable vf vlan filter when vf vlan table is full")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PF ROCE client's init_instance() succeeds, it means this client
has been registered successfully, so we use HCLGE_STATE_ROCE_REGISTERED
to indicate that. And before calling PF ROCE client's uninit_instance(),
we clear this state.

So any operation of the ROCE client from HCLGE is not allowed if this
state is not set.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PF NIC client's init_instance() succeeds, it means this client
has been registered successfully, so we use HCLGE_STATE_NIC_REGISTERED
to indicate that. And before calling PF NIC client's uninit_instance(),
we clear this state.

So any operation of PF NIC client from HCLGE is not allowed if this
state is not set.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds aRFS support for PF. The aRFS rules are also
stored in the hardware flow director table, Use the existing
filter management functions to insert TCPv4/UDPv4/TCPv6/UDPv6
flow director filters. To avoid rule conflict, once user adds
flow director rules with ethtool, the aRFS will be disabled,
and clear exist aRFS rules. Once all user configure rules were
removed, aRFS can work again.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to be compatible with aRFS rules, this patch adds
spin_lock for flow director rule adding, deleting, querying,
and packages the rule configuration.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for FEC encoding control, user can change
FEC mode by command ethtool --set-fec, and get FEC mode by command
ethtool --show-fec. The fec capability is changed follow the port
speed. If autoneg on, the user configure fec mode will be overwritten
by autoneg result.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, we can only identify copper and fiber type, the
supported link modes of port information are always showing
SR type. This patch adds support for multiple media types,
include SR, LR CR, KR. Driver needs to query the media type
from firmware periodicly, and updates the port information.

The new port information looks like this:
Settings for eth0:
        Supported ports: [ FIBRE ]
        Supported link modes:   25000baseCR/Full
                                25000baseSR/Full
                                1000baseX/Full
                                10000baseCR/Full
                                10000baseSR/Full
                                10000baseLR/Full
        Supported pause frame use: Symmetric
        Supports auto-negotiation: No
        Supported FEC modes: None BaseR
        Advertised link modes:  Not reported
        Advertised pause frame use: No
        Advertised auto-negotiation: No
        Advertised FEC modes: Not reported
        Speed: 10000Mb/s
        Duplex: Full
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: off
        Current message level: 0x00000036 (54)
                               probe link ifdown ifup
        Link detected: yes

In order to be compatible with old firmware which only support
sfp speed, we remained using the same query command, and kept
the former logic.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MAC tnl interruptions are different from other type of RAS and MSI-X
errors, because some bits, such as OVF/LR/RF will occur during link up
and down.

The drivers should clear status of all MAC tnl interruption bits but
shouldn't print any message that would mislead the users.

In case that link down and re-up in a short time because of some reasons,
we record when they occurred, and users can query them by debugfs.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds statistics for PF's reset information,
also, provides a debugfs command to dump these statistics.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When setting vport->bw_limit to hdev->tm_info.pg_info[0].bw_limit
in hclge_tm_vport_tc_info_update, vport->bw_limit can be as big as
HCLGE_ETHER_MAX_RATE (100000), which can not fit into u16 (65535).

So this patch fixes it by using u32 for vport->bw_limit.

Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>