Following previous changes, join the other authors of this driver and
take the blame with them
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable interrupt support in meson-gxl PHY driver
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY performs just as well when left in its default configuration and
it makes senses because this poke gets reset just after init.

According to the documentation, all registers in the Analog/DSP bank are
reset when there is a mode switch from 10BT to 100BT. The bank is also
reset on power down and soft reset, so we will never see the value which
may have been set by the bootloader.

In the end, we have used the default configuration so far and there is no
reason to change now. Remove CONFIG_A6 poke to make this clear.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the generic init function to populate some of the phydev
structure fields
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add read and write helpers to manipulate banked registers on this PHY
This helps clarify the settings applied to these registers and what the
driver actually does
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define registers and bits in meson-gxl PHY driver to make a bit
more human friendly. No functional change.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Always check phy_write return values. Better to be safe than sorry
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Edward Cree says:

====================
sfc: Initial X2000-series (Medford2) support

Basic PCI-level changes to support X2000-series NICs.
Also fix unexpected-PTP-event log messages, since the timestamp format has
 been changed in these NICs and that causes us to fail to probe PTP (but we
 still get the PPS events).
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The timer mode register now has a separate field for the reload value.
Since we always use this timer with the reload (for interrupt moderation)
we set this to the same as the initial value.

Previous hardware ignores this field, so we can safely set these bits
on all hardware that uses this register.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RX_L4_CLASS field has shrunk from 3 bits to 2 bits. The upper
bit was never used in previous hardware, so we can use the new
definition throughout.

The TSO OUTER_IPID field was previously spelt differently from the
external definitions.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Log a message if PTP probing fails; if we then, unexpectedly, get PTP
 events, only log a message for the first one on each device.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Medford2 can also have 16k or 64k VI stride.  This is reported by MCDI in
 GET_CAPABILITIES, which fortunately is called before the driver does
 anything sensitive to the VI stride (such as accessing or even allocating
 VIs past the zeroth).
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support using BAR 0 on SFC9250, even though the driver doesn't bind to such
 devices yet.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf-next 2017-12-18

The following pull-request contains BPF updates for your *net-next* tree.

The main changes are:

1) Allow arbitrary function calls from one BPF function to another BPF function.
   As of today when writing BPF programs, __always_inline had to be used in
   the BPF C programs for all functions, unnecessarily causing LLVM to inflate
   code size. Handle this more naturally with support for BPF to BPF calls
   such that this __always_inline restriction can be overcome. As a result,
   it allows for better optimized code and finally enables to introduce core
   BPF libraries in the future that can be reused out of different projects.
   x86 and arm64 JIT support was added as well, from Alexei.

2) Add infrastructure for tagging functions as error injectable and allow for
   BPF to return arbitrary error values when BPF is attached via kprobes on
   those. This way of injecting errors generically eases testing and debugging
   without having to recompile or restart the kernel. Tags for opting-in for
   this facility are added with BPF_ALLOW_ERROR_INJECTION(), from Josef.

3) For BPF offload via nfp JIT, add support for bpf_xdp_adjust_head() helper
   call for XDP programs. First part of this work adds handling of BPF
   capabilities included in the firmware, and the later patches add support
   to the nfp verifier part and JIT as well as some small optimizations,
   from Jakub.

4) The bpftool now also gets support for basic cgroup BPF operations such
   as attaching, detaching and listing current BPF programs. As a requirement
   for the attach part, bpftool can now also load object files through
   'bpftool prog load'. This reuses libbpf which we have in the kernel tree
   as well. bpftool-cgroup man page is added along with it, from Roman.

5) Back then commit e87c6bc3 ("bpf: permit multiple bpf attachments for
   a single perf event") added support for attaching multiple BPF programs
   to a single perf event. Given they are configured through perf's ioctl()
   interface, the interface has been extended with a PERF_EVENT_IOC_QUERY_BPF
   command in this work in order to return an array of one or multiple BPF
   prog ids that are currently attached, from Yonghong.

6) Various minor fixes and cleanups to the bpftool's Makefile as well
   as a new 'uninstall' and 'doc-uninstall' target for removing bpftool
   itself or prior installed documentation related to it, from Quentin.

7) Add CONFIG_CGROUP_BPF=y to the BPF kernel selftest config file which is
   required for the test_dev_cgroup test case to run, from Naresh.

8) Fix reporting of XDP prog_flags for nfp driver, from Jakub.

