We must call netif_carrier_off() after the device is registered, not
before, to set the operational state and user-space IFF_RUNNING flag
correctly.

Since we don't want observers to see an intermediate state, open-code
register_netdev() and add efx_update_name() and netif_carrier_off()
into the locked region.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If nothing has been written into the qeth sysfs-attribute layer2,
its value is "-1" meaning "not yet defined". But the value is
displayed as "1" meaning "layer2 selected". The patch changes the
reading of this "-1"-value to "-1" to make clear the layer2-attribute
has not yet been defined.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qeth displayed an entry in /proc/service_level even when no valid
MCL-string was available (the MCL info is blank). The change is to
create an entry in /proc/service_level only when MCL-string is
non-zero.
Signed-off-by: NKlaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clear separation of cast-type determination (send path) for layer-2
resp. layer-3. Allowing to have inline functions for qeth layer-
discipline.
Signed-off-by: NKlaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case the IP address list contains entries (not removed when the device was set
offline) this entries should be registered next time the device is brought online.
In the past this was done implicitly with the device open call but since we wait
in the set IPv4 IPA and the device open common code holds various locks this
does not work any longer.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Qeth HiperSockets support now retries sending of packets when the
IBM System z signals a temporary resource shortage (e.g. target
buffer full). The packet is enqueued into the device queue.
After 3 times of unsuccessful send the packet is dropped.
Signed-off-by: NKlaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.100.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This brings the 57780's phy into IEEE compliance by suppressing the
common mode oscillation.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the AC131 fast ethernet transceiver.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the BCM50610M phy ID.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts the code to use the PHY_IS_FET flag rather than the
ASIC revision to decide whether or not to use FET paths.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom's phys come in two distinctly different register layouts.  For
the lack of an official term to distinguish between the two formats, we
can loosely categorize them by their fast ethernet or gigabit ethernet
transceiver description.  This patch creates the (driver-internal) Fast
Ethernet Transceiver (FET) namespace and converts the 5906 EPHY
definitions over.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch tunes the timeouts the CPMU uses to decide when to switch
from the clocks output by the PHY to internal clock sources.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the 57788 and removes support for the 57720
which was never released.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most older tg3 devices only supported a PCIe maximum payload size of
128 bytes.  More recent devices bump this limit up to 256 bytes
though.  This patch modifies the code so that the MPS limit is only
enforced on those devices that only allow the 128 byte setting.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Julia Lawall discovered that the TG3_FLG2_TSO_CAPABLE flag was being
compared against the wrong flags device member.  This patch implements
the fix.
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prevents a tx BD corruption bug by preventing the device from
powering down the PLL from L1 if the link speed is 10Mbps or 100Mbps.

The same bits are also used to prevent a system hang during chip reset
resulting from a complicated set of events that ultimately leads to
PCIe block register corruption.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes some PCIe link receiver errors by decreasing the internal
electrical idle timeout.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove function e1000_mta_set, as it is no longer called
Signed-off-by: NDave Graham <david.graham@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were already exporting TSO6 to the vlan, but we weren't exporting the
checksum support for IPV6 which was causing warning messages to be
displayed when doing IPv6 TSO over a vlan.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have some ~40 functions that were being called out with 'make
namespacecheck'.  This patch changes these functions to be static.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix ethtool get_settings logic to report 10G & 1G advertised and
supported link modes in all 8259x 10G backplane connection types
except for 82598EB BX network connection type.
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the interface is put in bridged mode, destination mac
addresses are unknown to firmware. So packets take a slow
path (lower priority) in firmware reducing performance.

Firmware can cache limited number of remote unicast mac
addresses for certain interval, if "dynamic mac learning"
mode is enabled.

Driver needs to enable this "mac learning" mode in firmware.
Currently this is done through net device class sysfs entry,
possibly this can also be done upon netlink notifications to
from bridge.
Signed-off-by: NNarender Kumar <narender.kumar@qlogic.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Consolidate all MAC/PHY access functions into netxen_nic_hw.c
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement common function for locking/unlocking 8 hardware
semaphores used for serializing access to shared resouces
on a NIC board by different PCI functions.

As by definition, callers of these semaphore API can be
put to sleep till the semaphore is locked.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove code for phy access on unreleased NX2031 based quad-gig board.

NX3031 based production quad-gig boards do not require direct phy
access by driver.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of fully initializing an unusable second r6040
device, perform the PHY detection earlier and bail out
in r6040_init_one when we could not read the PHY identifier.
Signed-off-by: NMark Kelly <mark@bifferos.com>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the unused pioaddr variable.
Signed-off-by: NMark Kelly <mark@bifferos.com>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Consolidate register definitions in netxen_nic_hdr.h
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement pci driver shutdown functionality, this helps
quiescing all PCI transaction before chipset is reset.

Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all tx skb mapping code into netxen_map_tx_skb().
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If netxen_need_fw_reset() return 0 [ implies firmware is up
and running], still go through dma mask check, etc.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ethtool -K knob to control LRO in firmware.
LRO path is completely separated from GRO, LRO packets
are still fed with netif_receive_skb().

Also fix ethtool statistics to include LRO packets.
Also use correct message type while configuring interrupt coalescing.
Signed-off-by: NNarender Kumar <narender.kumar@qlogic.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The structure, once initialized, never changes.
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Set the USE_INT_PARAM bit so the rx-frames-irq and tx-frames-irq will take
  effect on 5709.
- Increase the default rx-frames to reduce interrupt count.
- Decrease the default rx-frames-irq and tx-frames-irq to catch more events
  during NAPI poll.

All these will reduce interrupts without affecting latency.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report this counter to ethtool -S and include it in netstat.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add flag to expand the workaround to both chips.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When unable to allocate memory for new MTU or new ring size, we need
to close the device to prevent it from crashing.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>