9) Fix libbpf's exit code from the Makefile when libelf was not found in
   the system, also from Jakub.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Things got moved around between the original bpf_override_return patches
and the final version, and now the ftrace kprobe dispatcher assumes if
you modified the ip that you also enabled preemption.  Make a comment of
this and enable preemption, this fixes the lockdep splat that happened
when using this feature.

Fixes: 9802d865 ("bpf: add a bpf_override_function helper")
Signed-off-by: NJosef Bacik <jbacik@fb.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

netdev_bpf.flags is the input member for installing the program.
netdev_bpf.prog_flags is the output member for querying.  Set
the correct one on query.

Fixes: 92f0292b ("net: xdp: report flags program was installed with on query")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

/bin/sh's exit does not recognize -1 as a number, leading to
the following error message:

/bin/sh: 1: exit: Illegal number: -1

Use 1 as the exit code.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Alexei Starovoitov says:

====================
First of all huge thank you to Daniel, John, Jakub, Edward and others who
reviewed multiple iterations of this patch set over the last many months
and to Dave and others who gave critical feedback during netconf/netdev.

The patch is solid enough and we thought through numerous corner cases,
but it's not the end. More followups with code reorg and features to follow.

TLDR: Allow arbitrary function calls from bpf function to another bpf function.

Since the beginning of bpf all bpf programs were represented as a single function
and program authors were forced to use always_inline for all functions
in their C code. That was causing llvm to unnecessary inflate the code size
and forcing developers to move code to header files with little code reuse.

With a bit of additional complexity teach verifier to recognize
arbitrary function calls from one bpf function to another as long as
all of functions are presented to the verifier as a single bpf program.
Extended program layout:
..
r1 = ..    // arg1
r2 = ..    // arg2
call pc+1  // function call pc-relative
exit
.. = r1    // access arg1
.. = r2    // access arg2
..
call pc+20 // second level of function call
...

It allows for better optimized code and finally allows to introduce
the core bpf libraries that can be reused in different projects,
since programs are no longer limited by single elf file.
With function calls bpf can be compiled into multiple .o files.

This patch is the first step. It detects programs that contain
multiple functions and checks that calls between them are valid.
It splits the sequence of bpf instructions (one program) into a set
of bpf functions that call each other. Calls to only known
functions are allowed. Since all functions are presented to
the verifier at once conceptually it is 'static linking'.

Future plans:
- introduce BPF_PROG_TYPE_LIBRARY and allow a set of bpf functions
  to be loaded into the kernel that can be later linked to other
  programs with concrete program types. Aka 'dynamic linking'.

- introduce function pointer type and indirect calls to allow
  bpf functions call other dynamically loaded bpf functions while
  the caller bpf function is already executing. Aka 'runtime linking'.
  This will be more generic and more flexible alternative
  to bpf_tail_calls.

FAQ:
Q: Interpreter and JIT changes mean that new instruction is introduced ?
A: No. The call instruction technically stays the same. Now it can call
   both kernel helpers and other bpf functions.
   Calling convention stays the same as well.
   From uapi point of view the call insn got new 'relocation' BPF_PSEUDO_CALL
   similar to BPF_PSEUDO_MAP_FD 'relocation' of bpf_ldimm64 insn.

Q: What had to change on LLVM side?
A: Trivial LLVM patch to allow calls was applied to upcoming 6.0 release:
   https://reviews.llvm.org/rL318614
   with few bugfixes as well.
   Make sure to build the latest llvm to have bpf_call support.

More details in the patches.
====================
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Add some additional checks for few more corner cases.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

similar to x64 add support for bpf-to-bpf calls.
When program has calls to in-kernel helpers the target call offset
is known at JIT time and arm64 architecture needs 2 passes.
With bpf-to-bpf calls the dynamically allocated function start
is unknown until all functions of the program are JITed.
Therefore (just like x64) arm64 JIT needs one extra pass over
the program to emit correct call offsets.

Implementation detail:
Avoid being too clever in 64-bit immediate moves and
always use 4 instructions (instead of 3-4 depending on the address)
to make sure only one extra pass is needed.
If some future optimization would make it worth while to optimize
'call 64-bit imm' further, the JIT would need to do 4 passes
over the program instead of 3 as in this patch.
For typical bpf program address the mov needs 3 or 4 insns,
so unconditional 4 insns to save extra pass is a worthy trade off
at this state of JIT.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Typical JIT does several passes over bpf instructions to
compute total size and relative offsets of jumps and calls.
With multitple bpf functions calling each other all relative calls
will have invalid offsets intially therefore we need to additional
last pass over the program to emit calls with correct offsets.
For example in case of three bpf functions:
main:
  call foo
  call bpf_map_lookup
  exit
foo:
  call bar
  exit
bar:
  exit

We will call bpf_int_jit_compile() indepedently for main(), foo() and bar()
x64 JIT typically does 4-5 passes to converge.
After these initial passes the image for these 3 functions
will be good except call targets, since start addresses of
foo() and bar() are unknown when we were JITing main()
(note that call bpf_map_lookup will be resolved properly
during initial passes).
Once start addresses of 3 functions are known we patch
call_insn->imm to point to right functions and call
bpf_int_jit_compile() again which needs only one pass.
Additional safety checks are done to make sure this
last pass doesn't produce image that is larger or smaller
than previous pass.

When constant blinding is on it's applied to all functions
at the first pass, since doing it once again at the last
pass can change size of the JITed code.

Tested on x64 and arm64 hw with JIT on/off, blinding on/off.
x64 jits bpf-to-bpf calls correctly while arm64 falls back to interpreter.
All other JITs that support normal BPF_CALL will behave the same way
since bpf-to-bpf call is equivalent to bpf-to-kernel call from
JITs point of view.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

global bpf_jit_enable variable is tested multiple times in JITs,
blinding and verifier core. The malicious root can try to toggle
it while loading the programs. This race condition was accounted
for and there should be no issues, but it's safer to avoid
this race condition.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

though bpf_call is still the same call instruction and
calling convention 'bpf to bpf' and 'bpf to helper' is the same
the interpreter has to oparate on 'struct bpf_insn *'.
To distinguish these two cases add a kernel internal opcode and
mark call insns with it.
This opcode is seen by interpreter only. JITs will never see it.
Also add tiny bit of debug code to aid interpreter debugging.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

add large semi-artificial XDP test with 18 functions to stress test
bpf call verification logic
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

strip always_inline from test_l4lb.c and compile it with -fno-inline
to let verifier go through 11 function with various function arguments
and return values
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

- recognize relocation emitted by llvm
- since all regular function will be kept in .text section and llvm
  takes care of pc-relative offsets in bpf_call instruction
  simply copy all of .text to relevant program section while adjusting
  bpf_call instructions in program section to point to newly copied
  body of instructions from .text
- do so for all programs in the elf file
- set all programs types to the one passed to bpf_prog_load()

Note for elf files with multiple programs that use different
functions in .text section we need to do 'linker' style logic.
This work is still TBD
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

adjust two tests, since verifier got smarter
and add new one to test stack_zero logic
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

programs with function calls are often passing various
pointers via stack. When all calls are inlined llvm
flattens stack accesses and optimizes away extra branches.
When functions are not inlined it becomes the job of
the verifier to recognize zero initialized stack to avoid
exploring paths that program will not take.
The following program would fail otherwise:

ptr = &buffer_on_stack;
*ptr = 0;
...
func_call(.., ptr, ...) {
  if (..)
    *ptr = bpf_map_lookup();
}
...
if (*ptr != 0) {
  // Access (*ptr)->field is valid.
  // Without stack_zero tracking such (*ptr)->field access
  // will be rejected
}

since stack slots are no longer uniform invalid | spill | misc
add liveness marking to all slots, but do it in 8 byte chunks.
So if nothing was read or written in [fp-16, fp-9] range
it will be marked as LIVE_NONE.
If any byte in that range was read, it will be marked LIVE_READ
and stacksafe() check will perform byte-by-byte verification.
If all bytes in the range were written the slot will be
marked as LIVE_WRITTEN.
This significantly speeds up state equality comparison
and reduces total number of states processed.

                    before   after
bpf_lb-DLB_L3.o       2051    2003
bpf_lb-DLB_L4.o       3287    3164
bpf_lb-DUNKNOWN.o     1080    1080
bpf_lxc-DDROP_ALL.o   24980   12361
bpf_lxc-DUNKNOWN.o    34308   16605
bpf_netdev.o          15404   10962
bpf_overlay.o         7191    6679
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Add extensive set of tests for bpf_call verification logic:

calls: basic sanity
calls: using r0 returned by callee
calls: callee is using r1
calls: callee using args1
calls: callee using wrong args2
calls: callee using two args
calls: callee changing pkt pointers
calls: two calls with args
calls: two calls with bad jump
calls: recursive call. test1
calls: recursive call. test2
calls: unreachable code
calls: invalid call
calls: jumping across function bodies. test1
calls: jumping across function bodies. test2
calls: call without exit
calls: call into middle of ld_imm64
calls: call into middle of other call
calls: two calls with bad fallthrough
calls: two calls with stack read
calls: two calls with stack write
calls: spill into caller stack frame
calls: two calls with stack write and void return
calls: ambiguous return value
calls: two calls that return map_value
calls: two calls that return map_value with bool condition
calls: two calls that return map_value with incorrect bool check
calls: two calls that receive map_value via arg=ptr_stack_of_caller. test1
calls: two calls that receive map_value via arg=ptr_stack_of_caller. test2
calls: two jumps that receive map_value via arg=ptr_stack_of_jumper. test3
calls: two calls that receive map_value_ptr_or_null via arg. test1
calls: two calls that receive map_value_ptr_or_null via arg. test2
calls: pkt_ptr spill into caller stack
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Allow arbitrary function calls from bpf function to another bpf function.

To recognize such set of bpf functions the verifier does:
1. runs control flow analysis to detect function boundaries
2. proceeds with verification of all functions starting from main(root) function
It recognizes that the stack of the caller can be accessed by the callee
(if the caller passed a pointer to its stack to the callee) and the callee
can store map_value and other pointers into the stack of the caller.
3. keeps track of the stack_depth of each function to make sure that total
stack depth is still less than 512 bytes
4. disallows pointers to the callee stack to be stored into the caller stack,
since they will be invalid as soon as the callee returns
5. to reuse all of the existing state_pruning logic each function call
is considered to be independent call from the verifier point of view.
The verifier pretends to inline all function calls it sees are being called.
It stores the callsite instruction index as part of the state to make sure
that two calls to the same callee from two different places in the caller
will be different from state pruning point of view
6. more safety checks are added to liveness analysis

Implementation details:
. struct bpf_verifier_state is now consists of all stack frames that
  led to this function
. struct bpf_func_state represent one stack frame. It consists of
  registers in the given frame and its stack
. propagate_liveness() logic had a premature optimization where
  mark_reg_read() and mark_stack_slot_read() were manually inlined
  with loop iterating over parents for each register or stack slot.
  Undo this optimization to reuse more complex mark_*_read() logic
. skip_callee() logic is not necessary from safety point of view,
  but without it mark_*_read() markings become too conservative,
  since after returning from the funciton call a read of r6-r9
  will incorrectly propagate the read marks into callee causing
  inefficient pruning later
. mark_*_read() logic is now aware of control flow which makes it
  more complex. In the future the plan is to rewrite liveness
  to be hierarchical. So that liveness can be done within
  basic block only and control flow will be responsible for
  propagation of liveness information along cfg and between calls.
. tail_calls and ld_abs insns are not allowed in the programs with
  bpf-to-bpf calls
. returning stack pointers to the caller or storing them into stack
  frame of the caller is not allowed

Testing:
. no difference in cilium processed_insn numbers
. large number of tests follows in next patches
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Allow arbitrary function calls from bpf function to another bpf function.

Since the beginning of bpf all bpf programs were represented as a single function
and program authors were forced to use always_inline for all functions
in their C code. That was causing llvm to unnecessary inflate the code size
and forcing developers to move code to header files with little code reuse.

With a bit of additional complexity teach verifier to recognize
arbitrary function calls from one bpf function to another as long as
all of functions are presented to the verifier as a single bpf program.
New program layout:
r6 = r1    // some code
..
r1 = ..    // arg1
r2 = ..    // arg2
call pc+1  // function call pc-relative
exit
.. = r1    // access arg1
.. = r2    // access arg2
..
call pc+20 // second level of function call
...

It allows for better optimized code and finally allows to introduce
the core bpf libraries that can be reused in different projects,
since programs are no longer limited by single elf file.
With function calls bpf can be compiled into multiple .o files.

This patch is the first step. It detects programs that contain
multiple functions and checks that calls between them are valid.
It splits the sequence of bpf instructions (one program) into a set
of bpf functions that call each other. Calls to only known
functions are allowed. In the future the verifier may allow
calls to unresolved functions and will do dynamic linking.
This logic supports statically linked bpf functions only.

Such function boundary detection could have been done as part of
control flow graph building in check_cfg(), but it's cleaner to
separate function boundary detection vs control flow checks within
a subprogram (function) into logically indepedent steps.
Follow up patches may split check_cfg() further, but not check_subprogs().

Only allow bpf-to-bpf calls for root only and for non-hw-offloaded programs.
These restrictions can be relaxed in the future.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull rdma fixes from Jason Gunthorpe:
 "More fixes from testing done on the rc kernel, including more SELinux
  testing. Looking forward, lockdep found regression today in ipoib
  which is still being fixed.

  Summary:

   - Fix for SELinux on the umad SMI path. Some old hardware does not
     fill the PKey properly exposing another bug in the newer SELinux
     code.

   - Check the input port as we can exceed array bounds from this user
     supplied value

   - Users are unable to use the hash field support as they want due to
     incorrect checks on the field restrictions, correct that so the
     feature works as intended

   - User triggerable oops in the NETLINK_RDMA handler

   - cxgb4 driver fix for a bad interaction with CQ flushing in iser
     caused by patches in this merge window, and bad CQ flushing during
     normal close.

   - Unbalanced memalloc_noio in ipoib in an error path"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  IB/ipoib: Restore MM behavior in case of tx_ring allocation failure
  iw_cxgb4: only insert drain cqes if wq is flushed
  iw_cxgb4: only clear the ARMED bit if a notification is needed
  RDMA/netlink: Fix general protection fault
  IB/mlx4: Fix RSS hash fields restrictions
  IB/core: Don't enforce PKey security on SMI MADs
  IB/core: Bound check alternate path port number

Pull i2c fixes from Wolfram Sang:
 "Two bugfixes for the AT24 I2C eeprom driver and some minor corrections
  for I2C bus drivers"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: piix4: Fix port number check on release
  i2c: stm32: Fix copyrights
  i2c-cht-wc: constify platform_device_id
  eeprom: at24: change nvmem stride to 1
  eeprom: at24: fix I2C device selection for runtime PM

Pull NFS client fixes from Anna Schumaker:
 "This has two stable bugfixes, one to fix a BUG_ON() when
  nfs_commit_inode() is called with no outstanding commit requests and
  another to fix a race in the SUNRPC receive codepath.

  Additionally, there are also fixes for an NFS client deadlock and an
  xprtrdma performance regression.

  Summary:

  Stable bugfixes:
   - NFS: Avoid a BUG_ON() in nfs_commit_inode() by not waiting for a
     commit in the case that there were no commit requests.
   - SUNRPC: Fix a race in the receive code path

  Other fixes:
   - NFS: Fix a deadlock in nfs client initialization
   - xprtrdma: Fix a performance regression for small IOs"

* tag 'nfs-for-4.15-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  SUNRPC: Fix a race in the receive code path
  nfs: don't wait on commit in nfs_commit_inode() if there were no commit requests
  xprtrdma: Spread reply processing over more CPUs
  nfs: fix a deadlock in nfs client initialization

This reverts commits 5c9d2d5c, c7da82b8, and e7fe7b5c.

We'll probably need to revisit this, but basically we should not
complicate the get_user_pages_fast() case, and checking the actual page
table protection key bits will require more care anyway, since the
protection keys depend on the exact state of the VM in question.

Particularly when doing a "remote" page lookup (ie in somebody elses VM,
not your own), you need to be much more careful than this was.  Dave
Hansen says:

 "So, the underlying bug here is that we now a get_user_pages_remote()
  and then go ahead and do the p*_access_permitted() checks against the
  current PKRU. This was introduced recently with the addition of the
  new p??_access_permitted() calls.

  We have checks in the VMA path for the "remote" gups and we avoid
  consulting PKRU for them. This got missed in the pkeys selftests
  because I did a ptrace read, but not a *write*. I also didn't
  explicitly test it against something where a COW needed to be done"

It's also not entirely clear that it makes sense to check the protection
key bits at this level at all.  But one possible eventual solution is to
make the get_user_pages_fast() case just abort if it sees protection key
bits set, which makes us fall back to the regular get_user_pages() case,
which then has a vma and can do the check there if we want to.

We'll see.

Somewhat related to this all: what we _do_ want to do some day is to
check the PAGE_USER bit - it should obviously always be set for user
pages, but it would be a good check to have back.  Because we have no
generic way to test for it, we lost it as part of moving over from the
architecture-specific x86 GUP implementation to the generic one in
commit e585513b ("x86/mm/gup: Switch GUP to the generic
get_user_page_fast() implementation").

Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Clamp timeouts to INT_MAX in conntrack, from Jay Elliot.

 2) Fix broken UAPI for BPF_PROG_TYPE_PERF_EVENT, from Hendrik
    Brueckner.

 3) Fix locking in ieee80211_sta_tear_down_BA_sessions, from Johannes
    Berg.

 4) Add missing barriers to ptr_ring, from Michael S. Tsirkin.

 5) Don't advertise gigabit in sh_eth when not available, from Thomas
    Petazzoni.

 6) Check network namespace when delivering to netlink taps, from Kevin
    Cernekee.

 7) Kill a race in raw_sendmsg(), from Mohamed Ghannam.

 8) Use correct address in TCP md5 lookups when replying to an incoming
    segment, from Christoph Paasch.

 9) Add schedule points to BPF map alloc/free, from Eric Dumazet.

10) Don't allow silly mtu values to be used in ipv4/ipv6 multicast, also
    from Eric Dumazet.

11) Fix SKB leak in tipc, from Jon Maloy.

12) Disable MAC learning on OVS ports of mlxsw, from Yuval Mintz.

13) SKB leak fix in skB_complete_tx_timestamp(), from Willem de Bruijn.

14) Add some new qmi_wwan device IDs, from Daniele Palmas.

15) Fix static key imbalance in ingress qdisc, from Jiri Pirko.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  net: qcom/emac: Reduce timeout for mdio read/write
  net: sched: fix static key imbalance in case of ingress/clsact_init error
  net: sched: fix clsact init error path
  ip_gre: fix wrong return value of erspan_rcv
  net: usb: qmi_wwan: add Telit ME910 PID 0x1101 support
  pkt_sched: Remove TC_RED_OFFLOADED from uapi
  net: sched: Move to new offload indication in RED
  net: sched: Add TCA_HW_OFFLOAD
  net: aquantia: Increment driver version
  net: aquantia: Fix typo in ethtool statistics names
  net: aquantia: Update hw counters on hw init
  net: aquantia: Improve link state and statistics check interval callback
  net: aquantia: Fill in multicast counter in ndev stats from hardware
  net: aquantia: Fill ndev stat couters from hardware
  net: aquantia: Extend stat counters to 64bit values
  net: aquantia: Fix hardware DMA stream overload on large MRRS
  net: aquantia: Fix actual speed capabilities reporting
  sock: free skb in skb_complete_tx_timestamp on error
  s390/qeth: update takeover IPs after configuration change
  s390/qeth: lock IP table while applying takeover changes
  ...

Pull USB fixes from Greg KH:
 "Here are some USB fixes for 4.15-rc4.

  There is the usual handful gadget/dwc2/dwc3 fixes as always, for
  reported issues. But the most important things in here is the core fix
  from Alan Stern to resolve a nasty security bug (my first attempt is
  reverted, Alan's was much cleaner), as well as a number of usbip fixes
  from Shuah Khan to resolve those reported security issues.

  All of these have been in linux-next with no reported issues"

* tag 'usb-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: core: prevent malicious bNumInterfaces overflow
  Revert "USB: core: only clean up what we allocated"
  USB: core: only clean up what we allocated
  Revert "usb: gadget: allow to enable legacy drivers without USB_ETH"
  usb: gadget: webcam: fix V4L2 Kconfig dependency
  usb: dwc2: Fix TxFIFOn sizes and total TxFIFO size issues
  usb: dwc3: gadget: Fix PCM1 for ISOC EP with ep->mult less than 3
  usb: dwc3: of-simple: set dev_pm_ops
  usb: dwc3: of-simple: fix missing clk_disable_unprepare
  usb: dwc3: gadget: Wait longer for controller to end command processing
  usb: xhci: fix TDS for MTK xHCI1.1
  xhci: Don't add a virt_dev to the devs array before it's fully allocated
  usbip: fix stub_send_ret_submit() vulnerability to null transfer_buffer
  usbip: prevent vhci_hcd driver from leaking a socket pointer address
  usbip: fix stub_rx: harden CMD_SUBMIT path to handle malicious input
  usbip: fix stub_rx: get_pipe() to validate endpoint number
  tools/usbip: fixes potential (minor) "buffer overflow" (detected on recent gcc with -Werror)
  USB: uas and storage: Add US_FL_BROKEN_FUA for another JMicron JMS567 ID
  usb: musb: da8xx: fix babble condition handling

Build bot reported warning about invalid printk formats on 32bit
architectures.  Use %zu for size_t and %zd ptr diff.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>